Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Work in progress: display cabinet

Scheduled Pinned Locked Moved Swiss Army Knights Forum
88 Posts 1 Posters 7.4k Views
  1. Home
  2. Tool Talk
  3. Swiss Army Knights Forum
  4. Work in progress: display cabinet
Work in progress: display cabinet
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • shibafu Offline
    shibafu
    Posts: 604
    shibafu Offline
    shibafu
    wrote on last edited by
    #43 Quote Reply

      I also had an idea about my escutcheon vexation: I'm going to try making one. This is just a test piece using some thin brass that I had. I've got some thicker brass plate on order. The design is etched using ferric chloride. It's not perfect but I think the idea is sound.

      I'm contemplating whether I should fill in the etched area with some red enamel paint, or leave it as plain brass. Opinions?

      displaycab24.jpg

      1 Reply Last reply
      • AimlessWanderer Offline
        AimlessWanderer
        Posts: 17,518
        AimlessWanderer Offline
        AimlessWanderer
        wrote on last edited by
        #44 Quote Reply

          @shibafu said:
          I also had an idea about my escutcheon vexation: I'm going to try making one. This is just a test piece using some thin brass that I had. I've got some thicker brass plate on order. The design is etched using ferric chloride. It's not perfect but I think the idea is sound.

          I'm contemplating whether I should fill in the etched area with some red enamel paint, or leave it as plain brass. Opinions?

          I think red enamel would look excellent! :tu:

          The cantankerous but occasionally useful member, formally known as 50ft-trad

          1 Reply Last reply
          • nsa-x-file Offline
            nsa-x-file
            Posts: 1,270
            nsa-x-file Offline
            nsa-x-file
            wrote on last edited by
            #45 Quote Reply

              Really looking forward to seeing this completed. :popcorn:

              Merit Badges
              ALOX Colors Level 3 Photographer BO Tools Level 3 Flashlight Birth Year SAK
              1 Reply Last reply
              • firiki Offline
                firiki
                Posts: 6,076
                firiki Offline
                firiki
                wrote on last edited by
                #46 Quote Reply

                  @shibafu said:
                  I'm contemplating whether I should fill in the etched area with some red enamel paint, or leave it as plain brass. Opinions?

                  You could try with nail polish first to see how you like it*. I think red enamel would look splendid though brass has a yellow aspect and past certain proportions it doesn't match well with red, in my opinion. I assume the escutcheon will be placed in the middle of the door's cover?

                  • :D :whistle:

                  Omnia vincit amor. Vae victis.

                  1 Reply Last reply
                  • shibafu Offline
                    shibafu
                    Posts: 604
                    shibafu Offline
                    shibafu
                    wrote on last edited by
                    #47 Quote Reply

                      @firiki said:
                      You could try with nail polish first to see how you like it*. I think red enamel would look splendid though brass has a yellow aspect and past certain proportions it doesn't match well with red, in my opinion. I assume the escutcheon will be placed in the middle of the door's cover?

                      Well red nail polish is not really my style :) but I did find a small pot of red enamel in the cupboard so I've put some on my test piece. It seems to be taking a long time to set though, could be the paint is bad as it's very old. Hopefully it will set well enough to allow me to sand it off the raised areas and get an impression of how it looks.

                      The position is fixed by the dimensions of the lock, which will put it quite close to the edge of the door (13mm from the edge to the centre of the keyhole).

                      1 Reply Last reply
                      • shibafu Offline
                        shibafu
                        Posts: 604
                        shibafu Offline
                        shibafu
                        wrote on last edited by
                        #48 Quote Reply

                          This and the next post are yesterday's work. First the last couple of routing operations on the door. A chamfer detail around the inside edge on the front, and a rebate to receive the window on the back.

                          displaycab25.jpg

                          displaycab26.jpg

                          1 Reply Last reply
                          • shibafu Offline
                            shibafu
                            Posts: 604
                            shibafu Offline
                            shibafu
                            wrote on last edited by
                            #49 Quote Reply

                              This piece of 1/2" plywood will form the back panel, and the side shelf supports. I've routed 1/8" grooves across it that the shelves will slot into.

                              The plywood has been in the garage for a while and has grown a bit of mould. Not a problem though. I treated it with some fungicide to kill the mould, and the stain will be covered by paint.

                              displaycab27.jpg

                              displaycab28.jpg

                              1 Reply Last reply
                              • shibafu Offline
                                shibafu
                                Posts: 604
                                shibafu Offline
                                shibafu
                                wrote on last edited by
                                #50 Quote Reply

                                  The panel cut apart to form the side and back pieces. The second photo shows how they'll fit in the case.

                                  displaycab29.jpg

                                  displaycab30.jpg

                                  1 Reply Last reply
                                  • shibafu Offline
                                    shibafu
                                    Posts: 604
                                    shibafu Offline
                                    shibafu
                                    wrote on last edited by shibafu
                                    #51 Quote Reply

                                      Here's how the test escutcheon looks with the red enamel. I also had a try at cutting out the keyhole, with less than 100% success as you can see... it was a useful learning experience though, and I think it should be easier with the thicker brass that I'll use to make the real thing. Anyway I like the red and I think I'll go with it.

