My First Alox Mod.
-
Its your knife but I have a question (even though I doubt Ill ever try it). Could you put the Phillips driver opposite the flat/bottle opener, eliminate the small knife in favor of a saw....or won't the two drivers fit together.
-
i wish it would be possible man,too.
but the phillips is so wide all the way,and long that it hits to can opener/small flattie nad also to the big flattie/cap lifter too.those two seem to work best in same layer together but i donno anythin else to cope with my phillips,than magnifying glass and im not goin to put it in.id rather make a spacer with ring attachment to the place of magnifier.
wenger has this cool little wrench that i think might be ok,with some modifications.....
-
The little Wenger wrench might work, its a bit thinner than the Vic. phillips so you'd still need a spacer. Having a very casual look at both tools I think they are a bit too long to go together on a 93mm frame.
How about making some kind of shackle to fit opposite the phillips? Something that can be folded out for carry and then slotted back in to the knife whilst you're using it? A bit like this...

Neil
-
yep,that would be actually very nice idea,Neil

i think the next mod im a bout do do(in a world of sak) will be wenger caus ei like so much some of their implements like that snap shackle,wrench,dedicated can opener,and they have pliers too ive understood.and serrated blades >:D
-
Great work on those pliers mate. :)
-
thanks Ben,and as i get to the point where i can hammer the rivets down finally,ill polish all of the surfaces better for even looks.
-
Looking good!

-
Thanks for the pr0n. Looking good!
Oh no. I'm starting to feel something...
I hope I don't catch this SAK modding bug going around. =(
-
I wish i could catch the SAK modding craze thats going round, i'm very envious of these mods but i don't have the tools, space or know how to do them! I'm enjoying your work though, it's looking extremely impressive so far!
-
thanks man,i appreciate your opinion,since this is the first ive ever done on sak.

today i received pin material,more saw springs,drill bits,spacer brass etc from Bill / Scibeer,so i can continue my job.
Thanks Mr.Scibeer for your support & parts.
-
So do you have everything now?
-
yep i do,atleast it really looks like ive got all i need.the only thing to get,or actually to fabricate is that splitring attachment spacer,that is to be made as thick as the phillips is,to put to the opposite end of the layer where that phillips is,since i havent figured out any good solution to that,and plastic magnifier glass is NOT an option.
:D
-
Is it done yet? 
Pics please ;)
Neil
-
no its not man,im so sorry to disappoint you :D
tomorrow ill have day off from school and im plannin to spend few hours workin on that.do u know i received three saw back springs,and now i could put saw too in it,i think that wouldnt be too much yet,but nothin more anymore so the setup would be:
-electrician blade
-awl
-pliers
-c opener
-b opener
-sawi think thats enough and keeps it still thin enough....4 layers.
-
Are you just having the electricians blade?
-
just?
i could easily do withoutany blade
:D :D :D :Dyep,im not puttin any other blade in it since i dont have spare serrated big blade >:D
or what did u have in mind?
-
I just thought you were going to put the normal plain edge in as well.
-
I hate to bring it up again (and add work) but how close is the fit between the Phillips and flat head? If its close couldn't you shave some off the flat driver and still have it be just as effective? That way you could eliminate a layer (or add a saw). With or without the saw I hope someone pays attention to your work, that pliers on a thinner SAK is near perfection....at least for me.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

