Mini Surge 2.0
-
@Aloha007 said:
I spent the better part of last night looking at Metros Wave mod with BE. I'm glad I stumbled upon this so I can see how this progresses.I'm still a bit confused if any grinding of the BE is needed for it to fit or if its just the Surge pivot that's needed or both
.if I remember correctly, Metro thinned out his BE because he was originally installing it in a Charge. (He also thinned out the titanium handle scale.)
I have not thinned my BE at all, partly because I'm not going to attempt this with a Charge, and also because it would be extremely difficult to evenly thin the BE using a Dremel, which is what I have to work with. ;) The Surge pivot is definitely needed though.
that being said, I still need to figure something out, because there's a lot of tension/friction on the BE and it's difficult to open. it's still perfectly usable, but I want it to open/close as smoothly as the other tools. :)
-
I spent the better part of last night looking at Metros Wave mod with BE. I'm glad I stumbled upon this so I can see how this progresses.
I'm still a bit confused if any grinding of the BE is needed for it to fit or if its just the Surge pivot that's needed or both
.if I remember correctly, Metro thinned out his BE because he was originally installing it in a Charge. (He also thinned out the titanium handle scale.)
I have not thinned my BE at all, partly because I'm not going to attempt this with a Charge, and also because it would be extremely difficult to evenly thin the BE using a Dremel, which is what I have to work with. ;) The Surge pivot is definitely needed though.
that being said, I still need to figure something out, because there's a lot of tension/friction on the BE and it's difficult to open. it's still perfectly usable, but I want it to open/close as smoothly as the other tools. :)
I'm pretty sure he didn't thin out the BE.
@Metropolicity said:
Blade ExchangerYes! You read right, a blade exchanger (BE). I've always said it couldn't be done, but somehow I did it. Taking the blade exchanger from a Surge, the small part was carefully shaped and the locking surface mated with the smaller liner lock.
This was the easy part. The BE is quite thick and needs room to move and separate to replace the blades. This was a challenge, but thanks to the thick Ti scales, material could be removed to make room for it. A whole 1mm was milled off, and a little lip was left to make sure the scale properly when buttoned up.
-
@Breezy12 said:
I was originally going to wait until it was completely finished, but I couldn't resist sharing this one with you guys. :DEver since Metro showed us the Master & Commander, I've been wanting to try fitting a Blade Exchanger into a Wave/Charge. I knew it would be a challenge using only a Dremel and some hand files, but I figured it was worth a shot. ;)
to start with, a public service announcement: be wary of buying tools on ebay listed as having "some light rust spots, but otherwise in great condition."


a couple hours and plenty of elbow grease later, I had the donor Surge parts all cleaned up, especially the all-important Blade Exchanger. :)
a few months later, I finally got around to starting on the mod.
as with any Dremel/grinding work, slow & steady is the key... and I'm happy with this one. :) I used a reinforced cutting wheel to carefully cut out the section needed for the BE, then used a carbide bit to run along the edges and smooth them out a little bit. after that was a hand file (the diamond file on another LM Wave, actually), and finally some fine grit sandpaper to finish it off. the result is a nice smooth line that has zero chance of cutting the user's hand. ;)

I've been using a lot of Wingman scissors lately, so I decided to branch out and give the infamous 91mm Vic scissors a try on this one.


however, I got a little Dremel-happy and ground off just a hair too much, so the lockup isn't quite as nice as I'd like it to be. :-\ I haven't decided if I'm going to switch to Wingman scissors or sacrifice another SAK.

anyway, here's what it looks like at this point. I found some 3.25" jigsaw blades at Harbor Freight that fit into the Wave frame perfectly, so that adds some flexibility to the tool's loadout.


and yes, I realize that the pivots don't match. I still need to trim the other Surge pivot, but I wanted to get the tool put together for the pics. I'm going to disassemble the whole thing and send the handles in for Cerakoting
to cover up the spots where the Dremel slippedjust for fun. :D I'm planning on a two-tone look, with black handles and SS tools.I'm also going to use this one as sort of a test platform. some ideas I want to try:
- grinding the large flat driver into a chisel and/or light-duty pry bar
- replacing the can opener with a Vic combo tool
- replacing the large flat driver with the Wingman package opener (need to find the right spacer to go along with the package opener, since it's thinner than the flat driver)
I'll be sure to post an update with more pics once I get the handles cerakoted and make some more progress. in the meantime, feel free to add to my list of ideas to try. ;)
HOLY SMOKE !!!

