Sharpening, discuss.
-
@Steinar said:
It really boils down how much steel you are willing to throw away to get an edge and the quality you need for that edge. For a knife that needs a new edge, I simply use a sharpie to mark the edge to easier see where I actually remove material. For the actual sharpening, I use a Spyderco Sharpmaker. That said, I sometimes use a pull-through (ceramic for touch-up, carbide for reshaping); you just need to think about what you're doing. Seems the cap has his work cut out for him here. :DI have seen knives ruined with pull-through sharpeners, an activity for which they are perfectly suited, but it's not like the edge spontaneously disintegrates just because the ceramic rods which do the sharpening is placed closer together than on the Sharpmaker... ;)
I'm clumsy, lazy and impatient, so I take all the help I can get when I sharpen my knives. The diamond rods to reshape new blades with ridiculously obtuse edge angle was one of my better buys. Trying to reshape an edge with one of the ceramic hones on a Sharpmaker is an exercise in futility. (Getting the super-fine rods to polish edges wasn't too dumb either.)
A lot of good stuff here WolfenStein and this reminds me I need one more UF rid for my SM.
Accidentally bought a single of Amazon. Who needs just one rod for a SM?
-
I like to strop(backwards from sharpening) on leather in between uses as much as i can before sharpening. It saves steel from wearing out. I made a strop by gluing an old belt on a 2x2. I load it with metal polish for extra sharpness
For sharpening, I sharpen freehand. As if I were gently scraping a postage stamp off the stone.
For really dull knives I use a diamond rod. Then I use a ceramic rod freehand and finish on a black arkansas stone.
Some knives have a convex edge or I might have a knife i want a microbevel for rough use and woodcarving. Not for use on vegtables or meat as it is not ideal for slicing. I put a microbevel convex on a Vic OHT Non serrated and that knife has been sharp for a year.
For this I have a computer mousemat taped on a box where I tack wet and dri in varing degrees. For this go backwards like stropping. Then finish stropping on leather
For chizel grind serrated knives I use the edge of the stone or use a rod. I sharpen just as i would if it were no serrated except seven times on the chizel side and two on the flat side to remove the burr. Strop afterward with the same 7x2 ratio
I put a microbevel on this mora knife and used the heck out of it carving wood. I stropped and it still feels sharp


-
I am a sharpening noob.

A $20 3in1 sharpener and a 6" leather strap keep my knives sharp enough for normal use, but never as sharp as manufacturer's edge.I been wondering myself if I should upgrade to a more advance system.
-
@Steinar said:
It really boils down how much steel you are willing to throw away to get an edge and the quality you need for that edge. For a knife that needs a new edge, I simply use a sharpie to mark the edge to easier see where I actually remove material. For the actual sharpening, I use a Spyderco Sharpmaker. That said, I sometimes use a pull-through (ceramic for touch-up, carbide for reshaping); you just need to think about what you're doing. Seems the cap has his work cut out for him here. :DI have seen knives ruined with pull-through sharpeners, an activity for which they are perfectly suited, but it's not like the edge spontaneously disintegrates just because the ceramic rods which do the sharpening is placed closer together than on the Sharpmaker... ;)
I'm clumsy, lazy and impatient, so I take all the help I can get when I sharpen my knives. The diamond rods to reshape new blades with ridiculously obtuse edge angle was one of my better buys. Trying to reshape an edge with one of the ceramic hones on a Sharpmaker is an exercise in futility. (Getting the super-fine rods to polish edges wasn't too dumb either.)
This
other tips are do your sharpening where there is good light 
-
Me too. :D
I've got a Lanksy Standard 3-stone set and while it's good for deep blades it's a PITA for SAKs. Mostly I just use the stones freehand, and try to gauge the angle by eye. I've also got a Victorinox pocket sharpener which is only good for touch ups and serrations. I reckon a Sharpmaker would suit me better, but I can't really see the difference between that and spending 1/3 of the cost of the Spyderco on a Lanksy 4-rod turnbox.
-
@HarleyXJGuy said:
A lot of good stuff here WolfenStein and this reminds me I need one more UF rid for my SM.Accidentally bought a single of Amazon. Who needs just one rod for a SM?
Oh! I know this one! A guy who only own chisel ground blades! Did I win anything? ;)
-
Even if you only have chisel ground blades, don't you need to take the burr off the back?
I've got a Lanksy which taught me how to sharpen but is a faff and I don't use it much. Most sharpening is done freehand on a cheap and crude 4 sided diamond block. It's quick and easy. At work touchups are done with a stone that lives there that I found in a cupboard, and if I'm really desperate we've got a small belt sander cum furry wheel thing for doing cow hoof knives.
-
@Sparky415 said:
This
other tips are do your sharpening where there is good light 
Absolutely.
I find it helpful to see where light reflects from the edge. Light should only be reflected from the flat edges where the hones remove stock, not from the actual edge, that would be chipping and edge rolling that has to be fixed. (Not sure if this was understandable. I rotate the knife under god light, for a knife with a Scandi grind and no secondary bevel, then light would first reflect from the side of the blade, then the side of the edge, then the other side of the edge, then the other side of the blade. If I see small points reflecting light between the sides of the edge, then I know the edge is damaged there. Sorry about the very clumsy language, wasn't sure how to get this across.) -
I am a sharpening noob.

