My First Alox Mod.
-
Today i received really nice condition pliers,fron NKB Neil.
Thanks man.a lot!

-
So you'll be done soon then?
:D -
no man,im waitin to get pins and somethin.
i was thinking of puttin somethin else to hang it,get rid of split ring,and maybe bend a u-shaped stainless steel,or brass wire,with flattened ends and holes....and put this on the other end,between pin and scale.
-
heres the pliers and alox saw backsprings,the pliers had been drilled to 3.05mm(that was a tough job just like ive been told,took me four cheap diamond drills)and u can see that the pliers really dont fold even near to the closed-position,the handles end jams against backspring causing this:


SO,i just cut up the end,some 4 mm´s away and tried it again:

the gap went smaller:

so,i cut the handles more,like a really rough rounding:

and it got really near is proper position,the pliers i mean.
so i just started to smoothen the handle and round it more:

gave it a bit of a polish:

and hers a few more shots:

here its ready,well almost;).i had to grind the landing spots flat,in the backspring so the pliers sit now very nicely against spring when closed.
here its in open position:

and one with liner in place,to show better the size and positions of pliers compared to outlines af 93 alox:

-
Looking good

How come your work area is so clean though ??? Where's all the swarf and piles of junk? Or is that just me
What are your plans for the phillips driver; what are you putting opposite it?
Neil
-
@NKB said:
Looking good
How come your work area is so clean though ??? Where's all the swarf and piles of junk? Or is that just me
What are your plans for the phillips driver; what are you putting opposite it?
Neil
you hit the spot with that question,im thinkin that too,as i really dont put a magnifyin glass into my knife,and that plastic appearance would ruin it in my eyes.if theres no other options,i guess im goin to have to make a thicker copy of those splitring holding spacers to make it work.
about my work area?well actually that is my bar table,since i live in this old factory where ive done myy home,u might call these apartements"loft"-style.so its just an old bar from a bar :D,that acts like my working table too sometimes for these minor jobs.all the dirty work i do at our clubhouse or at school,except for airbrush,pinstripe,and tattoo things,i have a room for those here.and i like to keep it clean,and so does my girlfriend >:D.
-
dont worry Neil,i do have piles next to piles of junk but i put em in small boxes and so on,im the kind of guy that id loose all if my table would be filled with stuff,and id be droppin them onto floor etc,and as we have cats and dogs,they would eat or stash em :D,and id hate to use some tweezers to find some little part from dogs pile. :D
-
Its your knife but I have a question (even though I doubt Ill ever try it). Could you put the Phillips driver opposite the flat/bottle opener, eliminate the small knife in favor of a saw....or won't the two drivers fit together.
-
i wish it would be possible man,too.
but the phillips is so wide all the way,and long that it hits to can opener/small flattie nad also to the big flattie/cap lifter too.those two seem to work best in same layer together but i donno anythin else to cope with my phillips,than magnifying glass and im not goin to put it in.id rather make a spacer with ring attachment to the place of magnifier.
wenger has this cool little wrench that i think might be ok,with some modifications.....
-
The little Wenger wrench might work, its a bit thinner than the Vic. phillips so you'd still need a spacer. Having a very casual look at both tools I think they are a bit too long to go together on a 93mm frame.
How about making some kind of shackle to fit opposite the phillips? Something that can be folded out for carry and then slotted back in to the knife whilst you're using it? A bit like this...

Neil
-
yep,that would be actually very nice idea,Neil

i think the next mod im a bout do do(in a world of sak) will be wenger caus ei like so much some of their implements like that snap shackle,wrench,dedicated can opener,and they have pliers too ive understood.and serrated blades >:D
-
Great work on those pliers mate. :)
-
thanks Ben,and as i get to the point where i can hammer the rivets down finally,ill polish all of the surfaces better for even looks.
-
Looking good!

-
Thanks for the pr0n. Looking good!
Oh no. I'm starting to feel something...
I hope I don't catch this SAK modding bug going around. =(
-
I wish i could catch the SAK modding craze thats going round, i'm very envious of these mods but i don't have the tools, space or know how to do them! I'm enjoying your work though, it's looking extremely impressive so far!
-
thanks man,i appreciate your opinion,since this is the first ive ever done on sak.

today i received pin material,more saw springs,drill bits,spacer brass etc from Bill / Scibeer,so i can continue my job.
Thanks Mr.Scibeer for your support & parts.
-
So do you have everything now?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

