Leatherman weak points
-
Life's sick comedy.
-
@Mike D said:
What I want to know Kwakster is do you repair multi"s like professionally?I have two Swisstools that need fixed...
Yes, you can say that.
Although i'm mainly a content editor, someone who writes productinfo and background information on websites, repairing mostly Leatherman multitools and Buck knives, as well as sharpening are part of my daily routine.
But i only work three days a week, :DBut sorry, the company i work for doesn't carry Victorinox, only Wenger.
I know that Victorinox owns Wenger, but where i live the two are strictly separated. -
@kwakster said:
Biggest problem i encounter are always the locking tabs.
When exerting pressure on one of the smaller items, all the force gets transferred onto 2 tiny metal pins which cannot handle this very well and shear off.kwakster, which Leatherman model are you referring to?
On the Fuse, Blast, Core, Wave, Charge, Surge, etc, there are metal tabs on the lock bar which fit into slots. (circled) I would have thought this arrangement would take the load completely off the two pins?? ???

-
Biggest problem i encounter are always the locking tabs.
When exerting pressure on one of the smaller items, all the force gets transferred onto 2 tiny metal pins which cannot handle this very well and shear off.kwakster, which Leatherman model are you referring to?
On the Fuse, Blast, Core, Wave, Charge, Surge, etc, there are metal tabs on the lock bar which fit into slots. (circled) I would have thought this arrangement would take the load completely off the two pins?? ???

I see this problem occuring on all models with locking tabs, but mostly on Wave's, Charges, and Blasts while we sell those models the most.
The lockbar that fits into the slots needs just a little room to function properly, meaning it hasn't got a supertight fit into it's slot.
And this is just enough to transfer the forces excerted mainly on the screwdrivers onto the small pins or hinges, which obviously cannot handle this stress very well. -
Very interesting. I would not have guessed this area was a weakness. :-\
@kwakster said:
Third biggest problem is the tiny metal pin that helps to keep the plierhead seated when closed.
This pin bends and breaks easily, at which point the tool doesn't close easily anymore, you will have to guide the plierhead by hand.
My solution to this is as follows.
Just in front of the little pin is a rivet which is cut off short to make room for the plierhead.
If a longer rivet was used the plierhead could rest upon it and the weak metal pin could be left out....and on this point I'm assuming you refer to the pin circled below? It does indeed seem like a fragile part. (although I've never had one break)

How do you repair tools that come to you with this pin broken? ???
-
@J-sews said:
Very interesting. I would not have guessed this area was a weakness. :-\Third biggest problem is the tiny metal pin that helps to keep the plierhead seated when closed.
This pin bends and breaks easily, at which point the tool doesn't close easily anymore, you will have to guide the plierhead by hand.
My solution to this is as follows.
Just in front of the little pin is a rivet which is cut off short to make room for the plierhead.
If a longer rivet was used the plierhead could rest upon it and the weak metal pin could be left out....and on this point I'm assuming you refer to the pin circled below? It does indeed seem like a fragile part. (although I've never had one break)

How do you repair tools that come to you with this pin broken? ???
Yep, that is the pin i was talking about.
Most of the time it starts to bend outwards first, and breaks off when people try to bend it back.
When i get one of these back in shop i have to replace the whole leg, and build all the items back into it.In your picture you can also see the rivet i was talking about, just right from the pin.
If Leatherman would just leave it longer, instead of cutting it short, it would be a whole lot stronger than that weak little pin. -
Kwakster while we are asking ::) ::) ::) What tool do you use to remove LM's knurled fasteners ? And how do I get them
. Does it involve "Black ops" , 007 & a magic wand ? I can not bring myself to creating a set of spoony's customized sockets ( hammering the knurl impression into a cheap socket). 
-
@MultiMat said:
Kwakster while we are asking ::) ::) ::) What tool do you use to remove LM's knurled fasteners ? And how do I get them
. Does it involve "Black ops" , 007 & a magic wand ? I can not bring myself to creating a set of spoony's customized sockets ( hammering the knurl impression into a cheap socket). 
There are some flat pieces of steel with holes exactly forming the outline of specific knurled fasteners, and next to these i also have several specialized sockets to put on a screwdriver fitted with a square tip.
While i'm not familiar with all the right names for these kind of tools, i think you know what i mean,I will try to make some pictures of these in a few days.
On the sockets are American brand names that i'm not familiar with, but maybe you can get them where you live. -
Very interesting. I would not have guessed this area was a weakness. :-\
Third biggest problem is the tiny metal pin that helps to keep the plierhead seated when closed.
This pin bends and breaks easily, at which point the tool doesn't close easily anymore, you will have to guide the plierhead by hand.
My solution to this is as follows.
Just in front of the little pin is a rivet which is cut off short to make room for the plierhead.
If a longer rivet was used the plierhead could rest upon it and the weak metal pin could be left out....and on this point I'm assuming you refer to the pin circled below? It does indeed seem like a fragile part. (although I've never had one break)

