And so it begins.... (My adventures into Alox!)
-
@Syph007 said:
The customer that bought my liner lock farmer modded my mod and made it better. The ver 2 of the liner lock still needs some tweaking as it can be awkward to activate it. He dremeled out a scallop in the back scale and said it now works like a dream. When I make version 3 I will make the thumb grip area higher.
Looks great, the only downer on that whole setup looks to be that it will rub the "Vic" name off in due time.. Any locking blade, besides the oldschool back lock ones have a little ball that glides across the blade, small as heck and I have no clue how it stays in, but just an idea?
JR -
The customer that bought my liner lock farmer modded my mod and made it better. The ver 2 of the liner lock still needs some tweaking as it can be awkward to activate it. He dremeled out a scallop in the back scale and said it now works like a dream. When I make version 3 I will make the thumb grip area higher.

Looks great, the only downer on that whole setup looks to be that it will rub the "Vic" name off in due time.. Any locking blade, besides the oldschool back lock ones have a little ball that glides across the blade, small as heck and I have no clue how it stays in, but just an idea?
JRYa most liner locks use a detent ball that holds blade from wobbling free in closed mode. Since this still has a backspring that holds it closed I dont need that. From what I understand though you drill a precise hole then press fit them in.
-
The customer that bought my liner lock farmer modded my mod and made it better. The ver 2 of the liner lock still needs some tweaking as it can be awkward to activate it. He dremeled out a scallop in the back scale and said it now works like a dream. When I make version 3 I will make the thumb grip area higher.

Looks great, the only downer on that whole setup looks to be that it will rub the "Vic" name off in due time.. Any locking blade, besides the oldschool back lock ones have a little ball that glides across the blade, small as heck and I have no clue how it stays in, but just an idea?
JRYa most liner locks use a detent ball that holds blade from wobbling free in closed mode. Since this still has a backspring that holds it closed I dont need that. From what I understand though you drill a precise hole then press fit them in.
I always thought that was to have less of a rub when opening and closing the blade.
JR -
The customer that bought my liner lock farmer modded my mod and made it better. The ver 2 of the liner lock still needs some tweaking as it can be awkward to activate it. He dremeled out a scallop in the back scale and said it now works like a dream. When I make version 3 I will make the thumb grip area higher.

Looks great, the only downer on that whole setup looks to be that it will rub the "Vic" name off in due time.. Any locking blade, besides the oldschool back lock ones have a little ball that glides across the blade, small as heck and I have no clue how it stays in, but just an idea?
JRYa most liner locks use a detent ball that holds blade from wobbling free in closed mode. Since this still has a backspring that holds it closed I dont need that. From what I understand though you drill a precise hole then press fit them in.
I always thought that was to have less of a rub when opening and closing the blade.
JRYep it serves that purpose too.
Found a good youtube video talking about them.
- YouTube
Auf YouTube findest du die angesagtesten Videos und Tracks. Außerdem kannst du eigene Inhalte hochladen und mit Freunden oder gleich der ganzen Welt teilen.
(www.youtube.com)
-
[quote author=Syph007 link=topic=34772.msg1111276#msg1111276 date=1435499608]
The customer that bought my liner lock farmer modded my mod and made it better. The ver 2 of the liner lock still needs some tweaking as it can be awkward to activate it. He dremeled out a scallop in the back scale and said it now works like a dream. When I make version 3 I will make the thumb grip area higher.
Looks great, the only downer on that whole setup looks to be that it will rub the "Vic" name off in due time.. Any locking blade, besides the oldschool back lock ones have a little ball that glides across the blade, small as heck and I have no clue how it stays in, but just an idea?
JRYa most liner locks use a detent ball that holds blade from wobbling free in closed mode. Since this still has a backspring that holds it closed I dont need that. From what I understand though you drill a precise hole then press fit them in.
I always thought that was to have less of a rub when opening and closing the blade.
JRYep it serves that purpose too.
Found a good youtube video talking about them.
https://www.youtube.com/watch?v=TYsnQrGg6TY
[/quote]
Yeah, in your case it wouldn't be needed, since it holds in the closed position, but just for a easy glide while opening and closing, but if you really think about it wouldn't really do anything since the sak is a two hand open no matter what, unlike any other lock blade where it's a one hand open..
JR -
Looks like I need to send you a Syph mod and some cash to upgrade it!
Too sweet!
-
Hey Syph, if I was looking for a slim, bladeless 93mm sak that featured a saw, a cap lifter, an inline phillps and an awl, could the awl sit opposite the inline phillips next to the cap lifter?
-
@MachoGrande said:
Hey Syph, if I was looking for a slim, bladeless 93mm sak that featured a saw, a cap lifter, an inline phillps and an awl, could the awl sit opposite the inline phillips next to the cap lifter?Yes im sure i did that configuration before and it should work.
-
Finally the 93mm rescue blade SAK mod is together! :D
The Ti liner lock worked out well on this, but I had a big issue getting the blade normal big blade on there. The nail nick points inside so running out of ideas I just ground a nail nick on the other side so it could be opened. Luckily that worked out just fine!








-
Now that is pretty bad a$$! Nice job Syph!
JR -
@MadPlumbarian said:
Now that is pretty bad a$$! Nice job Syph!
JRI can only second that... it has turned out prettier than a Disney Princess.

I will call this model ALPINIST, as this is its intended purpose.
-
Can someone school me on the liners that seperate tools. That last mod has the saw and file butted right up to one another. Do liners just provide room to get to the nail nicks, or do they serve another purpose?
-
@tommywp said:
Can someone school me on the liners that seperate tools. That last mod has the saw and file butted right up to one another. Do liners just provide room to get to the nail nicks, or do they serve another purpose?They provide stength to the frame and work against the resistance of the backsprings. If you were to say build a swisschamp and leave out all liners, the inner tools would have zero snap and the pins would be bowed. But thin tools you can get away with putting a couple per layer.
-
Can someone school me on the liners that seperate tools. That last mod has the saw and file butted right up to one another. Do liners just provide room to get to the nail nicks, or do they serve another purpose?
They provide stength to the frame and work against the resistance of the backsprings. If you were to say build a swisschamp and leave out all liners, the inner tools would have zero snap and the pins would be bowed. But thin tools you can get away with putting a couple per layer.
Interesting, thanks. Nice work, as always.
-
These are Ti scale blanks that I manually textured on my mill today as a test. I think they'll look pretty sweet anodized and with the upper surface sanded shiny.... :D
-
They do look good syph, here's an idea, idk if it would be possable but if so what about a mini diamond plate pattern? Now that would be cool!
JR -
@Syph007 said:
Well I did some kind of chemistry here by accident...
The center was polished brass and I wanted to anodize the rest blue... didnt quite work, but its interesting.

This, for me, is still the most beautiful scale you made so far. Can you replicate this "accident"? If I ever get the funds, I'll be asking you to build me a SAK with this cross.

-
Well I did some kind of chemistry here by accident...

The center was polished brass and I wanted to anodize the rest blue... didnt quite work, but its interesting.

This, for me, is still the most beautiful scale you made so far. Can you replicate this "accident"? If I ever get the funds, I'll be asking you to build me a SAK with this cross.

Im sure i could do it again ya. The anodize part was good, but I didnt care for the brass turning black.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
