Salt water Multitool
-
PVD coating is awesome and can stand up to a lot of abuse. It isn't very expensive to have it done on a lot of parts vs. one or a few parts. Someone could make a good living taking various multitools apart and sending them off to have them PVD coated and then reselling them. They do lots of other colors including a titanium aluminum nitride coating that looks like black oxide but doesn't rub off, ever. They say it has the same hardness as diamond. There are even low temperature coatings that don't affect the heat treat of blades and tools and still provide most of the protection.
-
Thanks to all.
I had a look at some Diving shops but found nothing.
H1 steel. as used in the spyrco salt series should have been an option but maybe it is not suitable for anything other than knives (too brittle, too elastic, too weak ??? I do not really know.)
A coating is good, but it has to be scratch resistant and really on a knife that you need to sharpen could not work 100%
The beryllium alloy sound interesting, but its rockwell rating is quite low (copper is soft, berillium is brittle) for a knife.
Maybe a combination of all would make one multitool that works in sea water well?
The leatherman and the SOG shown look really sweet and expensive...
-
I had a look at some Diving shops but found nothing.
H1 steel. as used in the spyrco salt series should have been an option but maybe it is not suitable for anything other than knives (too brittle, too elastic, too weak ??? I do not really know.)
A coating is good, but it has to be scratch resistant and really on a knife that you need to sharpen could not work 100%
The beryllium alloy sound interesting, but its rockwell rating is quite low (copper is soft, berillium is brittle) for a knife.
Maybe a combination of all would make one multitool that works in sea water well?
The leatherman and the SOG shown look really sweet and expensive...
H1 steel would actually make a very good plier head - very hard, but extremely tough - it doesn't get brittle, either. Spyderco had a demonstration when their H1 steel knives came out a few years ago where they bent the blade on a Pacific Salt 90 degrees in a vice and it didn't snap.
The problems would be:
- H1 is expensive
- H1 steel cannot be machined in certain ways because it's a work hardening steel. For example, Spyderco does not flat grind any H1 blades.
-
I'm going back "A couple" years here.
But after my Wave and my OHT rusting in my pocket I'm on the prowl.
I'm living in the worst conditions for a MT.
Dipped in Salt water, falling in beach sand, covered in fish slime, cutting bait, bending hooks, and even sawing drift wood.
Did anyone ever find a solution? Maybe dip my wave in some T9 BioShield efore every trip? But I don't want the oils dispensing into my pants if I'm wading
-
A buddy of mine charters out of San Diego. He's carried a SwissTool for what has to be close to 20 years..... He uses it hard and it's finish doesn't seem to bothered at all by the environment.
Sent from my iPad using Tapatalk
-
SOG BlackTip? at least they're cheap at the moment, handful left at West Marine for < $30. Just take any stainless tool and rinse it with fresh water and spray down with CLP afterwards.
Lots of stainless marlinspike clasp knives issued by various navies for the last 100 years.
http://www.ebay.com/itm/IXL-Three-Piece-British-Army-Clasp-Knife-4-closed-Polished-stainless-sheepsfoot-/351278736825?pt=LH_DefaultDomain_0&hash=item51c9d825b9
http://www.ebay.com/itm/GERMAN-SAILING-POCKET-BOAT-YACHT-KNIFE-WITH-MARLINSPIKE-MULTI-TOOL-GREAT-PRICE-/191578736157?pt=LH_DefaultDomain_0&hash=item2c9afb861d -
I am not sure what is more rust proof, BO Swisstool or polished Swisstool.
But i think the polished ST is more rust proof.
Other than that i don't think you can get a tool that is more rust proof. -
@NKlamerus said:
I'm going back "A couple" years here.But after my Wave and my OHT rusting in my pocket I'm on the prowl.
I'm living in the worst conditions for a MT.
Dipped in Salt water, falling in beach sand, covered in fish slime, cutting bait, bending hooks, and even sawing drift wood.
Did anyone ever find a solution? Maybe dip my wave in some T9 BioShield efore every trip? But I don't want the oils dispensing into my pants if I'm wading
Sounds like you need a Marine Tuff Cloth. Seriously these things are awesome. They will make your tool smell like gasoline for a day or two but make a invisible shield against rust. Best of all they do not leave a oily surface on your tools. Once it dries its like its not even there except for keeping the rust away. Check them out on youtube. For your needs I would get the Marine version.
-
@captain spaulding said:
I'm going back "A couple" years here.
But after my Wave and my OHT rusting in my pocket I'm on the prowl.
I'm living in the worst conditions for a MT.
Dipped in Salt water, falling in beach sand, covered in fish slime, cutting bait, bending hooks, and even sawing drift wood.
Did anyone ever find a solution? Maybe dip my wave in some T9 BioShield efore every trip? But I don't want the oils dispensing into my pants if I'm wading
Sounds like you need a Marine Tuff Cloth. Seriously these things are awesome. They will make your tool smell like gasoline for a day or two but make a invisible shield against rust. Best of all they do not leave a oily surface on your tools. Once it dries its like its not even there except for keeping the rust away. Check them out on youtube. For your needs I would get the Marine version.
Added to the cart!
I might order some T9 for the joints too.
-
@captain spaulding said:
I'm going back "A couple" years here.
But after my Wave and my OHT rusting in my pocket I'm on the prowl.
I'm living in the worst conditions for a MT.
Dipped in Salt water, falling in beach sand, covered in fish slime, cutting bait, bending hooks, and even sawing drift wood.
Did anyone ever find a solution? Maybe dip my wave in some T9 BioShield efore every trip? But I don't want the oils dispensing into my pants if I'm wading
Sounds like you need a Marine Tuff Cloth. Seriously these things are awesome. They will make your tool smell like gasoline for a day or two but make a invisible shield against rust. Best of all they do not leave a oily surface on your tools. Once it dries its like its not even there except for keeping the rust away. Check them out on youtube. For your needs I would get the Marine version.
Added to the cart!
I might order some T9 for the joints too.

