Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

PVC Foamboard

Scheduled Pinned Locked Moved The Break Room
6 Posts 1 Posters 637 Views
  1. Home
  2. Non Tool Forum
  3. The Break Room
  4. PVC Foamboard
PVC Foamboard
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • Cupboard Offline
    Cupboard
    Posts: 2,018
    Cupboard Offline
    Cupboard
    wrote on last edited by
    Quote Reply

      Also known by the brand Foamex.

      This is yet another material I'd never heard of until last week when I was looking for something else. I bought a small sheet of 5mm board to try for a job I'm doing from here: http://www.ebay.co.uk/itm/261520898848 - note that buying an A4 sheet is a really expensive way to do it, but makes sense as a trial and I'm glad I did. An 8ft*4ft sheet of the 3mm stuff costs £17.50 (around 25USD).

      This might be one of those things that everyone else knows about and uses all the time but if you haven't, it seems like fantastic stuff. The job I'm trying to do is the line the roof of my Land Rover. The Hard Top (van) versions come as just bear aluminium with no lining or anything, and you can buy headlinings for them but they're around the £500 mark and I have better things to spend my money on than that. My plan is to line the roof with soundproofer and insulation then cover it with something to provide a protective surface and finish it off neatly. The "normal" way of doing that is to line it with ply, but either that leave bear wood which I think looks a bit tacky, or you carpet it which is something that accumulates muck and is usually black/grey so it's dark.

      The 5mm foam sheet I've bought is incredibly tough. I cut a 35mm strip off it (either saw it or score it multiple times with a knife and snap) and even that took a lot of force before it finally collapsed when I tried to bend it. You can cut it, shave it, drill it - I tried heating a bit with a hot air gun and got a handy L shaped bit that set solidly. I have now broken that by trying to bend it back with no heat so it's not infallible, but it took a lot of force.
      I've laid in to it with the pliers on my Wave and you can dent it, but it's still rigid and you don't get any splinters or anything. Add to that it seems like really good insulation, water runs off it, it doesn't rattle and it's really light, I can't see why it's not used more. It just seems brilliant.

      I'm now going to buy a small section of 3mm to see if I can bend it round the roof, and if that works I'll buy a load of it. I might even get a section of the thick stuff to cover the floor.

      Have I just discovered something that everyone already knows about? Am I actually missing out on something even better? Thoughts and comments appreciated :)

      1 Reply Last reply
      • Steinar Offline
        Steinar
        Posts: 3,435
        Steinar Offline
        Steinar
        wrote on last edited by
        #1 Quote Reply

          Disclaimer: I will now talk about something I don't know smurf about.

          My first thought is that it might not be very popular in cars because PVC may give off nasty fumes when burning, IIRC. One of the main applications of kydex is plane interiors, and one of the reasons is that its fumes when burning are relatively safe compared to other options.

          I hope someone with a little bit of materials science background can chime in...

          1 Reply Last reply
          • Cupboard Offline
            Cupboard
            Posts: 2,018
            Cupboard Offline
            Cupboard
            wrote on last edited by
            #2 Quote Reply

              I've just tried to set fire to it and nothing very exciting happened. If I held a lighter to the edge I could get it to burn but it went out as soon as I took the lighter away. In the middle it was a struggle to get it to do anything.

              I was outside though which might not have helped. Either way, I wouldn't be worried about having it inside my vehicle.

              1 Reply Last reply
              • Steinar Offline
                Steinar
                Posts: 3,435
                Steinar Offline
                Steinar
                wrote on last edited by
                #3 Quote Reply

                  MT.o in a nutshell:

                  Person 1: It isn't like I know anything about this, but perhaps it produces toxic gases when it burns?

                  Person 2: Good point! I'll try to light it on fire!

                  :rofl:

                  1 Reply Last reply
                  • gregozedobe Offline
                    gregozedobe
                    Posts: 5,148
                    gregozedobe Offline
                    gregozedobe
                    wrote on last edited by
                    #4 Quote Reply

                      @Steinar said:
                      MT.o in a nutshell:

                      Person 1: It isn't like I know anything about this, but perhaps it produces toxic gases when it burns?

                      Person 2: Good point! I'll try to light it on fire!

                      :rofl:

                      I always value empirical evidence over theoretical analysis - that way I know someone has actually tried whatever it is :tu:

                      1 Reply Last reply
                      • Crow Offline
                        Crow
                        Posts: 2,525
                        Crow Offline
                        Crow
                        wrote on last edited by
                        #5 Quote Reply

                          :D like the fact that you tried to make it burn. I like fire >:D Might be my work related stuff... :D

                          There is more material in your car, that will work as your lighter did, and those materials will not go out so easy...

                          Merit Badges
                          Flashlight Paracord BO Tools Level 1 Time Lord Level 3 Axe User Outdoor Cook
                          1 Reply Last reply

                          Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                          Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                          With your input, this post could be even better 💗

                          Register Login

                          1. Home
                          2. Non Tool Forum
                          3. The Break Room
                          4. PVC Foamboard
                          Reply
                          • Reply as topic
                          Log in to reply
                          COMMUNITY LINKS
                          EDC-TV SAKWiki GearFeed SAKSelector
                          Operational Funds

                          Help us keep the Unworkable working!

                          Make A Donation
                          November Goal: $300.00
                          Due Date: Nov 30
                          Total Receipts: $0.00
                          Below Goal: $300.00
                          0% funded
                          • Login

                          • Don't have an account? Register

                          • Login or register to search.
                          • First post
                            Last post
                          0