One of the reasons I keep picking Gerber over Leatherman ...
-
Great work there.

-
Excellent article 50ft, I look forward to reading the next bit. Thanks for putting the time and effort into this.

-
Very informative, I can see some of your reasons now. thanks.
-
I am going a different route and carry a pair Channel Lock slipjoint pliers with a Crater knife or SAK.
-
Excellent thread Al
I'm in the same boat as you with the average hand size. I hadn't really paid it much attention for the most part until a few months ago. I don't use pliers a lot anyway, and most times, it's not for anything large enough to require a wider grip.It does seem LM is guilty of this quite a bit, with the OHT being the exception from what I've experienced. SOG is horrible with this. That was a big negative for me with the PPP I have. Even though I don't have big hands and don't normally have to grip anything that large, it still felt odd how the handles just continued to splay out with no stop.
-
Continuing on ... :D
Leatherman's handles haven't alwys been as splayed as shown in several of the pics above. In fact when their tools were first introduced, the grip size was a lot friendlier to the more modest hand size than today's offerings. Here is the PST undergoing the same regime.


Of course these were rather uncomfortable tools to bear down on due to the lack of any rolled edges, zytel, or any other handle architecture to spread the load on the hands. That said, even wrapping the handle with a buff, or bandand, or even a shirt sleeve to add some padding, the grip is still more controlable and within the efficiency range for an average sized hand. This is one of the reasons why the older PSTs and Sideclip have crept back into my carry options. I feel the Pulse may be similar in the splay of the handles, but adds the rolled edges for increased comfort. Unfortunately, I just couldn't get on with the locks on that thing at all. In a way Leatherman tools have gradually become less ergonomic as time has passed.
Some would consider these older LM tools to be a more moderate duty plier, and I would consider these next two from Gerber to be moderate duty too.




The MP700 and much maligned BG Strata are much more hand filling than the PST and offer a greatly increased handle comfort. The smooth rounded aluminium scales on the 700 and textured polymer on the Strata offer a very comfortable and secure grip, and in theory should be capable of allowing the user to exert full force against the handles with no discomfort whatsoever .... but there is a problem. If the user starts using these tools for heavy duty applications, the tool itself will suffer for it faster than most.
The reason for this is that both these tools have a hollow plier head which is fitted with a spring return. For delicate tasks the sprung pliers can be a real benefit, and the spring tension is well matched for the size of the tool. It is by no means underwhelming or overbearing, and offers a steady return to the open position, but still allows a good working feel of what you are gripping. Unfortunately, this hollow handle also concentrates the forces onto a smaller area on the main plier pivot itself, and this increases internal wear and reduces the life of the plier. My first MP700 was very smooth to start with, but after some extended usage and a few heavy applications, the pliers developed a bit of slop. This didn't impede the use too much other than the tool wouldn't fully close as the slack that developed in the plier head allowed the handles to come away from each other a bit when the tool was closed. Had these got gone back for warranty on another issue, I could see this increased wear becoming a factor and possibly even taking the tool to failure in time.
The BG Strata gets more of a kicking than it deserves in fairness, purely due to the celebrity branding/endorsement by the guy everyone seem to love to kick. I have used the tool for doing proper work when I had the boat, and the tool did absolutely everything I asked of it with no problems at all. That said, I would say that both these tools are suitable for moderate use on a regular basis, but are capable of the occasional heavier duty use when needed. Just don't use them for heavy duty all the time or you'll seriously reduce the working life of the tool.
Back on the subject of ergonomics though, if you are using these for moderate use, you can use these pliers all day long without the cumulative strain on your hands that you would experience from many other pliers based tools. That again means they are winners in my book. The pliers may take some injury from over exertion or prolongued usage, but your hands won't .... and you can't send your hands off for warranty like you can with these tools. Two very underrated tools for people who don't have to push their pliers to the limit.
-
@Monrogue said:
Excellent thread Al
I'm in the same boat as you with the average hand size. I hadn't really paid it much attention for the most part until a few months ago. I don't use pliers a lot anyway, and most times, it's not for anything large enough to require a wider grip.It does seem LM is guilty of this quite a bit, with the OHT being the exception from what I've experienced. SOG is horrible with this. That was a big negative for me with the PPP I have. Even though I don't have big hands and don't normally have to grip anything that large, it still felt odd how the handles just continued to splay out with no stop.
Even though we all suspected it, I still think it's quite brave of you to talk so openly about it
. -
Excellent thread Al
I'm in the same boat as you with the average hand size. I hadn't really paid it much attention for the most part until a few months ago. I don't use pliers a lot anyway, and most times, it's not for anything large enough to require a wider grip.It does seem LM is guilty of this quite a bit, with the OHT being the exception from what I've experienced. SOG is horrible with this. That was a big negative for me with the PPP I have. Even though I don't have big hands and don't normally have to grip anything that large, it still felt odd how the handles just continued to splay out with no stop.
Even though we all suspected it, I still think it's quite brave of you to talk so openly about it
.
-
Excellent thread Al
I'm in the same boat as you with the average hand size. I hadn't really paid it much attention for the most part until a few months ago. I don't use pliers a lot anyway, and most times, it's not for anything large enough to require a wider grip.It does seem LM is guilty of this quite a bit, with the OHT being the exception from what I've experienced. SOG is horrible with this. That was a big negative for me with the PPP I have. Even though I don't have big hands and don't normally have to grip anything that large, it still felt odd how the handles just continued to splay out with no stop.
Even though we all suspected it, I still think it's quite brave of you to talk so openly about it
.
Oh man, I really set myself up for that one huh? I didn't even realize it either
-
And finally .... The one that really surprised me.
I only discovered the real star of the show in respect of pliers ergonomics fairly recently, and even so it wasn't until I started putting this comparison together (or at least preparing for it) that I really noticed just how good these pliers really were in comparison to it's competitors in terms of ergonomics. Some of you will not be happy about this though.
It's a Gerber ....
... and it's a Chinese made one at that ....
Ignore all those purile "Chinese garbage" stereotypes though, just put all your prejudices aside for a moment, and take a look why for me the Gerber Diesel is probably "best in class" of all the 4.1/2" framed pliers based multitools when it comes to comfort and control when using the pliers


