One of the reasons I keep picking Gerber over Leatherman ...
-
@detron said:
I do not own one to check with, but the OHT might be closer to the gerber when it comes to handle seperation. (since they basically used Gerber's design concepts)Unfortunately I don't have one for comparison, but I have tried the OHT and I found it very hand filling in the closed position. That said, there seems to be more at play with many of these tools than just where the handles sit at the open and closed positions. Some tools splay more than other depending on the aperture of the main gripping section, and how far forwards of the pivot that area is. Without putting the same diameter item within the pliers and doing a side by side comparison with the other stuff like I'm doing here, I can't really offer anything definitive as to the OHT "in use"
-
Excellent series of posts, 50ft-trad. I concur with several points concerning the ease of using Gerber vs. non-Gerber pliers, but I think the majority of your analysis addresses gripping larger objects.
For me, the Gerber MP400 and MP600 series don't do as well as the competition when gripping small objects. In that case, I find their handles are too close together. They are so close together that it's difficult to keep a finger in between, a technique I use to better control the gripping action of smaller objects. Perhaps spring loading the pliers would help there.
While most people sing the praises of the Leatherman Wave, the sharp top edges of the handles and tools chafe my palms when using the pliers. Plus, the knife spine can pinch my palm sometimes when using the pliers. I had the same chafing problem with the Surge (and it was just too big and heavy).
The Skeletool pliers has drawbacks, too. The asymmetric handles restrict you to holding them in only one position instead of two, and the curvature of the bottom handle forces my hand to slide towards the plier head.
I had a bad pinching experience with the original Gerber Multi Pliers several years ago. That led to using a long succession of Leatherman multitools with a few Victorinox and Shrades thrown in. More recently, I've acquired current versions of the Gerber MP400, MP600, and MP800 and have been pleasantly surprised in many respects.
My most comfortable multitool pliers at the moment are the Crescent ToolZall (aka/Bear Jaws), Super Bear Jaws, and Victorinox Spirit. The Gerber M600 blunt nose seems pretty good, too, but I've not had sufficient experience with it yet.
-
Thanks parnass

Yes, I can see your point on the smaller diameter stuff. In fact whilst my ramblings focus of one perspective of tool use, conversely they might be of benefit for opposite reasons. It might be for example that someone may look at the Octane and decide that grip is way too small for them, and therefore they would find a more splayed grip more efficient for their use. I'm certainly not trying to impose an X is better than Y perspective, but rather trying to highlight a factor which doesn't seem to have gotten much coverage before, an which may help folks get a different perspective (good or bad) on tools they haven't necessarily spent time with before
-
This is an amazingly well thought out post, and I tend to agree with you.
SOG also is able to be used in the closed position, with the handles and head pointed the same way, but I feel the same way about it in that configuration- the handles just open too wide to be of much use.
Def
Sent from my smurfing hunk of techno sorcery
-
I can better appreciate the shape of the Spirit/Swisstool (and normal pliers) now - to prevent hands slipping towards the plier heads. Spring loaded pliers would also help solve this.
I find the Skeletool usable both ways around but a spring would improve it a lot IMO.Are you going to compare with a Wave? I imagine it would be similar to the Surge which I find very comfortable.
-
Adjustable arc joint and slip joint pliers overcome the problem of having the handles too close or too far apart when gripping an item. That's why I often carry a Knipex Cobra pliers.
Incorporating that into a reasonably sized multitool which also has a wire cutter would be interesting.
-
This is my main complaint about the Wingman. The plier handles are wider open than the Wave's by a significant margin so the tool feels too big in the hands during use. That coupled with the spring action and the smooth steel grips means the tool slides backward in your hands during use. None of my other Leathermans seem to suffer that problem.
I must express a dissenting opinion regarding small tools, though. Compare a Squirt to a Dime. The Squirt is a better tool by far. The pliers are much grippier, the wire cutters work, the blade holds an edge, and the bottle opener isn't anywhere near as obnoxious. Only thing I liked about the Dime better was the paint. The Squirt's anodized coating feels much easier to scratch off. They're about equal in scissors; I don't really like the leaf spring design. Maybe if it worked more like a Wingman in that spring tension is removed when the tool is closed, but meh.
-
Great post and interesting comparisons !
-
Thanks for the insight. Honestly, it didn't occur to me to look at that aspect of a MT. I am a very light plier user and mostly its smaller stuff (bending sheet metal on a server housing and such).
Having hands fitting into glove size M I can say I have medium sized hands too (maybe leaning towards the small). So this is definitively something that would affect me coming a day where I need the pliers a lot.It also explains to me the benefit of sliding pliers. I was wondering about that and could primarily see the drawbacks.
Also, up till now, I was wondering why not everybody would copy SOGs power pliers never seeing any disadvantage apart from the added complexity for manufacturing. Maybe I'm not as smart as I thought :D.
Excellent observation, thanks for sharing. -
Thank you all, I really appreciate the comments.

