Replacing Crunch knife with something else?
-
Welcome bud
Look forward to seeing the mods!
-
You might want to check that the places that don't allow blades will allow an awl, as some see awls as sharp, pokey things that could cause damage to flesh. Some of the awls I have on older MTs could easily kill someone (long, thin and sharp).
-
Thanks guys! I hadn't thought of the awl being a weapon, I might go with a bottle opener or another file. My SAK file is the right thickness and has teeth like a hacksaw on it, I would like that very much.
I guess I should have stated it in the first post, but I would like to keep the knife intact to put back on if I get a different job. Also thanks for the pliers tip, I had seen the clip but not those, I might try that!
I'll keep you updated on my search for tools that fit. I'm trying to find a file from a SAK Camper
-
You might make a V cutter from it. Or replace it with scissors.
-
@Shawn Cimonetti said:
I might go with a bottle opener or another file...
there's already a bottle opener on the Crunch. ;)

Ahhhh, never notice that! I've only had the crunch for a few months and haven't needed that yet.
I really like the scissors idea too, I just need to find where to locate some. I don't have any old multitools that don't get used.
-
@Shawn Cimonetti said:
Ahhhh, never notice that! I've only had the crunch for a few months and haven't needed that yet.You may not have noticed the 1/4" bit driver either (it lives where the adjustment screw goes in). The Crunch is quite a nifty tool (my favourite MT in fact), and when you need locking pliers it really shines.
-
I have been using the hex driver actually<a href="http://s48.photobucket.com/user/Shawn_Cimonetti/media/Mobile Uploads/KIMG0027_zpsenuopxyn.jpg.html" target="_blank" rel="noopener noreferrer"><img src="http://i48.photobucket.com/albums/f218/Shawn_Cimonetti/Mobile Uploads/KIMG0027_zpsenuopxyn.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a> I found that little ball detent extensions work best in them but I have yet to put together an edc driver set. I really like the leatherman branded one though
-
<a href="http://s48.photobucket.com/user/Shawn_Cimonetti/media/KIMG0629_zpshnvxsxue.jpg.html" target="_blank" rel="noopener noreferrer"><img src="http://i48.photobucket.com/albums/f218/Shawn_Cimonetti/KIMG0629_zpshnvxsxue.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
I figured it out! Just use a sawzall blade and grind it to shape with an angle grinder.<a href="http://s48.photobucket.com/user/Shawn_Cimonetti/media/KIMG0630_zpsn996pxqr.jpg.html" target="_blank" rel="noopener noreferrer"><img src="http://i48.photobucket.com/albums/f218/Shawn_Cimonetti/KIMG0630_zpsn996pxqr.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a> I will remove all paint and use a gun bluing kit on it. I'll also replace the screws with torx. I see no problems with this, but finding the right washer thickness and shape will be hard. -
Would two sawzall blades equal Crunch blade for thickness?
-
Just about, but the problem that keeps me from putting in 2 is the teeth have set, so the bottom is thicker and 2 would not slide over each other
-
you might be able to find a way if you didn't put them next door to each other, but then you might have issues with them hitting other tools.
I wouldn't use an angle grinder myself, Dremel-type tol or bench grinder would be preferable.
Good luck!
-
It appears a blade with a .05 thickness will fit<a href="http://s48.photobucket.com/user/Shawn_Cimonetti/media/KIMG0636_zpsn4x6q4yc.jpg.html" target="_blank" rel="noopener noreferrer"><img src="http://i48.photobucket.com/albums/f218/Shawn_Cimonetti/KIMG0636_zpsn4x6q4yc.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
I don't think I want a kerf that thick, it just requires more effort -
@Cupboard said:
you might be able to find a way if you didn't put them next door to each other, but then you might have issues with them hitting other tools.I wouldn't use an angle grinder myself, Dremel-type tol or bench grinder would be preferable.
Good luck!
Thanks! I hadn't thought of that actually, I'll see what will work.
I used an angle grinder with a cutoff wheel to get the very rough shape, then will use my 6x48 belt sander, then a dremel and files for the rest.