The longer wire cutters move the main gripping area forward, meaning the pliers don't need to open as wide to grip something the same size, and the handles start from a sensible position too. Added together the Gerber Diesel offers better control and ergonomics not just over it's 4.1/2" competition, but also many tools in the 4" frame size too.
For a direct comparison of the frame size, let's pull back up the photos of the Swisstool and ST300 from the beginning of this thread ...


As you can clearly see there is a massive difference in the control and comfort of these tools. In fact I probably have more purchase on the Diesel handles when gripping a 17.5mm diameter object, than I do on the Swisstool and ST300 when they are in the CLOSED position ...


Obviously this is merely one factor of this particular tool. Some people may absolutely have to have the indexable cutters of the ST300, or the pry capabilities of the Swisstool, or the reach of the screwdrivers of either tool - but when it comes to using your pliers for applying gripping force and your hands not feeling like a tank has run over them by the end of the day, the Diesel here is a big winner. Here is a full framed multitool which actually allows the user to harness the full potential from the tool's pliers.
The hand is working well within the efficiency range, the forces from the hand are applied effectively and efficietly to the handle, the load is spread comfortable everywhere is contacts the hand, it's not pinchy, there's minimal hotspots .... why the bloody hell can't anyone else make tools like this? For the fans of the MP600, this close relative also offers a woodsaw (absent from all other models), and the drivers (albeit no full 3D Phillips) offer a bit better length than the MP600. It kind of leaves me wondering not just why other companies aren't making tools this ergonomic, but why it took me so long to zone in on this tool and realise that a solution to the problem of the "legs akimbo" handle trend was already out there.
To be honest, I only really discovered this gem after the fate of the boat had been sealed, and so I haven't had to use this in the heavier applications that I had to subject other tools to. In all honesty I don't know how durable the teeth on the pliers are. I don't know how durable the wire cutters are ... though there is no hard wire notch provided, so I suspect these might be easily damaged in hard wire cutting, especially considering the acute edge geometry. That said, this is still a tool I am really glad to have bought to try, and one that I hope will serve me for a long time because I know my hands will be subject to far less wear and tear as a result of using them over more expensive alternatives. It might not be the best tool for every job out there, but I have every confidence I will get good service from it
Thanks for bearing with me this long through my rambling. Hope it was worth it :D

-
You gave us very good points here. Good reading, thank you.
-
Great job ! I'm sure this will be very helpful for people

Maybe you could have the title of the thread Include "Comparisons of handle spread of various pliers in multi tools" so someone searching for this info could find it easier.
-
I had considered the Diesel way back when I was debating what Gerber MT to get for my second one. Now you're making me want to get one just to check it out >:D
-
This is a great overview

