New SOG multis?
-
Still, though, this probably matches up comparably to other light duty, pocket-carry tools such as the Gerber Balance or Octane, or the Leatherman Skeletool (which is known to fail if used for heavy tasks).
-
That is exactly my question. How bad is it? I mean the last task my pliers had to fulfill was shortening wooden skewers to the shashlik would fit into my frying pan :D
-
@rdub934 said:
Still, though, this probably matches up comparably to other light duty, pocket-carry tools such as the Gerber Balance or Octane, or the Leatherman Skeletool (which is known to fail if used for heavy tasks).Not even close!
Look at the Skele, Balance and Octane, and how these forces are transmitted to the head. The go back to the pic above. Remember that pathetic little pin is only on one side of the head. Think how wire cutters are sited very close to the pivot to be most effective, well that pin is even nearer and so subjected to more force, is only in a cast material (not usually good with tensile or shear forces), and will gradually weaken with every use. Having never broken my original Switchplier (because I don't use it), I can't be more definitive in what the breaking point is ...
At a guess, I'd say Dime would be a nearer comparison, because if you overload those the backspring buckles - but remember you are trying to stay at that level of duty on a fuller sized tool where it's very easy to apply that little bit too much force
-
I love the looks of the new switch pliers.
It's to bad it won't be a quality tool.
-
If its the same cast pin design and it breaks, I'll drill it out and replace it with a hardened steel dowel pin. :D
-
@Ombudsman said:
Just checked the Patents for the Switchplier:Hand tool with retractable jaws US 5829329
Hand tool with retractable jaw assembly US 5957013
And is not being referenced recently by SOG [emoji14]
So you must be right Trad ! They didn't do anything to improve the mechanism.

That says 1998. I wonder if there the same now?
Nate
-
Just checked the Patents for the Switchplier:
Hand tool with retractable jaws US 5829329
Hand tool with retractable jaw assembly US 5957013
And is not being referenced recently by SOG [emoji14]
So you must be right Trad ! They didn't do anything to improve the mechanism.

That says 1998. I wonder if there the same now?
Nate
http://www.trademarkia.com/switchplier-75714205.html
I bet it is the same. Tradmarkia page for SwitchPlier - filed in 1999, but check this out, "REGISTERED AND RENEWED
3/16/2011". Have they been sitting on a re-release for 4 years? Lol -
@Syph007 said:
If its the same cast pin design and it breaks, I'll drill it out and replace it with a hardened steel dowel pin. :DOk I'm totally ignorant when it comes to steel and such. But I conclude from the above, that the pin would hold if done from hardened steel, right? Now check the design again. Unlike the images of the Switchplier the pin is not part of the plier-head. So, maybe the original design was good, but they changed it when it came into production to save money. So, if I understand this correct, all we have to hope for is that they don't jump hoops and make it correct this time.
-
If its the same cast pin design and it breaks, I'll drill it out and replace it with a hardened steel dowel pin. :D
Ok I'm totally ignorant when it comes to steel and such. But I conclude from the above, that the pin would hold if done from hardened steel, right? Now check the design again. Unlike the images of the Switchplier the pin is not part of the plier-head. So, maybe the original design was good, but they changed it when it came into production to save money. So, if I understand this correct, all we have to hope for is that they don't jump hoops and make it correct this time.
Yep most folders used hardened steel stop pins in construction and those take alot of shear force, so its totally doable. I understand the convenience of having them cast as part of the plier head but that is a very weak design and Id be shocked if they repeated it blindly to have the same failure rate. That would just be absurd.
Im excited to get one and take it apart though! :D
-
I want one.
-
@ducttapetech said:
Hand tool with retractable jaw assembly US 5957013
That says 1998
Nate
Yet for some reason it reminds me of 1898

-
Did the Wright Brohers draw that??
-
Pre-order on knife center for $43.95. I like that price a lot more than the $65 msrp
http://www.knifecenter.com/item/SOGSWP1001/sog-swp1001-switchplier-20-multi-tool-black-and-silver
-
The price worries me a bit actually. Thats less that a power duo, and we all know what kind of quality processes those were constructed with. I'll still buy one though. :D
-
@Syph007 said:
The price worries me a bit actually. Thats less that a power duo, and we all know what kind of quality processes those were constructed with. I'll still buy one though. :DI see what you are getting at but I don't think it will be as garbagey as the PowerDuo. The SP2 uses the same implements that the good SOGs use, plus the locking system from the PowerLock. So I would be surprised if there were any more play than is found on the PowerLock. We will have to see about the pliers.
The price of the PowerDuo is a reflection on the Lock-Back knife first, multi-tool second nature of the PowerDuo, IMO
-

Shopped, or something SOG considered/is considering for the future?

-
Totally shopped
-
It doesn't look like it would be able to close the handles together all the way.
The fact that the handles look slightly different and that it has two flats, as well as a CE and SE blade had me thinking prototype
-
I wonder if you will be able to swap out the file for scissors? I would even lose file and can opener for a pair of scissors.
Any news on a release date yet?
-
You can order one from SOG web site right now.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login