Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Common "Flicky-Plier" Problem?

Scheduled Pinned Locked Moved Gerber Tools
19 Posts 1 Posters 2.6k Views
  1. Home
  2. Tool Talk
  3. Gerber Tools
  4. Common "Flicky-Plier" Problem?
Common "Flicky-Plier" Problem?
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • rdub934 Offline
    rdub934
    Posts: 1,991
    rdub934 Offline
    rdub934
    wrote on last edited by
    Quote Reply

      I am not sure how to best describe this so I will just dive in.

      On my MP400 and Octane, after having to bear down pretty heavily (ok, not too heavily for the Octane), the pliers do not open effortlessly anymore. I am not talking about the deployment of the pliers, as they still snap out the same as they ever have. What I am referring to is the actual opening of the jaws. It is almost as if for the first 10% of the range of movement, that a brake is being applied. I can detect no grinding, there is no grittiness to the motion, they just take actual effort to open, as opposed to before, when I could hold the tool horizontally by only the top handle and the bottom handle would fall away allowing the jaws to open. I have cleaned and re-oiled both tools but they both still do it. :shrug:

      Confusingly enough, occasionally, the MP400 will be good to go again, the problem seemingly corrected on its own. Only for it to start happening again the next time I deploy the pliers. :think:

      I am curious if anyone else has noticed a similar occurrence in their own tools or knows what causes this (I know heavy use, but I mean what is the physical cause of the binding). When it was just my MP400 I didn't think anything of it and just assumed it was specific to my tool or a result of using it to hard, but when it again happened to my Octane I am now wondering if all front deploy Gerbers are prone to this problem.

      1 Reply Last reply
      • NKlamerus Offline
        NKlamerus
        Posts: 4,767
        NKlamerus Offline
        NKlamerus
        wrote on last edited by
        #1 Quote Reply

          Have you tried twisting/angling the handles to see if that makes a difference?

          1 Reply Last reply
          • AimlessWanderer Offline
            AimlessWanderer
            Posts: 17,518
            AimlessWanderer Offline
            AimlessWanderer
            wrote on last edited by
            #2 Quote Reply

              I can't recall ever experiencing that on any of mine ... :think:

              When you were bearing down heavily on them, were you wire cutting? Is there any deformation there that might be causing them to stick? If yo a quick tidy up with a file might fix it :tu:

              1 Reply Last reply
              • rdub934 Offline
                rdub934
                Posts: 1,991
                rdub934 Offline
                rdub934
                wrote on last edited by
                #3 Quote Reply

                  NKlamerus, I have tried angling the handles and sort of twisting them and it doesn't seem to make any difference.

                  50ft-trad, I was not wire cutting. Just needing to get a grip on something, I can't recall specifically. In the case of the Octane, I was twisting fence clips around a chain-link fence, not really putting much pressure on them at all. Also, the Octane has anvil style cutters so damage to the cutters wouldn't affect the plier operation.

                  1 Reply Last reply
                  • AimlessWanderer Offline
                    AimlessWanderer
                    Posts: 17,518
                    AimlessWanderer Offline
                    AimlessWanderer
                    wrote on last edited by
                    #4 Quote Reply

                      It was just a thought ... :shrug:

                      If I think of anything else, I'll let you know :tu:

                      1 Reply Last reply
                      • NKlamerus Offline
                        NKlamerus
                        Posts: 4,767
                        NKlamerus Offline
                        NKlamerus
                        wrote on last edited by
                        #5 Quote Reply

                          Have you ever cleaned or oiled them?

                          1 Reply Last reply
                          • rdub934 Offline
                            rdub934
                            Posts: 1,991
                            rdub934 Offline
                            rdub934
                            wrote on last edited by
                            #6 Quote Reply

                              Thanks, trad.

                              I have cleaned and re-oiled them. It made no difference.

                              Really, the only thing I can imagine is that maybe the pivot area got damaged slightly, or the pivot (rivet?) itself. Like, maybe the hole got slightly warped around the rivet. Is that even possible? Seems hard to imagine that happening just from applying squeezing force to the handles.

                              1 Reply Last reply
                              • ducttapetech Offline
                                ducttapetech
                                Posts: 18,707
                                ducttapetech Offline
                                ducttapetech
                                wrote on last edited by
                                #7 Quote Reply

                                  I had a MP 600 do this to me. Never did really figure out what it was. Over time it did correct itself. I think it might have been a burr in the pivot itself.

