firearms
-
Doing that right now.

-
Just finished cleaning the handgun...this time taking apart the firing pin assembly. As read from a few online forums, there were some metal fragments in the firing pin channel. I gave it a good cleaning. I hope this will fix the issue I had this weekend.
-
Hope that helped! 
-
@Chako said:
I got at the range an hour early to get some much needed practice time. I couldn't figure out what I was doing wrong yesterday, as I was shooting a lot better when I go alone. I then looked back at what I changed and figured out that I was wearing a cheap pair of plastic safety glasses...the type that are designed to fit over prescription glassware. These caused me nothing but problems with distortions, glares, and haze.Well I took them off and I was shooting a lot better. So well that I wasn't asked to re-do any stages today. I passed the course. Now I have to shoot a sanctioned match, send in my info card, and I will be sent a black badge.

Hmmm...I have had 8 soft strikes on 8 separate 9 mm rounds. I was shooting Barnaul, which is made in Russia. Not sure if the ammo is the issue, or my M&P. Going to try something different and see if it still persist. If not, then it is the ammunition. I think I will be staying away from this stuff anyways as I found out recently you can't re-use the casings...and it is only 2 dollars cheaper than the Remington's that use brass casings.
Seems like you figured it out already, but I would stay away from steel cased stuff as well as Russian ammunition. I normally only buy Federal (brass) ammunition. It has been the most consistent and normally cheaper than the more expensive Winchester and Remington ammunition. I tend to stay away from Remington ammunition all together after multiple occasions of questionable and obvious quality issues.
-
Wipe the breach face and the interiors of magazines dry, particularly if you are going to store them loaded. Penetrating fumes from solvents can ruin both primers and powder. On my ready-use pistol I like to load Winchester. They use a sealant on the primer.
On your reload cases make sure they're Boxer cases with a single centered flash hole; not Berdan cases with two off-center flash holes. Most American is Boxer primed; a lot of European in Berdan primed
-
I had problems with light primer strikes with a S&W 586 357 Magnum. I finally traded it for something else. I found out later that some S&W revolvers have problems with some primers, including CCI primers. I still use CCI primers and haven't had issues with other firearms so far.
-
Well this is what I was doing. At the local Canadian Tire, they stocked 2 types of 9 mm ammunition. Russian Barnaul, and Czech Sellier & Bellot. The Sellier ammo was a dollar more. I bought a few boxes of each every now and then. Then the Czech ammo disappeared and they only had the Russian stuff. Hence I bought a lot of the Russian stuff in fear that this supply of 9 mm ammo would dry up. They brought in a more expensive Remington 9 mm, and I started buying this instead. By this time, I had around 700 9 mm rounds of the Russian stuff.
So yes, I won't be buying anymore of the Barnaul ammo. I still have 500 rounds of this after the course.
-
We burned some powder last weekend. Here are some of the toys that showed up. :)
-
Looks like fun!!!