-
@parnass said:
Excellent series of posts, 50ft-trad. I concur with several points concerning the ease of using Gerber vs. non-Gerber pliers, but I think the majority of your analysis addresses gripping larger objects.For me, the Gerber MP400 and MP600 series don't do as well as the competition when gripping small objects. In that case, I find their handles are too close together. They are so close together that it's difficult to keep a finger in between, a technique I use to better control the gripping action of smaller objects. Perhaps spring loading the pliers would help there.
While most people sing the praises of the Leatherman Wave, the sharp top edges of the handles and tools chafe my palms when using the pliers. Plus, the knife spine can pinch my palm sometimes when using the pliers. I had the same chafing problem with the Surge (and it was just too big and heavy).
The Skeletool pliers has drawbacks, too. The asymmetric handles restrict you to holding them in only one position instead of two, and the curvature of the bottom handle forces my hand to slide towards the plier head.
I had a bad pinching experience with the original Gerber Multi Pliers several years ago. That led to using a long succession of Leatherman multitools with a few Victorinox and Shrades thrown in. More recently, I've acquired current versions of the Gerber MP400, MP600, and MP800 and have been pleasantly surprised in many respects.
My most comfortable multitool pliers at the moment are the Crescent ToolZall (aka/Bear Jaws), Super Bear Jaws, and Victorinox Spirit. The Gerber M600 blunt nose seems pretty good, too, but I've not had sufficient experience with it yet.
Just revisiting this post again, as I didn't pay it full attention before ...
The Skeletool is actually a tool which doesn't suffer from the handle splay as found on so many other Leatherman models. For me it is a tool which suffers a host of other problems instead. The concave handle is quite slim and there is very little spread of load across the fingers, which means the gripping force is focussed in a small area. I also find that my fingers end up uncomfortably scrunched together and instead of force being transmitted to the handle, most of it just coes into contorting your hand. The spiky lump on the convex side doesn't help matters either. It's a fantastic example of how NOT to design plier handles in my opinion.
You are right, the Ye Olde Mr Pinchy was another great example of "what not to do". I think the tool I sold to Gareth was in my posession for less than 15 minutes before I decided I had to get rid of it. What a nasty bitey vindictive piece of equipment. As soon as I picked it up it bit me, and then once I'd looked at the tools inside and closed it up, it bit me again ... and didn't stop biting me until I put the bloody thing down :ahhh Evil!
The original Bear Jaws tool I had was very good for comfort, but I ended up letting those go in favour of a more refined toolset. Whilst the handles were very comfortable, I just felt the tools were just a little too agricultural. They did the job, but it wasn't everyday user material when thre were so many other options that weren't as clunky.
As to sprung pliers, the Strata might be worth a try for you if you don't use your pliers too hard, but please do note my comments on the hollow plier head. I know Tom (Jerseydevil) is a big fan of the Strata and I believe it's one of his primary multitools. When he gets back he'll be able to give you a better insight than I can (the standard Strata is also very slightly different to the BG variant)
-
Thanks guys
I really appreciate the comments 
-
I do not own one to check with, but the OHT might be closer to the gerber when it comes to handle seperation. (since they basically used Gerber's design concepts)
I checked, you are right about that
Any chance you could offer up any comparison pics with one of the other tools that I have shown? Obviously your hands will be different to mine, but if there's a "like for like" shot with one of the tools I've covered, we should get a good enough idea of how it compares

-
@Grant Lamontagne said:
This is an amazingly well thought out post, and I tend to agree with you.SOG also is able to be used in the closed position, with the handles and head pointed the same way, but I feel the same way about it in that configuration- the handles just open too wide to be of much use.
Def
Sent from my smurfing hunk of techno sorcery
Thanks Grant

I agree on the "head inwards" configuration too. In fact that way, you might be able to get a bit of gripping force, but no leverage to turn/pull/twist or do anything with it.
Considering how bad the ergonomics are on the "Power" range of tools (particularly those with exposed "gears of madness", it's quite surprising how good the ergonomics were on some of their other tools. The Toolclip looks like it should be a bloody horrible tool to use, but is surprisingly comfortable and robust too. As for the Switchplier, that has got to be the best multitool EVER when used as a screwdriver. Mine has the bit adaptor (as you know ;)) and I don't think there's another multitool that I have owned that has come anywhere close to being as comfortable in "driver mode". It's just a humongous shame that the pliers are so flawed in their strength/integrity due to that pathetic little cast noggin taking all the load
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login