Work in progress: display cabinet
-
Here's how the test escutcheon looks with the red enamel. I also had a try at cutting out the keyhole, with less than 100% success as you can see... it was a useful learning experience though, and I think it should be easier with the thicker brass that I'll use to make the real thing. Anyway I like the red and I think I'll go with it.

-
You could try with nail polish first to see how you like it*. I think red enamel would look splendid though brass has a yellow aspect and past certain proportions it doesn't match well with red, in my opinion. I assume the escutcheon will be placed in the middle of the door's cover?
Well red nail polish is not really my style :) but I did find a small pot of red enamel in the cupboard so I've put some on my test piece. It seems to be taking a long time to set though, could be the paint is bad as it's very old. Hopefully it will set well enough to allow me to sand it off the raised areas and get an impression of how it looks.
The position is fixed by the dimensions of the lock, which will put it quite close to the edge of the door (13mm from the edge to the centre of the keyhole).
I mentioned nail polish for two reasons, the first one was to save you money from buying enamel you might not use after all. The other reason (* :D
) was a couple of threads about nail polish on Alox SAKs.Anyway. I see you're going to make just the escutcheon as lock cover. I thought you'd be making it like the test piece, a square with the shield in it, in which case I'd go for plain brass and maybe add some etching for texture/reflection. The shield with enamel on looks tempting but only if it's quite small. :)
-
A little more progress: the striker plate for the lock installed, and cut out the keyhole.


-
Nice progress


-
Painting the back and inside panels with a light cream colour from my collection of old paint samplers...

-
I etched the thick brass sheet for the real lock escutcheon today, so thought I would share some info about the process.
Step 1 is to degrease the brass and then apply a resist to the areas that won't be etched. The method I'm using is toner transfer. You print the design on a laser printer, and transfer it to the brass using an iron. There are a number of variations on this idea. Using transparency film is one way I tried, but I had better results using glossy inkjet photo paper. After taping the design onto the brass, I applied the iron (set on max) first to the back of the brass for 20 seconds to preheat it, then turned it over (heat-proof gloves essential!) and ironed the paper onto the brass for about 10-15 seconds. Then I rubbed the paper down with a blunt instrument to make sure it's properly stuck. Finally you can soak the paper off in water, slowly rubbing it away in layers until you're left with just the toner stuck to the brass.
If there are any defects in the resist, supposedly you can patch them up with a permanent marker. I have to say I didn't find that to be completely effective. If you go too far with the marker then you can scrape it off again with a scalpel. And a SAK magnifier is handy to check the resist for defects :)
The second photo shows the setup for etching: protective equipment (gloves and eye protection); ferric chloride etchant; disposable plastic tray; a sponge; a bath of water to dunk the workpiece in when etching is finished; paper towels in case of any mess; bicarbonate of soda to neutralise the etchant before disposal; all on a trash bag to protect the work surface.
In the "sponge method" you use only a small amount of etchant, and gently wipe it over the surface so that the metal is continually exposed to fresh etchant. This method is faster than simple immersion. I etched for 10 minutes. When the desired degree of etching is achieved, rinse the piece in water to stop the reaction. Finally, clean off the resist with acetone.I must have got a bit lucky when I did the test piece, because my first go on the thick brass was not so good (top of 3rd picture). Top right was from a transparency print, which didn't transfer enough toner to the brass so the etch isn't very clearly defined. Top left was from glossy inkjet paper, and it's almost good except one little area where the etchant got under the toner. The second piece was much more successful - I rubbed it down harder after ironing, and took more time over soaking the paper off.



-
Excellent work. I have about zero carpentry skills, so this kind of craftsmanship always amazes me.
Sent from 9 miles from the face of the sun
-
Finished shaping the escutcheon for the keyhole. I made 2 in case I messed it up at any point. I will probably paint one of them and decide which to use when I've got the finish on the case.
It will be fixed with brass pins, which have to be short so as not to hit the lock body on the inside of the door. I didn't have any suitable so I cut down some longer ones. They actually turned out to be brass-plated steel, too tough for SAK pliers to cope with, but a Vic Spirit and a SOG PPP cut through them with ease.

-
@shibafu said:
Finished shaping the escutcheon for the keyhole. I made 2 in case I messed it up at any point. I will probably paint one of them and decide which to use when I've got the finish on the case.It will be fixed with brass pins, which have to be short so as not to hit the lock body on the inside of the door. I didn't have any suitable so I cut down some longer ones. They actually turned out to be brass-plated steel, too tough for SAK pliers to cope with, but a Vic Spirit and a SOG PPP cut through them with ease.
Wowzeer.. those look great

-
Great work shibafu
I reckon the cabinet is going to more of a talking point than the contents! -
I like how this is progressing very much.

This will look excellent and maybe you'll even get requests from other members for their collections. :D
-
Finished shaping the escutcheon for the keyhole. I made 2 in case I messed it up at any point. I will probably paint one of them and decide which to use when I've got the finish on the case.
It will be fixed with brass pins, which have to be short so as not to hit the lock body on the inside of the door. I didn't have any suitable so I cut down some longer ones. They actually turned out to be brass-plated steel, too tough for SAK pliers to cope with, but a Vic Spirit and a SOG PPP cut through them with ease.
Wowzeer.. those look great

+1 8)
-
Well it feels like we're in the home straight now as I've started applying the finish to the case. It's an antique pine tinted Danish oil. I'll probably give it 5 coats of oil on the visible areas, then let it cure for a week or so before applying a final coat of wax.

-
Absolutely astonishing, this place is such an inspiration. The love of craft and skill knows no bounds. Really just a work of art, congrats, really beautiful.
-
Thats some beautiful work, I just used some scrap wood cut and finished it for my small collection. The collection keeps growing, may have to do some more woodworking.
-
Nearly there now! The oil has cured, and I've waxed and buffed it. I've fitted the window (held in place by bead moulding nailed on the inside) and reassembled everything.
For the escutcheon I decided against the shiny brass with red enamel. It just didn't go with the antique pine finish. Dark, antique-looking brass fittings suit it better. The dark patina is achieved using a combination of brine and fuming with ammonia, with the following method. I did the hinges as well.
Quick method for darkening brass by ammonia fuming:
First prepare the brine: 2 tablespoons of salt in a cup of water.
And set up the fuming chamber. I used a tupperware-type box. Put some household ammonia in an open container inside the box.
Use soap or solvent to degrease the brass hardware.
Dip the brass in the salt water, then put it in the box (but not in the ammonia!) and seal it up.
It'll darken very quickly. After a few minutes, open the box, give it another bath in the brine, and return to the fuming chamber. After about 5 iterations of this process, it should be a solid, consistent black.
Then you can use wire wool to rub the patina back to get the desired degree of shininess.

-
Outstanding!

Looking forward to seeing it fully loaded.

-
Superb!

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