                                      displaycab31.jpg

                                      1 Reply Last reply
                                      • firiki Offline
                                        firiki
                                        Posts: 6,076
                                        firiki Offline
                                        firiki
                                        wrote on last edited by
                                        #52 Quote Reply

                                          @shibafu said:

                                          @firiki said:

                                          You could try with nail polish first to see how you like it*. I think red enamel would look splendid though brass has a yellow aspect and past certain proportions it doesn't match well with red, in my opinion. I assume the escutcheon will be placed in the middle of the door's cover?

                                          Well red nail polish is not really my style :) but I did find a small pot of red enamel in the cupboard so I've put some on my test piece. It seems to be taking a long time to set though, could be the paint is bad as it's very old. Hopefully it will set well enough to allow me to sand it off the raised areas and get an impression of how it looks.

                                          The position is fixed by the dimensions of the lock, which will put it quite close to the edge of the door (13mm from the edge to the centre of the keyhole).

                                          I mentioned nail polish for two reasons, the first one was to save you money from buying enamel you might not use after all. The other reason (* :D :whistle:) was a couple of threads about nail polish on Alox SAKs.

                                          Anyway. I see you're going to make just the escutcheon as lock cover. I thought you'd be making it like the test piece, a square with the shield in it, in which case I'd go for plain brass and maybe add some etching for texture/reflection. The shield with enamel on looks tempting but only if it's quite small. :)

                                          Omnia vincit amor. Vae victis.

                                          1 Reply Last reply
                                          • shibafu Offline
                                            shibafu
                                            Posts: 604
                                            shibafu Offline
                                            shibafu
                                            wrote on last edited by
                                            #53 Quote Reply

                                              A little more progress: the striker plate for the lock installed, and cut out the keyhole.

                                              displaycab32.jpg

                                              displaycab33.jpg

                                              1 Reply Last reply
                                              • Caranthanus Offline
                                                Caranthanus
                                                Posts: 1,775
                                                Caranthanus Offline
                                                Caranthanus
                                                wrote on last edited by
                                                #54 Quote Reply

                                                  Nice progress :2tu:

                                                  :popcorn:

                                                  1 Reply Last reply
                                                  • shibafu Offline
                                                    shibafu
                                                    Posts: 604
                                                    shibafu Offline
                                                    shibafu
                                                    wrote on last edited by
                                                    #55 Quote Reply

                                                      Painting the back and inside panels with a light cream colour from my collection of old paint samplers...

                                                      displaycab34.jpg

                                                      1 Reply Last reply
                                                      • shibafu Offline
                                                        shibafu
                                                        Posts: 604
                                                        shibafu Offline
                                                        shibafu
                                                        wrote on last edited by shibafu
                                                        #56 Quote Reply

                                                          I etched the thick brass sheet for the real lock escutcheon today, so thought I would share some info about the process.

                                                          Step 1 is to degrease the brass and then apply a resist to the areas that won't be etched. The method I'm using is toner transfer. You print the design on a laser printer, and transfer it to the brass using an iron. There are a number of variations on this idea. Using transparency film is one way I tried, but I had better results using glossy inkjet photo paper. After taping the design onto the brass, I applied the iron (set on max) first to the back of the brass for 20 seconds to preheat it, then turned it over (heat-proof gloves essential!) and ironed the paper onto the brass for about 10-15 seconds. Then I rubbed the paper down with a blunt instrument to make sure it's properly stuck. Finally you can soak the paper off in water, slowly rubbing it away in layers until you're left with just the toner stuck to the brass.

                                                          If there are any defects in the resist, supposedly you can patch them up with a permanent marker. I have to say I didn't find that to be completely effective. If you go too far with the marker then you can scrape it off again with a scalpel. And a SAK magnifier is handy to check the resist for defects :)

                                                          The second photo shows the setup for etching: protective equipment (gloves and eye protection); ferric chloride etchant; disposable plastic tray; a sponge; a bath of water to dunk the workpiece in when etching is finished; paper towels in case of any mess; bicarbonate of soda to neutralise the etchant before disposal; all on a trash bag to protect the work surface.
                                                          In the "sponge method" you use only a small amount of etchant, and gently wipe it over the surface so that the metal is continually exposed to fresh etchant. This method is faster than simple immersion. I etched for 10 minutes. When the desired degree of etching is achieved, rinse the piece in water to stop the reaction. Finally, clean off the resist with acetone.

                                                          I must have got a bit lucky when I did the test piece, because my first go on the thick brass was not so good (top of 3rd picture). Top right was from a transparency print, which didn't transfer enough toner to the brass so the etch isn't very clearly defined. Top left was from glossy inkjet paper, and it's almost good except one little area where the etchant got under the toner. The second piece was much more successful - I rubbed it down harder after ironing, and took more time over soaking the paper off.

