firearms
-
Nice but very expensive. I gather many do not like my taste in grips. :D
Well in the process of cleaning some 9 mm brass found on the range (2 visit pick up). Thank you local police force and folks who don't roll their own ammo. At this rate, I may never have to buy brass again.
This is several hours in the rotary tumbler being attacked by corn bits.
Next step, my sonic cleaner full of Lyman Turbo Case Clean.
-
These guys are hard to beat for fancy wood grips.
Amazing site!
So what did you order SG?
Nothing, I'm fixed for grips in fact have more grips than guns now.....

Chako, I like 'em fine!

I'd put stag on mine if I could afford it but I reckon these will do..... :D
-
These guys are hard to beat for fancy wood grips.
Amazing site!
So what did you order SG?
Nothing, I'm fixed for grips in fact have more grips than guns now.....

Chako, I like 'em fine!

I'd put stag on mine if I could afford it but I reckon these will do..... :D
Gold Cup SG?
-
[quote author=buck link=topic=53984.msg1139173#msg1139173 date=1439903693]
These guys are hard to beat for fancy wood grips.Amazing site!
So what did you order SG?
Nothing, I'm fixed for grips in fact have more grips than guns now.....

Chako, I like 'em fine!

I'd put stag on mine if I could afford it but I reckon these will do..... :D
Gold Cup SG?
[/quote]Nah, I stupidly sold that! (
) Just a very early Series 80 that's a twin to a Series 70. Only diffs are a lowered ejection port and the firing pin safety. I swapped out the collet bushing for a Brown Precision solid one and bought the conversion kit to return it to a Series 70 firing pin config.I got rid of my GC because I kept walking out the Colt Elliason rear sight pin shooting hardball at the combat matches.....went with a fixed sight model.
-
As a Glock owner, I am jealous of 1911 owners for only one reason- your guns can wear jewelry. Love some of those scales. Cheapier than dressy grips for a revolver by a lot usually.
So, I don't normally comment in this thread, and I don't normally shill, but I got a gadgety bit in the mail today. http://www.mygtul.com/product/gtul-9mm40sw
I have small hands and shorter than proportional thumbs. As a result, it's hard for me get enough squeeze on a magazine body to clean it, and I have damaged a magazine to the point where all I could was salvage the baseplate, follower and spring after squeezing too hard with channel locks. Normally, getting a baseplate off is a three, four minute streak of swearing and grunting. This widget let me pull a magazine apart in under a minute, without swearing, and it isn't one of my half worn out KCIs but an almost brand new, loaded and fired twice OEM magazine I picked up last week. Seriously a better use of the money than a box of plinking ammo if you own a Glock.
-
Interesting. I didn't know they made an item like that. My M&P magazines come apart very easily. Just press the center button with something long like your grip retention rod, and slide the base plate out of the way meanwhile being carful to catch the spring and sub assembly before they fly out across the room. Yeah, my first disassembly was somewhat entertaining. :D
Edit. Yay! Looks like the 1911 is now on its way. Just got confirmation from Canada Post that it is in transit.
-
I can't wait to get my somewhat birthday gift in. I did get a letter from the RCMP stating ownership transfer of the Norinco 1911A1. Info from Canada Post tells me I should get it by next Wednesday if all goes right.
-
@Chako said:
Interesting. I didn't know they made an item like that. My M&P magazines come apart very easily. Just press the center button with something long like your grip retention rod, and slide the base plate out of the way meanwhile being carful to catch the spring and sub assembly before they fly out across the room. Yeah, my first disassembly was somewhat entertaining. :D+1
Maybe Glock magazines are assembled differently, but on most of my mags depressing a pin in a hole on the baseplate allows the baseplate to slide right off. A small screwdriver (or sometimes a small cleaning rod) is all that's needed. Reassembly can sometimes be tricky, with the magazine spring refusing to cooperate. The major thing though is to make sure you've reinstalled the follower correctly.
1911 mags can also be disassembled, though the process is substantially different and somewhat tricky. Just make sure you don't mess with the feed lips.
-
Interesting. I didn't know they made an item like that. My M&P magazines come apart very easily. Just press the center button with something long like your grip retention rod, and slide the base plate out of the way meanwhile being carful to catch the spring and sub assembly before they fly out across the room. Yeah, my first disassembly was somewhat entertaining. :D
+1
Maybe Glock magazines are assembled differently, but on most of my mags depressing a pin in a hole on the baseplate allows the baseplate to slide right off. A small screwdriver (or sometimes a small cleaning rod) is all that's needed. Reassembly can sometimes be tricky, with the magazine spring refusing to cooperate. The major thing though is to make sure you've reinstalled the follower correctly.
**
1911 mags can also be disassembled, though the process is substantially different and somewhat tricky. Just make sure you don't mess with the feed lips.**+100
-
Just found this video. Apparently Glocks have an additional step I've never encountered on any other magazine. Probably just as well I've never owned a Glock; would have busted a magazine trying to get it apart. :D
- YouTube
Auf YouTube findest du die angesagtesten Videos und Tracks. Außerdem kannst du eigene Inhalte hochladen und mit Freunden oder gleich der ganzen Welt teilen.
(www.youtube.com)
-
I have a Walther TPH in .22LR that uses similarly designed magazines that rely on a plastic lip hanging onto the base. After years of intermittent back pocket carry the plastic lip crumbled off rendering it a single shot. Poor design if you ask me.
Looking for a replacement magazine revealed they were rare and shockingly expensive in .22 but just the opposite for .25. I bought the .25 TPH magazine (and a spare) and cannibalized its baseplate onto my .22 magazine and now all is again well.
This Walther TPH .22 is always in my back pocket when in the boonies such as dove hunting. I can carry a bunch of ammo and could use it for signaling (I'm somewhat disabled) or punching cans if the hunt is a bust and I'm bored.
-
@buck said:
I have a Walther TPH in .22LR that uses similarly designed magazines that rely on a plastic lip hanging onto the base. After years of intermittent back pocket carry the plastic lip crumbled off rendering it a single shot. Poor design if you ask me.Looking for a replacement magazine revealed they were rare and shockingly expensive in .22 but just the opposite for .25. I bought the .25 TPH magazine (and a spare) and cannibalized its baseplate onto my .22 magazine and now all is again well.
This Walther TPH .22 is always in my back pocket when in the boonies such as dove hunting. I can carry a bunch of ammo and could use it for signaling (I'm somewhat disabled) or punching cans if the hunt is a bust and I'm bored.
My Beretta 21 had a similar role. Snake gun these days.