This evening, I will continue where I left off and complete the series of posts as originally planned. After that, I'll address your comments as best I can, and look at taking/uploading additional pics as necessary - including a Wichard multitool with slip joint pliers. I hadn't originally photographed the Wave or Wingman either, so I'll look at those too

-
Great work there.

-
Excellent article 50ft, I look forward to reading the next bit. Thanks for putting the time and effort into this.

-
Very informative, I can see some of your reasons now. thanks.
-
I am going a different route and carry a pair Channel Lock slipjoint pliers with a Crater knife or SAK.
-
Excellent thread Al
I'm in the same boat as you with the average hand size. I hadn't really paid it much attention for the most part until a few months ago. I don't use pliers a lot anyway, and most times, it's not for anything large enough to require a wider grip.It does seem LM is guilty of this quite a bit, with the OHT being the exception from what I've experienced. SOG is horrible with this. That was a big negative for me with the PPP I have. Even though I don't have big hands and don't normally have to grip anything that large, it still felt odd how the handles just continued to splay out with no stop.
-
Continuing on ... :D
Leatherman's handles haven't alwys been as splayed as shown in several of the pics above. In fact when their tools were first introduced, the grip size was a lot friendlier to the more modest hand size than today's offerings. Here is the PST undergoing the same regime.


Of course these were rather uncomfortable tools to bear down on due to the lack of any rolled edges, zytel, or any other handle architecture to spread the load on the hands. That said, even wrapping the handle with a buff, or bandand, or even a shirt sleeve to add some padding, the grip is still more controlable and within the efficiency range for an average sized hand. This is one of the reasons why the older PSTs and Sideclip have crept back into my carry options. I feel the Pulse may be similar in the splay of the handles, but adds the rolled edges for increased comfort. Unfortunately, I just couldn't get on with the locks on that thing at all. In a way Leatherman tools have gradually become less ergonomic as time has passed.
Some would consider these older LM tools to be a more moderate duty plier, and I would consider these next two from Gerber to be moderate duty too.




The MP700 and much maligned BG Strata are much more hand filling than the PST and offer a greatly increased handle comfort. The smooth rounded aluminium scales on the 700 and textured polymer on the Strata offer a very comfortable and secure grip, and in theory should be capable of allowing the user to exert full force against the handles with no discomfort whatsoever .... but there is a problem. If the user starts using these tools for heavy duty applications, the tool itself will suffer for it faster than most.
The reason for this is that both these tools have a hollow plier head which is fitted with a spring return. For delicate tasks the sprung pliers can be a real benefit, and the spring tension is well matched for the size of the tool. It is by no means underwhelming or overbearing, and offers a steady return to the open position, but still allows a good working feel of what you are gripping. Unfortunately, this hollow handle also concentrates the forces onto a smaller area on the main plier pivot itself, and this increases internal wear and reduces the life of the plier. My first MP700 was very smooth to start with, but after some extended usage and a few heavy applications, the pliers developed a bit of slop. This didn't impede the use too much other than the tool wouldn't fully close as the slack that developed in the plier head allowed the handles to come away from each other a bit when the tool was closed. Had these got gone back for warranty on another issue, I could see this increased wear becoming a factor and possibly even taking the tool to failure in time.
The BG Strata gets more of a kicking than it deserves in fairness, purely due to the celebrity branding/endorsement by the guy everyone seem to love to kick. I have used the tool for doing proper work when I had the boat, and the tool did absolutely everything I asked of it with no problems at all. That said, I would say that both these tools are suitable for moderate use on a regular basis, but are capable of the occasional heavier duty use when needed. Just don't use them for heavy duty all the time or you'll seriously reduce the working life of the tool.
Back on the subject of ergonomics though, if you are using these for moderate use, you can use these pliers all day long without the cumulative strain on your hands that you would experience from many other pliers based tools. That again means they are winners in my book. The pliers may take some injury from over exertion or prolongued usage, but your hands won't .... and you can't send your hands off for warranty like you can with these tools. Two very underrated tools for people who don't have to push their pliers to the limit.
-
@Monrogue said:
Excellent thread Al
I'm in the same boat as you with the average hand size. I hadn't really paid it much attention for the most part until a few months ago. I don't use pliers a lot anyway, and most times, it's not for anything large enough to require a wider grip.It does seem LM is guilty of this quite a bit, with the OHT being the exception from what I've experienced. SOG is horrible with this. That was a big negative for me with the PPP I have. Even though I don't have big hands and don't normally have to grip anything that large, it still felt odd how the handles just continued to splay out with no stop.
Even though we all suspected it, I still think it's quite brave of you to talk so openly about it
. -
Excellent thread Al
I'm in the same boat as you with the average hand size. I hadn't really paid it much attention for the most part until a few months ago. I don't use pliers a lot anyway, and most times, it's not for anything large enough to require a wider grip.It does seem LM is guilty of this quite a bit, with the OHT being the exception from what I've experienced. SOG is horrible with this. That was a big negative for me with the PPP I have. Even though I don't have big hands and don't normally have to grip anything that large, it still felt odd how the handles just continued to splay out with no stop.
Even though we all suspected it, I still think it's quite brave of you to talk so openly about it
.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login