The SwissTool owners club
-
Finished touching up the RS I recently got. It's got a good heft to it, especially when working with it.
It's either I haven't sharpened the PE blade properly or I shouldn't expect it to be as razor sharp as say, a LM Sidekick blade?
-
Finished touching up the RS I recently got. It's got a good heft to it, especially when working with it.
It's either I haven't sharpened the PE blade properly or I shouldn't expect it to be as razor sharp as say, a LM Sidekick blade?
It should get razor sharp. ;)
Got it! Thanks!
Had to do a few more swipes with the sharpener and I think I may have gotten it right already!
-
Finished touching up the RS I recently got. It's got a good heft to it, especially when working with it.
It's either I haven't sharpened the PE blade properly or I shouldn't expect it to be as razor sharp as say, a LM Sidekick blade?
It should get razor sharp. ;)
Got it! Thanks!
Had to do a few more swipes with the sharpener and I think I may have gotten it right already!
It won't get as razor sharp as a Leatherman blade unless you re-grind the primary bevel. Leatherman uses a much shallower primary bevel angle, which I then put a 40° secondary (working) bevel on. It's very easy with Leatherman. Not hard with Vic, but not as easy as with LM.
-
I've sharpened LM and Wenger blades without a problem. Wenger, I think just because the blades are generally thinner to start with and LM, that secondary bevel mentioned above. I've never had great luck sharpening Vic blades, but I am by no means a sharpening expert.
-
Finished touching up the RS I recently got. It's got a good heft to it, especially when working with it.
It's either I haven't sharpened the PE blade properly or I shouldn't expect it to be as razor sharp as say, a LM Sidekick blade?
It should get razor sharp. ;)
Got it! Thanks!
Had to do a few more swipes with the sharpener and I think I may have gotten it right already!
It won't get as razor sharp as a Leatherman blade unless you re-grind the primary bevel. Leatherman uses a much shallower primary bevel angle, which I then put a 40° secondary (working) bevel on. It's very easy with Leatherman. Not hard with Vic, but not as easy as with LM.
Wow, that does make a lot of sense. I guess the most I can sharpen the PE blade is equal to how a Rebar's PE blade is.
-
If there's another thing I learned from all of this, it's to use the flathead as the pry tool instead of the PE blade. One may argue that the knife blade can get into tighter areas but then there's the chisel- easier to maintain and as good as a follow thru as a flathead.
Currently using it to fix a defective light switch by the landing at the stairs.
-
Hi!
I'm here playing with my SwissTool RS and notice it's difficult to get the blade out due to how far it is recessed. No idea if it has always been this way or not - as I just cut my nails short (using the scissors on it, of course).
Follow SwissTool connoisseurs, is this normal? Picture attached for context :)

-
Mine's like that too.
-
Not sure if I ever joined this club...
I have 3. 1 in BO and in transit and 2 in SS.
Here's a shot of one of my SS ones with some friends.
-
Just in....
-
I carried the Swisstool Spirit for a long time last summer and used for small in-house-repairs tool. But it seems that there is some loosening on each of the tools, as well as on the pliers. I will have to send it in for replacing the philipsheadscrewdriver and tightening the whole tool.

It sucks somehow as it seems be very well put together; the finish is just superb for a MT. No big use for me for the tool right now. I really have to send it in.
-
@Humppa said:
I carried the Swisstool Spirit for a long time last summer and used for small in-house-repairs tool. But it seems that there is some loosening on each of the tools, as well as on the pliers. I will have to send it in for replacing the philipsheadscrewdriver and tightening the whole tool.

It sucks somehow as it seems be very well put together; the finish is just superb for a MT. No big use for me for the tool right now. I really have to send it in.
Wow Andi!! That's really unusual for one to do that. :o
-
Yes, unusual indeed.
And I doubt that it was due to some hard use. The philipshead on mine was rather soft steel and showed some wear even after some tightened srews. As I said, I doubt I tourqued too hard. The whole tool seems to rattle like cow-tail (as we use to say here).
Maybe I can get it back well repaired and it will last forever that way. But I suspect that I only got a monday´s tool.

-
threads still going after almost 6 years.

-
Join with spirit that updated to plus set

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

