Show off your Sak mod's!
-
Thank you all for the info, I have a local hobby shop or two that needs visiting...
I had seen the Apprentice but unfortunately also saw the prices some bring! Figured I'd probably spend twice as much, bugger a couple perfectly serviceable knives, curse a bit, and try to make my own... :) -
@hiraethus said:
DIY Modeler:

Top job H!

-
@Sheradin said:
Thank you all for the info, I have a local hobby shop or two that needs visiting...
I had seen the Apprentice but unfortunately also saw the prices some bring! Figured I'd probably spend twice as much, bugger a couple perfectly serviceable knives, curse a bit, and try to make my own... :)Yea, some of those out of production SAKs get crazy expensive. I was lucky enough to have someone give me a beat up Apprentice I was able to get back to functional but I'll probably make up some too. Even though the Apprentice is compact and has a great tool set, the backside phillips has some limitations on strength so I'll likely make up some Scientists. That's another out of production and crazy priced SAK with a good toolset. Its like a 91mm Apprentice with an inline phillips and magnifying glass added and corkscrew on the backside instead of the phillips. I'm not a corkscrew fan nor do I need the small driver it can hold but I haven't seen any non backside tool scales for 91mm or I would drop those altogether.
Good luck with your mods!!
-
Titanium Tool 58mm
-
Pioneer with Scissors Burnt Bronze Cerakote. Titanium screws. Brass liners.
-
Nice one ALM

Sent from my SM-G920R4 using Tapatalk
-
I have one ALM custom and it is amazing!! Now the problem is the more of his work I see the more I want!
-
-
-
@hiraethus said:
Making some brass liners for Pioneers

I like the work pics.

-

I should have taken more, but only managed to snatch a bit of time in the evenings to make a start on these. The process is a bit laborious, but it's nice when they start to really take shape like this.
-
That's one thick liner right there! :o :D

-
:D It's 9 or 10 liners all stacked up so I can shape them in one go. TBH it's a bit thick for my belt sander and fret saw to handle - I'd be better off doing them 4 or 5 at a time.
-
Fret saw? You're cutting them manually?!
I'm both jealous and inspired. I'll mod me a SAK or three, one day

-
-
@firiki said:
Fret saw? You're cutting them manually?!I'm both jealous and inspired.

Yep, all manual - except for the belt sander.
The way I do it is:
Cut the blanks using tin snips (21 mm x 100 mm or so) out of 0.8 mm brass sheet.
Flatten the blanks as they get bent during cutting.
Drill and deburr one pivot hole in each blank.
Stack the liners and clamp together with a single factory liner as a drilling template, using a 3mm pin through the already drilled hole as location.
Drill the other two holes in the stack - this ensures that they're all in the same place.
Separate out the stack and deburr the holes as necessary
Rebuild the stack with a factory liner at each end to act as a guide for the sanding - bolt and rivet together tightly.
Hacksaw as much material from the outside as possible.
Use belt sander to get the outer edges close to the liners.
Use a combination of hack and fret saw to remove the material from the middle.
Belt sand the bits in the middle you can get to.
Keep going at the shaping with files until very close to the shape of the factory liners, then switch to aluminium oxide/silicon carbide paper and polish to finish.You really should.

-
Fret saw? You're cutting them manually?!
I'm both jealous and inspired. I'll mod me a SAK or three, one day

Yeah, a SAK of mass destruction
And I'll call it magentus' silence (at last)...
will it have a fish scaler?
Yes, it is useful in pic-nics and other occasions. It will be called magentus' sorrow

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