-
I have a Walther TPH in .22LR that uses similarly designed magazines that rely on a plastic lip hanging onto the base. After years of intermittent back pocket carry the plastic lip crumbled off rendering it a single shot. Poor design if you ask me.
Looking for a replacement magazine revealed they were rare and shockingly expensive in .22 but just the opposite for .25. I bought the .25 TPH magazine (and a spare) and cannibalized its baseplate onto my .22 magazine and now all is again well.
This Walther TPH .22 is always in my back pocket when in the boonies such as dove hunting. I can carry a bunch of ammo and could use it for signaling (I'm somewhat disabled) or punching cans if the hunt is a bust and I'm bored.
My Beretta 21 had a similar role. Snake gun these days.

Very James Bond of you! Does it have the tip up barrel?
-
I have a Walther TPH in .22LR that uses similarly designed magazines that rely on a plastic lip hanging onto the base. After years of intermittent back pocket carry the plastic lip crumbled off rendering it a single shot. Poor design if you ask me.
Looking for a replacement magazine revealed they were rare and shockingly expensive in .22 but just the opposite for .25. I bought the .25 TPH magazine (and a spare) and cannibalized its baseplate onto my .22 magazine and now all is again well.
This Walther TPH .22 is always in my back pocket when in the boonies such as dove hunting. I can carry a bunch of ammo and could use it for signaling (I'm somewhat disabled) or punching cans if the hunt is a bust and I'm bored.
My Beretta 21 had a similar role. Snake gun these days.

Very James Bond of you! Does it have the tip up barrel?
But of course!!! 8) -
I had a nickel Beretta model 21 in the 80's. I remember killing a water moccasin on the road bridge onto our salt marsh island where we hunted ducks back then. I used CCI snake shot and it did the job though it would not cycle the next round which was ok for that gun with the tip up barrel.
I couldn't barely see the teeny sights and therefore couldn't hit dodo with it.
-
@buck said:
I had a nickel Beretta model 21 in the 80's. I remember killing a water moccasin on the road bridge onto our salt marsh island where we hunted ducks back then. I used CCI snake shot and it did the job though it would not cycle the next round which was ok for that gun with the tip up barrel.I couldn't barely see the teeny sights and therefore couldn't hit dodo with it.
Their recoil spring is pretty heavy...mine won't cycle snake shot either which is probably normal. My 21 sights are exactly on at about 3 feet which is perfect for snakes...I have to sit the whole front blade in the rear notch to hit out at about 10 yards. Had this one about 25 years. my Ex has a Mod 20 in 25ACP that I got her back in the early 80's. Never a problem with either one. My MIL's Sterling 25 cracked a plastic mag baseplate about 15 years ago....I was able to find one online and replace it for her.
-
-
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
















