What did you use your Sak on today?
-
I also collect older diecast toys/models and purchased a Dinky Supertoys 661 Scammell Explorer Recovery Tractor off of Ebay, which arrived yesterday. .
First of all, I had to remove the foot diameter shroud of Saran wrap the seller used instead of a box. The scissors and blade on my Craftsman made (relatively) quick work of that.
Then I had to cut the bubble wrap the seller wrapped the truck in. Same tools were used for that job.
Then I had to replace the string and hook. The string, which had to be so thin I had to borrow some of my grandmother's quilting thread to replace it with, was cut with my blade (for some reason, the scissors on both of my 91mm SAK's don't cut thread, only Wenger scissors do that job well, perhaps due to wear, as my Fieldmaster is ten years old, and my Craftsman's at least 25) then subsequently cut with my Wenger MicroLight Esquire's scissors.
The area where the winch drum was on the little wrecker was so cramped, I wouldn't have been able to do it without the Craftsman's tweezers (which was the smallest pair I had) which I used to thread the leangth of quilting thread through the pinhole sized securing eye on the winch drum. After tying the hook and thread on, I removed the excess string with the scissors.
-
I used my explorer to "repair" a lock my coworker has messed up.

The cam (translation right?) was on the wrong side. After a lot of confusion and a bit of chatting with RT, he said that there would be a splint that needed to be pushed down and could then be pushed around.
After some searching I found it:

I then used the corkscrew to push it down, because it was a bad angle and then the tiny screwdriver that's screwed in the corkscrew for the rest.
Using a future communicator stolen from the NCC-1701
-
I've been using the blades on both my new SAKs (Vic OHF and Wenger Esquire) to open various boxes at work.
Sent from my XT901 using Tapatalk
-
@Sweety-Sama said:
I used my explorer to "repair" a lock my coworker has messed up.
The cam (translation right?) was on the wrong side. After a lot of confusion and a bit of chatting with RT, he said that there would be a splint that needed to be pushed down and could then be pushed around.
After some searching I found it:

I then used the corkscrew to push it down, because it was a bad angle and then the tiny screwdriver that's screwed in the corkscrew for the rest.
Using a future communicator stolen from the NCC-1701
One of the more original uses of the corkscrew! :D

-
@cody6268 said:
I also collect older diecast toys/models and purchased a Dinky Supertoys 661 Scammell Explorer Recovery Tractor off of Ebay, which arrived yesterday. .First of all, I had to remove the foot diameter shroud of Saran wrap the seller used instead of a box. The scissors and blade on my Craftsman made (relatively) quick work of that.
Then I had to cut the bubble wrap the seller wrapped the truck in. Same tools were used for that job.
Then I had to replace the string and hook. The string, which had to be so thin I had to borrow some of my grandmother's quilting thread to replace it with, was cut with my blade (for some reason, the scissors on both of my 91mm SAK's don't cut thread, only Wenger scissors do that job well, perhaps due to wear, as my Fieldmaster is ten years old, and my Craftsman's at least 25) then subsequently cut with my Wenger MicroLight Esquire's scissors.
The area where the winch drum was on the little wrecker was so cramped, I wouldn't have been able to do it without the Craftsman's tweezers (which was the smallest pair I had) which I used to thread the leangth of quilting thread through the pinhole sized securing eye on the winch drum. After tying the hook and thread on, I removed the excess string with the scissors.
Your not allowed to mention Dinky Toys without there being pics

-
I just used the pliers on my MechaRogue to remove a shampoo bottle cap from some cover that didn't belong over it. My baby girl is having a bath and wanted them separated to play with the cap for some reason. The SAK pliers were perfect for the job as I couldn't have done it with my fingers.
Sent from my XT901 using Tapatalk
-
I used my Recruit (along with my son and other multitools!) to install the exhaust vent on our dryer.
-
Pants zipper was stuck to the bottom after washing it. SAK hook to the rescue!
-
Didn't get any in-action pics, but used the Phillips driver on my Outrider as an improvised ice pick at an afternoon cookout.

-
Used my Hercules to prune some branches off a little tree behind my house, then I used it to slice my finger, but that was less helpful.
-
Only thing it did was cut in half the muscle relaxers that my doctor gave me. Simple task for the Super Tinker.
-
I sharpened a pencil with the main blade on my Harvester, and used the awl to make some holes for wood screws. I may not have cared for it at first, but that that sak is starting to grow on me.
-
More harvester usage. Today I attacked the backyard with a weed wacker with my Harvester in my back pocket. The saw blade made short work of any weeds that were too thick to cut with the wacker. And when it needed more cord, the hawckbill blade was perfect for cutting a new length of cord off of the spool. This harvester is the perfect companion for fixing things up around the house.
-
I used the scissors on Classic to open a Taster's Choice instant pack. The day is young though....
-
Needed to rip down a piece of 2X4 to about 2 5/8" and cut it to size to support a window A/C. Farmer worked great as a scribe, to trim/whittle flat the ripped side and the saw off the block. Took about 20 min.

-
Deadheaded a load of flowers in the garden
Opened beer
-
So I up on an extension ladder removing oak tree "beards" and maple seeds which were matted on the screen over my rain gutter located above my deck. The gutter screen is screwed into the gutter in the front of the gutter and on the back side is held in place by friction. I found a photo online which shows the type of screen.
A poor design in my opinion.
I noticed the screen had dropped down in the gutter a couple of inches in several places on the back side. So I'm up in the air on a ladder trying to figure out what I could use to pull the screen back to where it should be. I pulled out my SAK Climber and found the hook would fit between the diamond shaped mesh and it worked perfectly to pull the mesh back into place.
I don't have any pictures of the hook in action, but I hope the powers that be will have sympathy on an older guy not wanting to get a camera and climb the ladder again to get a picture for a merit badge.

-
Watermelon tasting
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