-
@Chako said:
Well this is what I was doing. At the local Canadian Tire, they stocked 2 types of 9 mm ammunition. Russian Barnaul, and Czech Sellier & Bellot. The Sellier ammo was a dollar more. I bought a few boxes of each every now and then. Then the Czech ammo disappeared and they only had the Russian stuff. Hence I bought a lot of the Russian stuff in fear that this supply of 9 mm ammo would dry up. They brought in a more expensive Remington 9 mm, and I started buying this instead. By this time, I had around 700 9 mm rounds of the Russian stuff.So yes, I won't be buying anymore of the Barnaul ammo. I still have 500 rounds of this after the course.
What is expensive up in the GWN?
I pay about 24 USDollars for 100 rounds on Winchester 115 grain 9mm here.
-
@kosmo said:
I had problems with light primer strikes with a S&W 586 357 Magnum. I finally traded it for something else. I found out later that some S&W revolvers have problems with some primers, including CCI primers. I still use CCI primers and haven't had issues with other firearms so far.I had not heard about S&W having this problem. I not as tuned in to the gun world as I once was. My Smiths are older guns and dont suffer from that problem.
-
It was. I dont shoot much any more but joined in the other day when the guys showed up. That AR was chambered for the 300 Blackout and was fun to play with as I hadnt shot one before. I really enjoyed shooting Doc Tonys Winchester 92 in 38-40. You cant see it in the picture but it has an octagon barrel. Its a sweet little rife. :)
-
For you right handed pistoleros who are not getting hits where you want them. If this will show up maybe it will help you get better hits. :)
-
Remington 9 mm 50 rounds = 20 dollars
Sellier & Bellot 9 mm 50 rounds = 18 dollars
Barnaul 9 mm 50 rounds = 17 dollars20 rounds of 30-06 can run from 23 dollars up to 50 dollars
.22 LR box of Remington Golden Bullets 525 round count = 40 something dollars
This is all at Canadian Tire. The local gun shop prices are higher overall.
-
I had problems with light primer strikes with a S&W 586 357 Magnum. I finally traded it for something else. I found out later that some S&W revolvers have problems with some primers, including CCI primers. I still use CCI primers and haven't had issues with other firearms so far.
I had not heard about S&W having this problem. I not as tuned in to the gun world as I once was. My Smiths are older guns and dont suffer from that problem.
From people I've talked to since then, it is a known problem. It may be S&W that have been modified or trigger jobs. This guy made a video on the problem.
-
I had problems with light primer strikes with a S&W 586 357 Magnum. I finally traded it for something else. I found out later that some S&W revolvers have problems with some primers, including CCI primers. I still use CCI primers and haven't had issues with other firearms so far.
I had not heard about S&W having this problem. I not as tuned in to the gun world as I once was. My Smiths are older guns and dont suffer from that problem.
From people I've talked to since then, it is a known problem. It may be S&W that have been modified or trigger jobs. This guy made a video on the problem.
If these came from the factory like that its not good. If a gunsmith did it it can usually be corrected fairly easily. I've had a lot of guns modified to my personal needs but I've always went to top gunsmiths while they are expensive you seldom have problem with their work like you would with the shade tree gunsmiths out there. I'm glad you posted that video. :tu: It saved me a very long winded reply. :D
-
I had problems with light primer strikes with a S&W 586 357 Magnum. I finally traded it for something else. I found out later that some S&W revolvers have problems with some primers, including CCI primers. I still use CCI primers and haven't had issues with other firearms so far.
I had not heard about S&W having this problem. I not as tuned in to the gun world as I once was. My Smiths are older guns and dont suffer from that problem.
From people I've talked to since then, it is a known problem. It may be S&W that have been modified or trigger jobs. This guy made a video on the problem.
If these came from the factory like that its not good. If a gunsmith did it it can usually be corrected fairly easily. I've had a lot of guns modified to my personal needs but I've always went to top gunsmiths while they are expensive you seldom have problem with their work like you would with the shade tree gunsmiths out there. I'm glad you posted that video. :tu: It saved me a very long winded reply. :D
True, but it's not typical to take apart the inner workings of a gun to find out their condition when buy them second had, or new for that matter. Although I am very mechanically inclined, I don't have the expertise of a gunsmith. I didn't encounter this problem until I started shooting my hand loads. They shoot fine from my other 357's.
If I had known about this issue, I might have tried to have it adjusted. I might have even changed primers, but I didn't find out about it until I had traded it way. I had more issues with S&W 586 that I didn't like, the light primer strikes was one issue. My 586 was a long barrel ~8". It was very difficult to shoot the 8" S&W 586 accurately in double action. Even though it had a nice smooth trigger pull. Pulling a trigger in double action while steadying a long 8" barrel is very difficult. In single action my hands were large enough that I had to reposition my hand (twist my wrist) or the trigger was well into the second pad of my trigger finger (beyond the first joint). I tried putting a larger Hogue grip on it, but it still suffered from this problem. I found it very annoying to have to reposition my hand depending on whether I was shooting it double action or single action.
I've since switched to a TC Contender with Pachmayr grip. It is also an 8" barrel. But because it doesn't have a cylinder, it compares favorably with the length of a 6" revolver. It is single action only and the grip size to trigger finger is much better than the S&W 586/686.

I also have a Ruger LCR in 357 Magnum. It has a prefect grip size for me and it is double action only, so I don't have the issue that I had with the S&W.

-
Sweet LCR. Ruger just came out with a new one this year. The LCRx.
-
@captain spaulding said:
Sweet LCR. Ruger just came out with a new one this year. The LCRx.The LCRx with the exposed hammer has been tempting me. I REALLY like the 3" LCRx! But I decided I'd wait and see if they come out with a 357 Magnum. I'm all set up to load 357 Magnum and I can load it hot or mild. I really don't want to start loading 38 Special.
-
@captain spaulding said:
Sweet LCR. Ruger just came out with a new one this year. The LCRx.
The LCRx with the exposed hammer has been tempting me. I REALLY like the 3" LCRx! But I decided I'd wait and see if they come out with a 357 Magnum. I'm all set up to load 357 Magnum and I can load it hot or mild. I really don't want to start loading 38 Special.
I would wait for the .357 as well.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login