I mod everything
-
@Flint Hills said:
I would guess that those are made of aluminum. Aluminum won't turn dark with acid etching, it will eat away a small amount of the surface.Interesting that the truck bed liner didn't work on it. What else have you used that stuff on?
The clasps are definetely Stainless steel, not aluminium.
-
Stainless steel and rostfri are hard to get anything stay on their surface. Paint usually just chips away, chemicals hardly do anything to them. But you might want to try fire on them. Specially very different degrees from candle flame to blowtorch. Then dipping in alcohol might give different solution compared to dipping in oil.
-
Some other things I've done. Zebra shorties and a stylus shortie

This one for size reference

-
Would you mind going in detail on how to shorten a pen like that?

-
@lowtech said:
Would you mind going in detail on how to shorten a pen like that?
Not at all. I don't mind
It actually very easy.
Take the whole thing apart to start.
Screw the tip back on slightly to push the plastic insert out of the pen.
Figure out how short you want it.
Cut the middle of the plastic insert in half, then remove equal amounts from both sides.
Example: if you want it one inch shorter remove 1/2 from each side, that is important.
Then cut the top of the steel sleeve off the same amount. Do not cut the part where the tip is!
Push the threaded plastic end (tip) all the way in and thread the tip back on.
Then insert the top part. You can glue or weld the 2 pieces of plastic together before hand if you can. I used a solder iron to melt it together.
The trick is to cut the pen refill off the same way. Reinstall everything and there you go.
I have some spare parts in my shop and I will try to get some pics. -
That World bei nice! Although i don't real need yet another modding Addition beides bikes, tools, watches, packst . . .
-
Here's some pics.


The tip as described is the knurled portion and the smaller end on the plastic. The reason we must save these is that there is threaded portion in these parts.
-
@lowtech said:
That World bei nice! Although i don't real need yet another modding Addition beides bikes, tools, watches, packst . . .I could make you a set if you want some. Just finding the pen is the fun part. I have also done this to the pencil which is actually in the photo (the black one,who knew)
-
Very cool mods on those pens and pencils! The Zebra f701 is my favorite. I need to make a matching pencil for mine. I've done the mod to swap the click mechanism and clip from a f402, gives it a cleaner look and makes it all metal (at least the outside). I've had the Fisher Space pen refills in them but now I have fit a Zebra g301 gel refill in and love that.
-
I shure would like a set, but I don´t want to produce any stress on your side. Might you be interested in a trade of any kind maybe?
-
I guess I´ll have to wait and see... :D
-
Update to the watch clasp. The black epoxy paint with clear lacquer over top is holding up extremely well. I'll get pics soon. So far it's been on a week and while working and it's hasn't came off yet.
-
After this its on to the watch case. I plan on darkening this piece

I have 2 cases just in case it breaks or doesn't work.
-
And another slim juice is born. This one has a new scale material.

-
@tattoosteve99 said:
After this its on to the watch case. I plan on darkening this piece
I have 2 cases just in case it breaks or doesn't work.
I have no firsthand experience with the GW-7900 myself, but from other models I own(ed) I am quite sure the plastic faceplate can only be taken out when you press out thw crystal. Tjhis was easier on old G-Shocks where you could just take it out to the back without touching the crystal. Be careful not to break it or the solar cell beyond it. I guess it would be the best to make a well fitting wooden stamp to ensure equal pressure on most of the exposed crystal from the inside. Maybe it would be an option to remove one pusher and replace teh caseback and then press teh crystal out with compressed air?! Put everything inside some layers of a soft cloth when attempting this so you don´t get teh crystal out unharmed only to shatter it on the next wall...
I´m looking forward to the outcome and hope it works out! -
Well I can say first hand it doesn't come out that way. I broke the crystal in the watch while welding. Then I replaced it. The little white plastic piece comes out on its own after you remove the buttons. It is a pain to do it. I just havent had time yet.
-
Another thing learned! Thanks. I thought they would use the same fixture methods on more models, but it seems it varies from model to model. If it makes you less nervous to now there is a spare, I can provide one or two spare circlips (those little ones holding the buttons and going airborne all too happily).
-
This is after 2 weeks on the wrist. No signs of wear as of yet.


The shiny parts are just glare.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