                                                          displaycab35.jpg

                                                          displaycab36.jpg

                                                          displaycab37.jpg

                                                          1 Reply Last reply
                                                          • BASguy Offline
                                                            BASguy
                                                            Posts: 935
                                                            BASguy Offline
                                                            BASguy
                                                            wrote on last edited by
                                                            #57 Quote Reply

                                                              Excellent work. I have about zero carpentry skills, so this kind of craftsmanship always amazes me.

                                                              Sent from 9 miles from the face of the sun

                                                              1 Reply Last reply
                                                              • Caranthanus Offline
                                                                Caranthanus
                                                                Posts: 1,775
                                                                Caranthanus Offline
                                                                Caranthanus
                                                                wrote on last edited by
                                                                #58 Quote Reply

                                                                  @BASguy said:
                                                                  Excellent work.

                                                                  1+ :tu:

                                                                  :popcorn:

                                                                  1 Reply Last reply
                                                                  • shibafu Offline
                                                                    shibafu
                                                                    Posts: 604
                                                                    shibafu Offline
                                                                    shibafu
                                                                    wrote on last edited by shibafu
                                                                    #59 Quote Reply

                                                                      Finished shaping the escutcheon for the keyhole. I made 2 in case I messed it up at any point. I will probably paint one of them and decide which to use when I've got the finish on the case.

                                                                      It will be fixed with brass pins, which have to be short so as not to hit the lock body on the inside of the door. I didn't have any suitable so I cut down some longer ones. They actually turned out to be brass-plated steel, too tough for SAK pliers to cope with, but a Vic Spirit and a SOG PPP cut through them with ease.

                                                                      displaycab38.jpg

                                                                      1 Reply Last reply
                                                                      • Etherealicer Offline
                                                                        Etherealicer
                                                                        Admin Team
                                                                        Posts: 12,034
                                                                        Etherealicer Offline
                                                                        Etherealicer
                                                                        Admin Team
                                                                        wrote on last edited by
                                                                        #60 Quote Reply

                                                                          @shibafu said:
                                                                          Finished shaping the escutcheon for the keyhole. I made 2 in case I messed it up at any point. I will probably paint one of them and decide which to use when I've got the finish on the case.

                                                                          It will be fixed with brass pins, which have to be short so as not to hit the lock body on the inside of the door. I didn't have any suitable so I cut down some longer ones. They actually turned out to be brass-plated steel, too tough for SAK pliers to cope with, but a Vic Spirit and a SOG PPP cut through them with ease.

                                                                          Wowzeer.. those look great :tu:

                                                                          It wouldn't be the internet without people complaining.

                                                                          1 Reply Last reply
                                                                          • magentus Offline
                                                                            magentus
                                                                            Admin Team
                                                                            Posts: 21,659
                                                                            magentus Offline
                                                                            magentus
                                                                            Admin Team
                                                                            wrote on last edited by
                                                                            #61 Quote Reply

                                                                              Great work shibafu :salute: I reckon the cabinet is going to more of a talking point than the contents!

                                                                              'Use the force Harry' - Gandalf

                                                                              Merit Badges
                                                                              Hacker Hook User Duct Tape Hobo User Minimal SAK Challenge Ignore SAKMC Santa
                                                                              1 Reply Last reply
                                                                              • enki_ck Offline
                                                                                enki_ck
                                                                                Global Moderators
                                                                                Posts: 20,936
                                                                                enki_ck Offline
                                                                                enki_ck
                                                                                Global Moderators
                                                                                wrote on last edited by
                                                                                #62 Quote Reply

                                                                                  I like how this is progressing very much. :hatsoff:

                                                                                  This will look excellent and maybe you'll even get requests from other members for their collections. :D

                                                                                  <a href="https://forum.multitool.org/index.php/topic,63583.msg1195187.html#msg1195187">[b]How to do SAKwiki edits[b]</a>

                                                                                  Merit Badges
                                                                                  Juice Collector Level 1 Mod User Hacker Scale Changer EDCSource Buyer Multitool Encyclopedia User OCD Squad SAKWiki User Flashlight Time Lord Level 3
                                                                                  1 Reply Last reply

                                                                                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                                                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                                                  With your input, this post could be even better 💗

                                                                                  Register Login

                                                                                  • 1
                                                                                  • 2
                                                                                  • 3
                                                                                  • 4
                                                                                  • 5
                                                                                  1. Home
                                                                                  2. Tool Talk
                                                                                  3. Swiss Army Knights Forum
                                                                                  4. Work in progress: display cabinet
                                                                                  Reply
                                                                                  • Reply as topic
                                                                                  Log in to reply
                                                                                  COMMUNITY LINKS
                                                                                  EDC-TV SAKWiki GearFeed SAKSelector
                                                                                  Operational Funds

                                                                                  Help us keep the Unworkable working!

                                                                                  Make A Donation
                                                                                  November Goal: $300.00
                                                                                  Due Date: Nov 30
                                                                                  Total Receipts: $0.00
                                                                                  Below Goal: $300.00
                                                                                  0% funded
                                                                                  • Login

                                                                                  • Don't have an account? Register

                                                                                  • Login or register to search.
                                                                                  • First post
                                                                                    Last post
                                                                                  0