Me too. :D
I've got a Lanksy Standard 3-stone set and while it's good for deep blades it's a PITA for SAKs. Mostly I just use the stones freehand, and try to gauge the angle by eye. I've also got a Victorinox pocket sharpener which is only good for touch ups and serrations. I reckon a Sharpmaker would suit me better, but I can't really see the difference between that and spending 1/3 of the cost of the Spyderco on a Lanksy 4-rod turnbox.
If you're willing to customize your box and if you don't encounter many serrations there is no reason
-
This
other tips are do your sharpening where there is good light 
Absolutely.
I find it helpful to see where light reflects from the edge. Light should only be reflected from the flat edges where the hones remove stock, not from the actual edge, that would be chipping and edge rolling that has to be fixed. (Not sure if this was understandable. I rotate the knife under god light, for a knife with a Scandi grind and no secondary bevel, then light would first reflect from the side of the blade, then the side of the edge, then the other side of the edge, then the other side of the blade. If I see small points reflecting light between the sides of the edge, then I know the edge is damaged there. Sorry about the very clumsy language, wasn't sure how to get this across.)I understand that perfectly, if you are outside get the sun behind you ;)
I also find a magnifying glass helps me a lot (but that’s just me :-[ ) -
I have a variety or whet stones and diamond hones, always done freehand but I'm thinking of trying a sharp maker soon, maybe.
-
I am a sharpening noob.

Me too. :D
I've got a Lanksy Standard 3-stone set and while it's good for deep blades it's a PITA for SAKs. Mostly I just use the stones freehand, and try to gauge the angle by eye. I've also got a Victorinox pocket sharpener which is only good for touch ups and serrations. I reckon a Sharpmaker would suit me better, but I can't really see the difference between that and spending 1/3 of the cost of the Spyderco on a Lanksy 4-rod turnbox.
I have an Swisstool but the blade is the same as a SAK.
I use the slanky sharpening system, it works the same as the sharpmaker.
But it is a a third of the price.Gets it razor sharp, and works just as good as the sharpmaker of a friend of mine.
I never had succes with a stone, probably because i have a crappy stone, but the lansky system/sharpmaker has a set angle. It is much easier and gets it hair popping sharp.
-
@Sparky415 said:
I understand that perfectly, if you are outside get the sun behind you ;)That's good advice.

I also find a magnifying glass helps me a lot (but that’s just me :-[ )
I bought a small loupe/jeweler's magnifier, but haven't figured out how to use it effectively when sharpening. So, I have ended up prefering a magnifying glass. :)
-
Another Spyderco Sharpmaker fan. Works on everything I need to sharpen.
-
I am a sharpening noob.

Me too. :D
I've got a Lanksy Standard 3-stone set and while it's good for deep blades it's a PITA for SAKs. Mostly I just use the stones freehand, and try to gauge the angle by eye. I've also got a Victorinox pocket sharpener which is only good for touch ups and serrations. I reckon a Sharpmaker would suit me better, but I can't really see the difference between that and spending 1/3 of the cost of the Spyderco on a Lanksy 4-rod turnbox.
I have an Swisstool but the blade is the same as a SAK.
I use the slanky sharpening system, it works the same as the sharpmaker.
But it is a a third of the price.Gets it razor sharp, and works just as good as the sharpmaker of a friend of mine.
I never had succes with a stone, probably because i have a crappy stone, but the lansky system/sharpmaker has a set angle. It is much easier and gets it hair popping sharp.
Is this what you use ?
http://lansky.com/index.php/products/4-rod-turn-box/ -
I am a sharpening noob.

Me too. :D
I've got a Lanksy Standard 3-stone set and while it's good for deep blades it's a PITA for SAKs. Mostly I just use the stones freehand, and try to gauge the angle by eye. I've also got a Victorinox pocket sharpener which is only good for touch ups and serrations. I reckon a Sharpmaker would suit me better, but I can't really see the difference between that and spending 1/3 of the cost of the Spyderco on a Lanksy 4-rod turnbox.
I have an Swisstool but the blade is the same as a SAK.
I use the slanky sharpening system, it works the same as the sharpmaker.
But it is a a third of the price.Gets it razor sharp, and works just as good as the sharpmaker of a friend of mine.
I never had succes with a stone, probably because i have a crappy stone, but the lansky system/sharpmaker has a set angle. It is much easier and gets it hair popping sharp.
Is this what you use ?
http://lansky.com/index.php/products/4-rod-turn-box/Yup, that's the one.
For longer knives the rods may be a bit short but there is also a version with longer rods. For SAKs, MTs and bushcraft knives it works fine.Machetes may be a different story ???
-
I have a spiderco system and a lansky. However, I find myself to be better with basic whetstones then stropping with green paste, linen and leather. I originally learned on stones, the strop is more just the past year or so as I use a straight razor as well. Keeps things SHARP...
-
I am another disciple of the Sharpmaker. I have had several different stones etc. and have found the Sharpmaker to be easy to use, fairly quick, and obtain consistent shaving sharp edges with it!
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login