                                  Nate

                                  1 Reply Last reply
                                  • gregozedobe Offline
                                    gregozedobe
                                    Posts: 5,148
                                    gregozedobe Offline
                                    gregozedobe
                                    wrote on last edited by
                                    #8 Quote Reply

                                      I have a vague recollection of someone here on MTo describing the same problem with a LM tool. Couldt be either a bit of grit/gunge inside the plier pivot or a slight deformation that binds after harder squeezing on the handles to grip something tightly. Unfortunately there is no non-destructive way to investigate problems inside peened plier pivots.

                                      1 Reply Last reply
                                      • lowtech Offline
                                        lowtech
                                        Posts: 4,799
                                        lowtech Offline
                                        lowtech
                                        wrote on last edited by
                                        #9 Quote Reply

                                          @ducttapetech said:
                                          I had a MP 600 do this to me. Never did really figure out what it was. Over time it did correct itself. I think it might have been a burr in the pivot itself.

                                          Nate

                                          I did experience this on a MP 600, too. My EDC MP 600 did not ever do it, no matter how hard I use it. I believe it might be a comnbination of the axis of the plier head and plier handle not being congruent and the plier head being a bit stiff, I have no real explanation, just wanted to emntion I experienced that ,too.

                                          1 Reply Last reply
                                          • rdub934 Offline
                                            rdub934
                                            Posts: 1,991
                                            rdub934 Offline
                                            rdub934
                                            wrote on last edited by
                                            #10 Quote Reply

                                              Thanks for the input, folks. I think I agree lowtech, maybe since most Gerbers are "rattly" they are more prone to this sort of malfunction since the pliers are able to be at slightly different angle than the handles. I never really saw the looseness of Gerbers being a real problem just a personal preference type of deal, but maybe this is one reason in favor of tighter tolerances as found on Leathermans.

                                              I wonder if this is as common of a problem on the tools from other companies?

                                              1 Reply Last reply
                                              • Dunc Offline
                                                Dunc
                                                Admin Team
                                                Posts: 11,308
                                                Dunc Offline
                                                Dunc
                                                Admin Team
                                                wrote on last edited by
                                                #11 Quote Reply

                                                  I've had a fair few MP400's and I've seen this problem on one of them. It seemed to be caused by the pivot. After gripping down hard on something with the pliers a certain percentage of the opening of the jaws was stiff. Continuis open and closing returned the pliers to normal feel until you gripped something tight again.

                                                  1 Reply Last reply
                                                  • tattoosteve99 Offline
                                                    tattoosteve99
                                                    Posts: 6,326
                                                    tattoosteve99 Offline
                                                    tattoosteve99
                                                    wrote on last edited by
                                                    #12 Quote Reply

                                                      Take a regular graphite pencil and rub over the pivot area. Apply some oil or whatever. Do this a couple times and work it in good. Should work

                                                      1 Reply Last reply
                                                      • PTRSAK Offline
                                                        PTRSAK
                                                        Posts: 4,776
                                                        PTRSAK Offline
                                                        PTRSAK
                                                        wrote on last edited by
                                                        #13 Quote Reply

                                                          My MP400 has this problem, I first thought of a burr on the wire cutters but upon examination there is none but that's how it feels. after that first movement the pliers move freely.
                                                          Most annoying.

                                                          1 Reply Last reply
                                                          • neillcurrie Offline
                                                            neillcurrie
                                                            Posts: 860
                                                            neillcurrie Offline
                                                            neillcurrie
                                                            wrote on last edited by
                                                            #14 Quote Reply

                                                              I had it happen with a MP600. I looked at it carefully to see where in the arc of closing the pliers it happened, and it was just when the wire cutter faces moved across each other.
                                                              Though there was no apparent damage to either wire cutter, I carefully flattened the faces with a diamond flat rod, until they just passed cleanly.
                                                              End of problem in my case.
                                                              BTW, you can buy small tubes of graphite almost any place that cuts keys. I've never actually used mine, but it's supposed to be a good dry lubricant, that doesn't hold onto pocket lint, etc.

                                                              1 Reply Last reply
                                                              • David Offline
                                                                David
                                                                Posts: 9,246
                                                                David Offline
                                                                David
                                                                wrote on last edited by
                                                                #15 Quote Reply

                                                                  As others I've had this problem on the MP600 after hard gripping.

