Show off your Sak mod's!
-
Titanium Tool 58mm
-
Pioneer with Scissors Burnt Bronze Cerakote. Titanium screws. Brass liners.
-
Nice one ALM

Sent from my SM-G920R4 using Tapatalk
-
I have one ALM custom and it is amazing!! Now the problem is the more of his work I see the more I want!
-
-
-
@hiraethus said:
Making some brass liners for Pioneers

I like the work pics.

-

I should have taken more, but only managed to snatch a bit of time in the evenings to make a start on these. The process is a bit laborious, but it's nice when they start to really take shape like this.
-
That's one thick liner right there! :o :D

-
:D It's 9 or 10 liners all stacked up so I can shape them in one go. TBH it's a bit thick for my belt sander and fret saw to handle - I'd be better off doing them 4 or 5 at a time.
-
Fret saw? You're cutting them manually?!
I'm both jealous and inspired. I'll mod me a SAK or three, one day

-
-
@firiki said:
Fret saw? You're cutting them manually?!I'm both jealous and inspired.

Yep, all manual - except for the belt sander.
The way I do it is:
Cut the blanks using tin snips (21 mm x 100 mm or so) out of 0.8 mm brass sheet.
Flatten the blanks as they get bent during cutting.
Drill and deburr one pivot hole in each blank.
Stack the liners and clamp together with a single factory liner as a drilling template, using a 3mm pin through the already drilled hole as location.
Drill the other two holes in the stack - this ensures that they're all in the same place.
Separate out the stack and deburr the holes as necessary
Rebuild the stack with a factory liner at each end to act as a guide for the sanding - bolt and rivet together tightly.
Hacksaw as much material from the outside as possible.
Use belt sander to get the outer edges close to the liners.
Use a combination of hack and fret saw to remove the material from the middle.
Belt sand the bits in the middle you can get to.
Keep going at the shaping with files until very close to the shape of the factory liners, then switch to aluminium oxide/silicon carbide paper and polish to finish.You really should.

-
Fret saw? You're cutting them manually?!
I'm both jealous and inspired. I'll mod me a SAK or three, one day

Yeah, a SAK of mass destruction
And I'll call it magentus' silence (at last)...
will it have a fish scaler?
Yes, it is useful in pic-nics and other occasions. It will be called magentus' sorrow

-
Fret saw? You're cutting them manually?!
I'm both jealous and inspired.

Yep, all manual - except for the belt sander.
The way I do it is:
Cut the blanks using tin snips (21 mm x 100 mm or so) out of 0.8 mm brass sheet.
Flatten the blanks as they get bent during cutting.
Drill and deburr one pivot hole in each blank.
Stack the liners and clamp together with a single factory liner as a drilling template, using a 3mm pin through the already drilled hole as location.
Drill the other two holes in the stack - this ensures that they're all in the same place.
Separate out the stack and deburr the holes as necessary
Rebuild the stack with a factory liner at each end to act as a guide for the sanding - bolt and rivet together tightly.
Hacksaw as much material from the outside as possible.
Use belt sander to get the outer edges close to the liners.
Use a combination of hack and fret saw to remove the material from the middle.
Belt sand the bits in the middle you can get to.
Keep going at the shaping with files until very close to the shape of the factory liners, then switch to aluminium oxide/silicon carbide paper and polish to finish.You really should.

I'm certainly eager but if this is to happen radical changes must be made in my life first. Like, getting a bench to work on and getting some more tools and a place to put said bench, also finding the time. Baby is the top priority right now though, things are tough I can tell you. Alternatively, if only I could manage to be granted free access to a friend's workplace...
Thanks for the description of the process
I'm not sure if you're encouraging me or demoralising me, though. :D -
Totally understand about the time kids need, and hope that all's well.
You don't need much to get started with modding, particularly if you're doing cellidor stuff - a drill, some files, punches and a hammer will do to start with. You could use my tools anytime you like, but I guess it's not that convenient. Time seems to be my most precious commodity.
-
@hiraethus said:
Totally understand about the time kids need, and hope that all's well.You don't need much to get started with modding, particularly if you're doing cellidor stuff - a drill, some files, punches and a hammer will do to start with. You could use my tools anytime you like, but I guess it's not that convenient. Time seems to be my most precious commodity.
What H says.
For basic modding you really don't need much at all in the way of tools. Time is what you need and parenthood doesn't come with an Hermione Granger 'Time Turner'.
Drop your end of times shenanigans though and you'll have plenty of time for modding. :D
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