-
I ended up using a lenox blade with a .05" thickness <a href="http://s48.photobucket.com/user/Shawn_Cimonetti/media/KIMG0636_zpsn4x6q4yc.jpg.html" target="_blank" rel="noopener noreferrer"><img src="http://i48.photobucket.com/albums/f218/Shawn_Cimonetti/KIMG0636_zpsn4x6q4yc.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
And using a heat gun and multiple vise grips and vises on a vise grip multitool I got the knurled barrel screws off. <a href="http://s48.photobucket.com/user/Shawn_Cimonetti/media/Mobile Uploads/KIMG0644_zpspswffpzs.jpg.html" target="_blank" rel="noopener noreferrer"><img src="http://i48.photobucket.com/albums/f218/Shawn_Cimonetti/Mobile Uploads/KIMG0644_zpspswffpzs.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
<a href="http://s48.photobucket.com/user/Shawn_Cimonetti/media/Mobile Uploads/KIMG0645_zps1p0mzv9h.jpg.html" target="_blank" rel="noopener noreferrer"><img src="http://i48.photobucket.com/albums/f218/Shawn_Cimonetti/Mobile Uploads/KIMG0645_zps1p0mzv9h.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a> <a href="http://s48.photobucket.com/user/Shawn_Cimonetti/media/Mobile Uploads/KIMG0647_zps4ipfgzn5.jpg.html" target="_blank" rel="noopener noreferrer"><img src="http://i48.photobucket.com/albums/f218/Shawn_Cimonetti/Mobile Uploads/KIMG0647_zps4ipfgzn5.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
I was able to slide a screwdriver through and avoid messing up spacers. <a href="http://s48.photobucket.com/user/Shawn_Cimonetti/media/Mobile Uploads/KIMG0649_zpspb2bjvn1.jpg.html" target="_blank" rel="noopener noreferrer"><img src="http://i48.photobucket.com/albums/f218/Shawn_Cimonetti/Mobile Uploads/KIMG0649_zpspb2bjvn1.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
After positioning it on the blade so that the teeth aligned and the smooth part was on solid, I clamped and traced the shape with a sharp knife. Using a blade to mark a blade on a blade. Notice a pattern haha? I planned on using the 11 amp angle grinder to hack to size then belt sand the rest. My brother had the grinder so I used my dremel with a cutoff wheel and followed the line. <a href="http://s48.photobucket.com/user/Shawn_Cimonetti/media/Mobile Uploads/KIMG0652_zpsujx8zqlu.jpg.html" target="_blank" rel="noopener noreferrer"><img src="http://i48.photobucket.com/albums/f218/Shawn_Cimonetti/Mobile Uploads/KIMG0652_zpsujx8zqlu.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>another reason why the panavise rocks for small work <a href="http://s48.photobucket.com/user/Shawn_Cimonetti/media/Mobile Uploads/KIMG0654_zpshtvjwqdz.jpg.html" target="_blank" rel="noopener noreferrer"><img src="http://i48.photobucket.com/albums/f218/Shawn_Cimonetti/Mobile Uploads/KIMG0654_zpshtvjwqdz.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
Where I'm currently at after 15 min <a href="http://s48.photobucket.com/user/Shawn_Cimonetti/media/Mobile Uploads/KIMG0655_zpskyyeo26w.jpg.html" target="_blank" rel="noopener noreferrer"><img src="http://i48.photobucket.com/albums/f218/Shawn_Cimonetti/Mobile Uploads/KIMG0655_zpskyyeo26w.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a> -
Looking good so far
-
Good work Shawn. IMO the blade could have been flipped to cut on the pull. Can't wait to see the finished product.
-
Thanks! I tried cutting a piece of angle steel on the pull and the push, and found that in order to get the teeth to grab on a low TPI saw a push worked better. On fine tooth a pull worked better. I'll see how it works out though
-
<a href="http://s48.photobucket.com/user/Shawn_Cimonetti/media/Mobile Uploads/KIMG0661_zpsbz4p1blg.jpg.html" target="_blank" rel="noopener noreferrer"><img src="http://i48.photobucket.com/albums/f218/Shawn_Cimonetti/Mobile Uploads/KIMG0661_zpsbz4p1blg.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
Here is the finished prototype. I slightly messed up the lock detent but it functions fine. I ended up not liking the push cut, and it looks too aggressive. Next version will include a pull cut and finer teeth. <a href="http://s48.photobucket.com/user/Shawn_Cimonetti/media/Mobile Uploads/KIMG0658_zpswv0ee03d.jpg.html" target="_blank" rel="noopener noreferrer"><img src="http://i48.photobucket.com/albums/f218/Shawn_Cimonetti/Mobile Uploads/KIMG0658_zpswv0ee03d.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>Where can I find the washers if I were to use a thinner blade? I don't have the skills to make them. I do have access to a laser cutter at school though...
-
@Shawn Cimonetti said:
<a href="http://s48.photobucket.com/user/Shawn_Cimonetti/media/Mobile Uploads/KIMG0661_zpsbz4p1blg.jpg.html" target="_blank" rel="noopener noreferrer"><img src="http://i48.photobucket.com/albums/f218/Shawn_Cimonetti/Mobile Uploads/KIMG0661_zpsbz4p1blg.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
Here is the finished prototype. I slightly messed up the lock detent but it functions fine. I ended up not liking the push cut, and it looks too aggressive. Next version will include a pull cut and finer teeth. <a href="http://s48.photobucket.com/user/Shawn_Cimonetti/media/Mobile Uploads/KIMG0658_zpswv0ee03d.jpg.html" target="_blank" rel="noopener noreferrer"><img src="http://i48.photobucket.com/albums/f218/Shawn_Cimonetti/Mobile Uploads/KIMG0658_zpswv0ee03d.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>Where can I find the washers if I were to use a thinner blade? I don't have the skills to make them. I do have access to a laser cutter at school though...
can u made me one? i will buy it put on rebar and ST300
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