                                                                  @neillcurrie said:
                                                                  I had it happen with a MP600. I looked at it carefully to see where in the arc of closing the pliers it happened, and it was just when the wire cutter faces moved across each other.
                                                                  Though there was no apparent damage to either wire cutter, **I carefully flattened the faces with a diamond flat rod, until they just passed cleanly.
                                                                  End of problem in my case.**BTW, you can buy small tubes of graphite almost any place that cuts keys. I've never actually used mine, but it's supposed to be a good dry lubricant, that doesn't hold onto pocket lint, etc.

                                                                  Thanks for the tip. :tu:

                                                                  1 Reply Last reply
                                                                  • rdub934 Offline
                                                                    rdub934
                                                                    Posts: 1,991
                                                                    rdub934 Offline
                                                                    rdub934
                                                                    wrote on last edited by
                                                                    #16 Quote Reply

                                                                      I definitely do not have any burs, nicks, or dents in my cutters - the Octane is anvil-style cutters so even if they were damaged, it would not be causing this issue. Strangely, I have discovered that my MP400 seems to be mostly good to go these days. Only about 1 in 20 times that I deploy the pliers do they exhibit any stickiness. The Octane is still sticky basically all the time, but it is not as bad as it had been - the pliers are much more usable now than they were previously.

                                                                      1 Reply Last reply
                                                                      • Freaver Offline
                                                                        Freaver
                                                                        Posts: 629
                                                                        Freaver Offline
                                                                        Freaver
                                                                        wrote on last edited by
                                                                        #17 Quote Reply

                                                                          @David said:
                                                                          As others I've had this problem on the MP600 after hard gripping.

                                                                          @neillcurrie said:

                                                                          I had it happen with a MP600. I looked at it carefully to see where in the arc of closing the pliers it happened, and it was just when the wire cutter faces moved across each other.
                                                                          Though there was no apparent damage to either wire cutter, **I carefully flattened the faces with a diamond flat rod, until they just passed cleanly.
                                                                          End of problem in my case.**BTW, you can buy small tubes of graphite almost any place that cuts keys. I've never actually used mine, but it's supposed to be a good dry lubricant, that doesn't hold onto pocket lint, etc.

                                                                          Thanks for the tip. :tu:

                                                                          +1. Except I've had this problem since I got my MP600 secondhand - it was in a not too pretty state, so the previous owner might have been a bit rough on it. Gotta try that trick with a diamond rod or file, when I get the chance.

                                                                          1 Reply Last reply
                                                                          • Cupboard Offline
                                                                            Cupboard
                                                                            Posts: 2,018
                                                                            Cupboard Offline
                                                                            Cupboard
                                                                            wrote on last edited by
                                                                            #18 Quote Reply

                                                                              @gregozedobe said:
                                                                              I have a vague recollection of someone here on MTo describing the same problem with a LM tool. Couldt be either a bit of grit/gunge inside the plier pivot or a slight deformation that binds after harder squeezing on the handles to grip something tightly. Unfortunately there is no non-destructive way to investigate problems inside peened plier pivots.

                                                                              Yes, it's a known problem on the Rebar, particularly when fairly new.
                                                                              I had one develop it after about a month of use, but then it cleared after about 6 months. You'd apply a lot of force to it then the pivot would seize up.

                                                                              1 Reply Last reply

                                                                              Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                                              Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                                              With your input, this post could be even better 💗

                                                                              Register Login

                                                                              1. Home
                                                                              2. Tool Talk
                                                                              3. Gerber Tools
                                                                              4. Common "Flicky-Plier" Problem?
                                                                              Reply
                                                                              • Reply as topic
                                                                              Log in to reply
                                                                              COMMUNITY LINKS
                                                                              EDC-TV SAKWiki GearFeed SAKSelector
                                                                              Operational Funds

                                                                              Help us keep the Unworkable working!

                                                                              Make A Donation
                                                                              November Goal: $300.00
                                                                              Due Date: Nov 30
                                                                              Total Receipts: $0.00
                                                                              Below Goal: $300.00
                                                                              0% funded
                                                                              • Login

                                                                              • Don't have an account? Register

                                                                              • Login or register to search.
                                                                              • First post
                                                                                Last post
                                                                              0