Double (large) blade Victorinox Compact
-
Another idea I'm having is just add scissors to the Spartan and replace the cork screw with a Phillips to make a serrated Super Tinker.
-
You'll end up with lots of blades. Why not put a nailfile instead of the small blade? Is it too thick?
I'd keep the hook, but that's me. I find it useful.

-
@pfrsantos said:
You'll end up with lots of blades. Why not put a nailfile instead of the small blade? Is it too thick?I'd keep the hook, but that's me. I find it useful.

I like a small blade and tend to use it more. I've even thought about what kind of configuration could be made by replacing the large blade with something else and only have a pen blade. No use it exposing oneself to a large blade unless needed. I think the small blade complements the large serrated blade nicely.
-
@kosmo said:
I've been thinking of another Compact mod. I just received a serrated Spartan and I've been thinking of making a double (large) blade Compact. Because of access to some of the tools, I'll need to stagger the blades with scissors in the middle.Layer
- Large serrate blade / small pen blade
- Scissors
- Large blade / Combo tool
On the back side I'll have three locations for back side tools. Either I am going to use an older scissors back spring with no backside tool and have an empty slot. Or I am thinking of using two back springs with back side tool slots and removing some of the liner between the two back springs and include the Phillips driver. To give you some idea, I've included the photo below. Taking some measurements with calipers for width and depth of the slots, I believe there is room to do this, if I remove some material from a liner. Does anyone see other problems that might arise?

I did a similar concept on my Mega84 mod. Check out that thread for the issues I encountered. Feel free to give me a yell with any questions

-
Ive been thinking of doing a similar mod for a few days now, so im very excited to see how yours turns out. Good luck!
-
You could do what Syph did on one of his and reposition the philips?
-
Looking forward to the outcome of that exercise!

-
<u></u>
@tattoosteve99 said:
You could do what Syph did on one of his and reposition the philips?Wow, Syph has done so much stuff, I'm not sure I remember. I recall seeing one with both cork screw and phillips located on opposite sides.
I would be OK with just replacing the cork screw with a phillips. I'm just wondering what I might do considering I'm using a second main blade back spring and have an opportunity to install some kind of additional back side tool. What else would work well in a main blade back side tool that is only one layer wide? It would have to match the width of the back spring.
-
Bob (Syph) overcame the problem of getting the Phillips to fit by milling it down a bit, I added an extra spacer insted (which helped with other issues too). As to adding an alternate tool instead of the Phillips, all the other back tools will be thinner, so it's just a matter of adding the right thickness washers
-
@50ft-trad, @tattoosteve99
Found Syph's post on the phillips mod. It a little too much than I can handle doing without a mill. Nice idea though.
/post/1145625
-
I like your original plan. Cut the hook and use the base to tension the scissors, cut the liner to allow the phillips. And take lots of pics.

-
@zoidberg said:
I like your original plan. Cut the hook and use the base to tension the scissors, cut the liner to allow the phillips. And take lots of pics.
Your right. I'm going to have to cut the hook or make some kind of spacer to keep the tension.
I would have eventually realized that, probably on assembly. :D -
I've done it several times on 84s using the blind backspring from the Recruit. I usually put a wood saw in between.
I've done it on Wengers as well...but using the tang of the corkscrew for a spacer...




-
I did a "Double Recruit" mod a while back, i also have a genuine a Wenger "Double Blade".

-
Here's the link for the one I did....
/post/1144091
-
I recall doing a trial assembly on a 91 that incorporated corkscrew and Phillips un-modified. Added extra liners (I think 3) to create space for the offset of the Phillips. Never went through with it...but the plan was to make a thick one-piece liner for final assembly.
-
Found pics...



-
I also thought that the thick spacer might provide the opportunity to add slots for pull-out tools...like a diamond needle file for sharpening.
-
Found this one where Syph thinned down the phillips so it's kind of like the Leatherman bit driver phillips:

Could be an interesting alternative.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login