-
Way to go Breezy!!!!!!!
-
Maybe try to intergrate a mini flashlight?

-
BUMP
Breezy how are you coming along with the BE on the Wave? I scored a Surge that I'd love to take the BE off and try with my polished Wave.
-
@dan.mandiel said:
Maybe try to intergrate a mini flashlight?

How about putting a fauxton on a split ring ?
-
Breezy how are you coming along with the BE on the Wave? I scored a Surge that I'd love to take the BE off and try with my polished Wave.
sadly, I am not coming along with it at all.

work/real life have been busier than usual lately, but I am taking a couple days off next week, so I should be able to find some time to (hopefully) catch up on my mods. ;) I'll keep you posted!
FYI - I also recently scored a new model Surge at a good price, so I plan on taking the updated BE from that one and comparing the two to see how each of them fits in the Wave.

-
BUMP
Breezy how are you coming along with the BE on the Wave? I scored a Surge that I'd love to take the BE off and try with my polished Wave.
sadly, I am not coming along with it at all.

work/real life have been busier than usual lately, but I am taking a couple days off next week, so I should be able to find some time to (hopefully) catch up on my mods. ;) I'll keep you posted!
FYI - I also recently scored a new model Surge at a good price, so I plan on taking the updated BE from that one and comparing the two to see how each of them fits in the Wave.

I was wondering where you had gone off to.
-
BUMP
Breezy how are you coming along with the BE on the Wave? I scored a Surge that I'd love to take the BE off and try with my polished Wave.
sadly, I am not coming along with it at all.

work/real life have been busier than usual lately, but I am taking a couple days off next week, so I should be able to find some time to (hopefully) catch up on my mods. ;) I'll keep you posted!
FYI - I also recently scored a new model Surge at a good price, so I plan on taking the updated BE from that one and comparing the two to see how each of them fits in the Wave.

The plot thickens.
I look forward to your findings. Hope you get some modding time in and not just for us to enjoy but for yourself.
-
Breezy, whats up buddy? I know this thread is old but just wanted to stop by to say, I finally did it!!!
Thanks to this thread I installed a BE on my Wave. I've not encountered the opening issues thankfully and hopefully you resolved yours. Miss ya bud.

-
Thanks for necro Aloha
I shall give this a good read later tonight 
-
Breezy also links to Metros Charge blade exchanger mod. His is high quality as are all his mods.
-
@Aloha007 said:
Breezy, whats up buddy? I know this thread is old but just wanted to stop by to say, I finally did it!!!Thanks to this thread I installed a BE on my Wave. I've not encountered the opening issues thankfully and hopefully you resolved yours. Miss ya bud.
thanks Aloha!! looks like you did a fantastic job putting that BE into your Wave.

the opening issues I was dealing with sort of worked themselves out... just needed to break it in a bit, I guess.

I also tried replacing the original BE with a BE from the newer model Surge... that one did not fit as well, and stuck up above the handle too much for my taste. I can try to get some pictures later. I suppose I could try reworking the handle a bit, but at the time, it was much easier to just put the original BE back in place. :D
-
Hey bud. Thanks to you I was able to make it finally happen. This thread helped me so much and for that I am thankful to you. Hope all is well and its great to hear from you

-
it's good to be back!
I posted in the NLC forum too with a little more info if you're curious/interested.I'm glad you found this thread useful... I am always happy to help whenever I can.

I need to go poke around the Mod Squad some more and see what other mods people have been up to... I seem to be catching another case of mod fever. :D
-
@Breezy12 said:
it's good to be back!
I posted in the NLC forum too with a little more info if you're curious/interested.I'm glad you found this thread useful... I am always happy to help whenever I can.

I need to go poke around the Mod Squad some more and see what other mods people have been up to... I seem to be catching another case of mod fever. :D

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login