It should keep the rust at bay MUCH better than before. I am interested to see your experience with them since you are in a highly corrosive area. Keep us updated.

-
@captain spaulding said:
@captain spaulding said:
I'm going back "A couple" years here.
But after my Wave and my OHT rusting in my pocket I'm on the prowl.
I'm living in the worst conditions for a MT.
Dipped in Salt water, falling in beach sand, covered in fish slime, cutting bait, bending hooks, and even sawing drift wood.
Did anyone ever find a solution? Maybe dip my wave in some T9 BioShield efore every trip? But I don't want the oils dispensing into my pants if I'm wading
Sounds like you need a Marine Tuff Cloth. Seriously these things are awesome. They will make your tool smell like gasoline for a day or two but make a invisible shield against rust. Best of all they do not leave a oily surface on your tools. Once it dries its like its not even there except for keeping the rust away. Check them out on youtube. For your needs I would get the Marine version.
Added to the cart!
I might order some T9 for the joints too.

It should keep the rust at bay MUCH better than before. I am interested to see your experience with them since you are in a highly corrosive area. Keep us updated.

Sure will!
-
@captain spaulding said:
I have been using the stronger, marine version for a few years. I use it on any non SS blades I have stored/not used regularly (e.g. Svord) as I do not have to worry about them rusting when left for a few months/years.
The plastic container keeps it moist and it lasts for a long time.
The downside is the smell. Usually when I coat a few blades I have to leave them outside for a day or two, before storing, for the smell to go. (similar to brasso)
It seems to work well so farI didn't find the smell that bad and once they dried I couldn't smell anything.
Maybe my sniffer isn't what it used to be. 
@captain spaulding said:
I'm going back "A couple" years here.
But after my Wave and my OHT rusting in my pocket I'm on the prowl.
I'm living in the worst conditions for a MT.
Dipped in Salt water, falling in beach sand, covered in fish slime, cutting bait, bending hooks, and even sawing drift wood.
Did anyone ever find a solution? Maybe dip my wave in some T9 BioShield efore every trip? But I don't want the oils dispensing into my pants if I'm wading
Sounds like you need a Marine Tuff Cloth. Seriously these things are awesome. They will make your tool smell like gasoline for a day or two but make a invisible shield against rust. Best of all they do not leave a oily surface on your tools. Once it dries its like its not even there except for keeping the rust away. Check them out on youtube. For your needs I would get the Marine version.
:D
-
I knew you would quote me on that. :D
After I initially wrote that I used the cloth again and really got the full effect. It is quite pungent.
-

:D
I saw your post and went... "wait a minute..." :D
I can imagine people getting high on these fumes.. :D
-
So this stuff is a liquid in a pouch, that a rag is soaked in?
What if I put the tool in the bag and shook it up?
-
There are various forms. Mine is a soaked rug in a plastic container. You can also buy the liquid itself or the rug in a pouch.
-
The one I linked to is the rag soaked in the stuff. I would personally stick with that unless you have a reason to want the liquid.
-
Now I just imagine Cap sticking his nose in the bag...
"Sniiiiiiiiffffffffff!!!!! Yeah... man... the fumes aren't TOO bad."

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