How do you repair tools that come to you with this pin broken? ???
Yep, that is the pin i was talking about.
Most of the time it starts to bend outwards first, and breaks off when people try to bend it back.
When i get one of these back in shop i have to replace the whole leg, and build all the items back into it.In your picture you can also see the rivet i was talking about, just right from the pin.
If Leatherman would just leave it longer, instead of cutting it short, it would be a whole lot stronger than that weak little pin.I don't know about weak??? Have you ever tried to cut one on those pins? I used to work at a place where we used the same type of metal pins and the only way to snap them was to use lineman pliers in a vice. It is a tough metal, but I suppose could give after some time, but it would have to be a long time. Also the pin inside for the plier head has never given me any problems. I have worked my Wave like a balisong before and never gave me any trouble, but I know that if anything should ever happen that LM will fix it under the 25 yr warranty :D
-
Kwakster while we are asking ::) ::) ::) What tool do you use to remove LM's knurled fasteners ? And how do I get them
. Does it involve "Black ops" , 007 & a magic wand ? I can not bring myself to creating a set of spoony's customized sockets ( hammering the knurl impression into a cheap socket). 
There are some flat pieces of steel with holes exactly forming the outline of specific knurled fasteners, and next to these i also have several specialized sockets to put on a screwdriver fitted with a square tip.
While i'm not familiar with all the right names for these kind of tools, i think you know what i mean,I will try to make some pictures of these in a few days.
On the sockets are American brand names that i'm not familiar with, but maybe you can get them where you live.I live in Australia so it might be a stretch but the internet has made the world so well connected. Photos & names of those special tools
Please :D -
Kwakster while we are asking ::) ::) ::) What tool do you use to remove LM's knurled fasteners ? And how do I get them
. Does it involve "Black ops" , 007 & a magic wand ? I can not bring myself to creating a set of spoony's customized sockets ( hammering the knurl impression into a cheap socket). 
There are some flat pieces of steel with holes exactly forming the outline of specific knurled fasteners, and next to these i also have several specialized sockets to put on a screwdriver fitted with a square tip.
While i'm not familiar with all the right names for these kind of tools, i think you know what i mean,I will try to make some pictures of these in a few days.
On the sockets are American brand names that i'm not familiar with, but maybe you can get them where you live.I live in Australia so it might be a stretch but the internet has made the world so well connected. Photos & names of those special tools
Please :DOne in the pictures shown above is the Leatherman Wave
-
Kwakster while we are asking ::) ::) ::) What tool do you use to remove LM's knurled fasteners ? And how do I get them
. Does it involve "Black ops" , 007 & a magic wand ? I can not bring myself to creating a set of spoony's customized sockets ( hammering the knurl impression into a cheap socket). 
There are some flat pieces of steel with holes exactly forming the outline of specific knurled fasteners, and next to these i also have several specialized sockets to put on a screwdriver fitted with a square tip.
While i'm not familiar with all the right names for these kind of tools, i think you know what i mean,I will try to make some pictures of these in a few days.
On the sockets are American brand names that i'm not familiar with, but maybe you can get them where you live.I live in Australia so it might be a stretch but the internet has made the world so well connected. Photos & names of those special tools
Please :DOne in the pictures shown above is the Leatherman Wave
That's not what he meant. :D
He's talking about the tools to remove the knurled screws.
-
Ah hell, I feel like a ******* idiot!!!! lol
:D -
@jdailey4206966 said:
Ah hell, I feel like a ******* :D
idiot!!!! lolThat's ok, I feel like that most of the time too. :D
-
Don't we all? ??? :)
-
@Leatherman123 said:
Don't we all? ??? :)No! :D
-
What I want to know Kwakster is do you repair multi"s like professionally?
I have two Swisstools that need fixed...
How did you manage to break them? They seem really solid.
Neither of them are really broken.
The first one an X has a bunk plier head that the pivot is so loose on that the wire cutters make serious contact with each other when closing. Yes I know I can send it in for warranty work just haven't done it yet.
The second is my RS, my helper cut a live extension cord with and almost burned a hole in the blade at the same time. I polished up the blade and resharpened it and its fine really. But there is something wrong with the pivot on the blade and the crate opener next to it now. They are both much harder to get out, and they both clump together when trying to open either.
-
Send them in for warranty. You will get them back within a week or two!
-
What I want to know Kwakster is do you repair multi"s like professionally?
I have two Swisstools that need fixed...
How did you manage to break them? They seem really solid.
Neither are either of them really broken.
The first one and X has a bunk plier head that the pivot is so loose on that the wire cutters make serious contact with each other when closing. Yes I know I can send it in for warranty work just haven't done it yet.
The second is my RS, my helper cut a live extension cord with and almost burned a hole in the blade at the same time. I polished up the blade and resharpened it and its fine really. But there is something wrong with the pivot on the blade and the crate opener next to it now. They are both much harder to get out, and they both clump together when trying to open either.
By all means do send them in for warranty work! I read on here where a man cut a live wire with is super tool and it nearly ate all the wire cutter out of them. He sent them in and had them back in 2 weeks.
If SAK has a full lifetime warranty, than this should be covered as well.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login