Weapons centric multi-tools.
-
I hear you. It would make a neat little EDC.
-
Another great post Chako!! I also have the OTIS with the BO Gerber. Great stuff!
-
Smith and Wesson Universal Armorer Tool.
Here is something a little different, and a tool I just received today. Before we begin, Smith and Wesson tools are made by Taylor Brand LLC. I tend to not have high expectations when it comes to Taylor Brand products, but I guess in this instance, I was pleasantly surprised at the quality. Mind you, it is a rather simple tool to begin with.
The S&W Universal Armorer Tool is basically a very large pen like tool in which both ends unscrew, revealing a set of pin and punches required to work on a variety of weapons. The design eerily looks like a beefed up Multitasker Tube, which I can easily speculate might be the inspiration for this tool.
Apparently, there are two models out there. One is geared towards military and police folks, and features duplicate tools. That one is called model SWMPGT1. That tool has the following tools in duplicates:
1/16" Allen Wrench
1/8" Roll Tip Punch Pin
1/16" Flat Tip Punch Pin
M&P Slave Pin
1/16" Brass Flat Tip Punch PinThe Universal Armorer Tool carries the model designation SWUAT1, and has the following tools:
1/16" Allen Wrench
1/16" Roll Tip Punch Pin
1/8" Roll Tip Punch Pin
1/16" Flat Tip Punch Pin
1/8" Flat Tip Punch Pin
MS&W Slave Pin
1/8" Solid Punch Pin
1/8" Brass Flat Tip Punch Pin
1/8" Brass Roll Tip Punch Pin
1/32" Cut Tip Punch Pin
1/16" Cut Tip Punch Pin
1/8" Cut Tip Punch PinI went with the Universal one because I like variety.
The box looks like standard S&W gear.
One end of which carries the model number.
Once opened, there is no doubt that this is a Taylor Brands LLC product.
The MOLLE compliant sheath isn't all that bad. It features the S&W logo on the front flap.
Opening up the sheath, you are greeted with one fat pen looking tool, in a single compartment. The Velcro closure is on a big elastic. Not sure why, but I guess you could probably hand something there, like say, a small hammer, and still be able to close the flap.

And this is the tool.
Both ends unscrew around a center piece. On each end of that center piece is a round rubber piece with holes for the various tools.
Taylor Brands LLC sure loves the S&W logo.
On the tapered end of the tool, is a hole with a magnet at its base. The various punches and pins slide into the hole and are held in place via that magnet.
A close up of some of the tools.
And a look at both ends.
Summary:
Pro:
- A good assortment of pins and punches.
- Everything is self contained.
- Not bad construction in the aluminum body and threaded areas.
- Inclusion of a pocket clip or belt sheath.
Cons:
- Magnet could be stronger. Some of the pins and punches appear to be not very magnetic to begin with (the gold toned ones).
- Multi-tool dedicated at dis-assembly and assembly of firearms.
- Needs other tools to properly use this tool, such as a small mallet.
-
Comes in, looks around, wipes the dust off, exits. :D
-
-
Also, and this is just an idea...
Could you post a gargantuamly sized pictures of those tools ordered by Size, maybe with a Wave inbetween. You know, something like this:

-
Now that would be some time consuming work.
-
-
@Chako said:
SOG Powerlock EOD 2.0.I had forgotten I had this tool. A regular Powerlock with the addition of a C4 spike. Not as good as other EOD efforts by other companies, especially when viewed from the standpoint that no fuse cap crimper is included as a function of the pliers.
A closer look at the C4 spike.
Compound leverage pliers are a SOG specialty.
Yes, being an older version, it has piano hinge locking levers.
Summary:
Pro:
- SOG compound leverage pliers.
- Good quality throughout.
Cons:
- Piano hinge locking levers are a pain to use. They replaced these on the newer versions with a single larger lever.
- No Cap crimper functionality as seen on the Gerber and Leathermans.
- No 8/32 threading to mesh with cleaning kits.
[Aleph78 USES THREAD NECRO]
[IT'S SUPER EFFECTIVE!]
Just had a look at my BO Powerlock EOD and was thinking, isn't that a cap crimper right under the plier head?
-
@Aleph78 said:
SOG Powerlock EOD 2.0.
I had forgotten I had this tool. A regular Powerlock with the addition of a C4 spike. Not as good as other EOD efforts by other companies, especially when viewed from the standpoint that no fuse cap crimper is included as a function of the pliers.
A closer look at the C4 spike.
Compound leverage pliers are a SOG specialty.
Yes, being an older version, it has piano hinge locking levers.
Summary:
Pro:
- SOG compound leverage pliers.
- Good quality throughout.
Cons:
- Piano hinge locking levers are a pain to use. They replaced these on the newer versions with a single larger lever.
- No Cap crimper functionality as seen on the Gerber and Leathermans.
- No 8/32 threading to mesh with cleaning kits.
[Aleph78 USES THREAD NECRO]
[IT'S SUPER EFFECTIVE!]
Just had a look at my BO Powerlock EOD and was thinking, isn't that a cap crimper right under the plier head?
I believe it is and I think it's mentioned on their site and that all their larger tools have them, not only the EOD.
-
That is correct. Looks like I forgot about that when I posted this a year or so ago.
-
That is a neat feature I never knew about that SOG had

-
@Chako said:
Beretta Shotgun Tool.The Beretta shotgun tool is a bit unique in the design department in that its main function is that of a hammer. The sheath is rather well done with the Beretta design on the flap.
Opening the sheath, you can see that there is a side pouch with a rather professional and full sized pin punch. The Beretta Shot gun Tool doesn't pull any punches here.
Yes, that is a very nice pin punch, and with that hammer, I bet you can probably encourage any pin with the gentleness it requires.
You can tell it is from Beretta.
This multi-tool turns into a full sized hammer.
The Beretta Shotgun Tool offers 11 tools for the care and maintenance of your Beretta shotgun. Gunsmith-designed.
·Optima, mobil & victory enhanced choke tool
·Hammer head
·Sheep's foot blade
·2mm punch pin
·Nylon belt sheath
·28-.410 chocke wrench
·12-20 gauge choke wrench
·#2 phillips screwdriver
·Small Pliers
·Flat screwdriver
·Fine FileSummary:
Pro:
- Unique hammer based tool.
- Designed for the folks who like to fiddle with their tools.
- Well finished quality piece of kit.
Cons:
- No 8/32" threading for attachments.
- No locking tools.
What a thread!
Beautiful pics and write-ups. And so many companies and unique tools! 
That hammer tool is amazing. :o
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login























