What did you use your Sak on today?
-
Pants zipper was stuck to the bottom after washing it. SAK hook to the rescue!
-
Didn't get any in-action pics, but used the Phillips driver on my Outrider as an improvised ice pick at an afternoon cookout.

-
Used my Hercules to prune some branches off a little tree behind my house, then I used it to slice my finger, but that was less helpful.
-
Only thing it did was cut in half the muscle relaxers that my doctor gave me. Simple task for the Super Tinker.
-
I sharpened a pencil with the main blade on my Harvester, and used the awl to make some holes for wood screws. I may not have cared for it at first, but that that sak is starting to grow on me.
-
More harvester usage. Today I attacked the backyard with a weed wacker with my Harvester in my back pocket. The saw blade made short work of any weeds that were too thick to cut with the wacker. And when it needed more cord, the hawckbill blade was perfect for cutting a new length of cord off of the spool. This harvester is the perfect companion for fixing things up around the house.
-
I used the scissors on Classic to open a Taster's Choice instant pack. The day is young though....
-
Needed to rip down a piece of 2X4 to about 2 5/8" and cut it to size to support a window A/C. Farmer worked great as a scribe, to trim/whittle flat the ripped side and the saw off the block. Took about 20 min.

-
Deadheaded a load of flowers in the garden
Opened beer
-
So I up on an extension ladder removing oak tree "beards" and maple seeds which were matted on the screen over my rain gutter located above my deck. The gutter screen is screwed into the gutter in the front of the gutter and on the back side is held in place by friction. I found a photo online which shows the type of screen.
A poor design in my opinion.
I noticed the screen had dropped down in the gutter a couple of inches in several places on the back side. So I'm up in the air on a ladder trying to figure out what I could use to pull the screen back to where it should be. I pulled out my SAK Climber and found the hook would fit between the diamond shaped mesh and it worked perfectly to pull the mesh back into place.
I don't have any pictures of the hook in action, but I hope the powers that be will have sympathy on an older guy not wanting to get a camera and climb the ladder again to get a picture for a merit badge.

-
Watermelon tasting
-
@kilowatt said:
So I up on an extension ladder removing oak tree "beards" and maple seeds which were matted on the screen over my rain gutter located above my deck. The gutter screen is screwed into the gutter in the front of the gutter and on the back side is held in place by friction. I found a photo online which shows the type of screen.A poor design in my opinion.
I noticed the screen had dropped down in the gutter a couple of inches in several places on the back side. So I'm up in the air on a ladder trying to figure out what I could use to pull the screen back to where it should be. I pulled out my SAK Climber and found the hook would fit between the diamond shaped mesh and it worked perfectly to pull the mesh back into place.
I don't have any pictures of the hook in action, but I hope the powers that be will have sympathy on an older guy not wanting to get a camera and climb the ladder again to get a picture for a merit badge.
I have used the hook for very similar purposes, hardware cloth, expanded metal, woven materials and the like. A very handy tool with much merit.

-
Been using my Marly Standard to help build a 1/144 scale Mig 31 Foxhound
-
2010 Soldier on a stick of biltong. Oh and a Gardiner too.....
My son insisted.They actually print "biltong knife" on the sides of the Gardiners here (well some at least). True story I can provide pics.

-
@kilowatt said:
So I up on an extension ladder removing oak tree "beards" and maple seeds which were matted on the screen over my rain gutter located above my deck. The gutter screen is screwed into the gutter in the front of the gutter and on the back side is held in place by friction. I found a photo online which shows the type of screen.A poor design in my opinion.
I noticed the screen had dropped down in the gutter a couple of inches in several places on the back side. So I'm up in the air on a ladder trying to figure out what I could use to pull the screen back to where it should be. I pulled out my SAK Climber and found the hook would fit between the diamond shaped mesh and it worked perfectly to pull the mesh back into place.
I don't have any pictures of the hook in action, but I hope the powers that be will have sympathy on an older guy not wanting to get a camera and climb the ladder again to get a picture for a merit badge.
Sympathy no, appreciation for your ability to link to a post yes.
We use a similar mesh here and fasten it to both the gutter and the roof. -
One of my other hobbies is RC trucks.
The body clips on the 1/8 scale ones can be pretty thick. Usually, I end up either bending them up to make them easier to grab ahold of, or put a twist tie or zip tie on them.
But I hadn't done it yet and one time last week, my fingers were sweaty and I couldn't get the !@#$% things out to change batteries. It was then that I remembered the Super Tinker in my pocket, whose hook saved the day!
Here's the truck in question, with my 3 year-old for scale: (It's a Kyosho Mad Force Kruiser 2.0VE, if you're curious)
-
Nice!

-
Very cool!
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login



