And so it begins.... (My adventures into Alox!)
-
Mmm purple...

You need a twelve step program Mary.
doubt it. I'm hopeless.
-
I havent built a 58 in awhile, but here is a minichamp in blue anodized Ti, with tweezers and awl added from a 91.





-
I have another question regarding the pen: if you cut a longer slot, will it fit instead of the toothpic? P.s.: I'm trying to contact you through pm and email for a mod.
-
Im working on a copper accented Ti mod next. It was actually easier to fill with copper as it flowed easier I could be less exact with the hand cutting of the + shape and it squished itself in there nicely.


-
I had a very old mod of mine come back for a change and it was so nice to see something come in that had been used.
This was number 83 ( Im currently working on 425 ) so this was quite an older one.
Here is what it looked like as delivered. This was a bladeless mod.


And here is what it looks like today. The owner decided a small blade to be of more use than can opener, and also wanted the keyring removed.



It was nice to see some worn alox, I dont get to see it often. :D Ive had some cerakote mods come back but they dont hold up near as well as anodize so I'll probably not bother with cerakote again.

-
And project Ti with copper is done now too.
I didn't have copper rod the right size to rivet the tweezer head together.. then after some digging in the garage I found some household wire. Turns out the diameter of the ground wire is 1/16th inch, the exact rivet size I use and it's pure copper. Worked great. :D
This is a none backscale cutout build so it has the awl on back for blade layer.








-
I think that's my favorite thing you've made yet syph

-
That's bloody stunning mate :)
Sent from my K013 using Tapatalk
-
Yup, the more of these I see, the more I want my Rogueneer to get the Ti upgrade :)
Sent from my XT901 using Tapatalk
-
That's superb!
Aren't you worried about a galvanitic reaction between all the dissimilar metals seizing it all together though ;) ;) -
Be A U ti FUL!

-
@neillcurrie said:
That's superb!
Aren't you worried about a galvanitic reaction between all the dissimilar metals seizing it all together though ;) ;)If the Al and Cu were touching yes, but since the Al is anodized its non conductive. The Ti is pretty well inert so maybe the copper would oxidize faster? Not sure really but we'll see what happens. :D
-
This is a none backscale cutout build so it has the awl on back for blade layer.

Do you have a hidden 4th pin for holding the back springs that have back side tools? I would like to try putting a multitool hook in an 84mm alox.
Yes I drill into the scale of each side about 2 mm with carbide PCB circuit board drill bit of 2.2mm and that works perfect.
84 alox scales are too thin to sink a hole that far but you might be able to get it deep enough to work if you use a 2.2mm endmill after first spotting the hole with a standard pointed drill bit.
-
Now for the next step: embedding a 1 carat diamond into the Tweezer copper end

-
@neillcurrie said:
Now for the next step: embedding a 1 carat diamond into the Tweezer copper end

Good guess! But not diamond...
I'm practicing my gem setting first though. -
A couple of questions for you Syph, and maybe this was covered elsewhere, but what is required to put a small blade in a 93mm in place of the awl, is there a factory spacer that works?
And, is the file from a 91mm a direct drop in on a 93mm saw spring?
Thanks in advance, I'm trying to figure out what to send you for a custom, if you're willing and still taking 93mm requests.
:)
-
@twiliter said:
A couple of questions for you Syph, and maybe this was covered elsewhere, but what is required to put a small blade in a 93mm in place of the awl, is there a factory spacer that works?And, is the file from a 91mm a direct drop in on a 93mm saw spring?
Thanks in advance, I'm trying to figure out what to send you for a custom, if you're willing and still taking 93mm requests.
:)
A small blade is a wee bit thinner than the awl, so I make little washers to fill out the remainer of the space, but other than that they fit no problem.
91mm file works on the 93mm saw spring with no changes needed (other than making the pivot hole bigger).
:D
-
A couple of questions for you Syph, and maybe this was covered elsewhere, but what is required to put a small blade in a 93mm in place of the awl, is there a factory spacer that works?
And, is the file from a 91mm a direct drop in on a 93mm saw spring?
Thanks in advance, I'm trying to figure out what to send you for a custom, if you're willing and still taking 93mm requests.
i
:)A small blade is a wee bit thinner than the awl, so I make little washers to fill out the remainer of the space, but other than that they fit no problem.
91mm file works on the 93mm saw spring with no changes needed (other than making the pivot hole bigger).
:D
Thanks, will continue on PM...

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login