Sharpening with Paper Wheels
-
Spyderco Southard with CTS-204P blade, which has been in use for a few years now with a Dutch scout leader.
It has already been sharpened several times by him on stones, plus two times by me on Paper Wheels (once up to 6 micron diamond compound, and once up to 15 micron diamond, the latter performing noticeably longer for the owner)This time the knife was reprofiled from about 30 degrees inclusive to 25 degrees inclusive with a standard Paper Wheel with 220 grit SiC, then deburred with a second Paper Wheel with 0.25 micron diamond compound.
This produces a polished semi-coarse edge with an aggressive bite, as the knife is going to be used to cut a lot of 10 mm polyprop rope in the coming weeks.
You can click the pics 2 x for a bit more detail. -
A Strider SMF with S110V blade from a Dutch forum member.
According to my Tormek angle gauge the old edge measured +/- 40 degrees inclusive from the heel to half an inch before the tip where it changed into 45 degrees inclusive.
The owner uses this knife mostly to cut various kinds of green wood & twigs in horticulture, and had already tried his hand at reprofiling the edge himself with a DMT Diafold.
Together we came to the conclusion that the edge could do with a full reprofiling, as well as with a finer edge finish to better suit his specific purposes.
BTW: the owner also contacted Duane Dwyer by mail, among other things to ask him about the hardness of this S110V blade, and according to Duane it measures 61 HRC.This was the knife before sharpening:
After reprofiling & sharpening.
The new edge angle came out at +/- 32 degrees inclusive along the entire edge, and it can treetop armhair and slice single ply toilet paper.
Probably due to having the flu at the moment my hands didn't do exactly what i wanted them to do, and as a result i didn't manage to get both bevels completely symmetrical.
Grit progression: a Paper Wheel with 220 grit SiC for reprofiling, a second Paper Wheel with 15 micron diamond compound for refining, and a third Paper Wheel with 0.25 micron diamond compound for removing the tiny burr. -
The factory edge of this Spyderco PM2 in S110V steel was barely shaving armhair on skinlevel, and according to my Tormek WM200 the edge angle was near 35 degrees inclusive.
The old apex was removed by cutting several times straight into a silicon carbide stone, and then i used 4 different Paper Wheels coated with diamond compounds (15, 6, 3, and 1 micron) to create & refine the new edge.
Normally i don't take high carbide steel types this far, but in this case i wanted to see how the S110V steel would do.The new & ever so slightly convex edge measures a hair below 30 degrees inclusive, and can easily whittle a normal chest hair towards the point along the entire edge.
Thinner ones will sever immediately upon touching.
My cheap camera is not really able to show full details, but at least it gives some impression. -
-
Robert,
Whenever I see a thread about sharpening, I'm delighted to see you are the author of it.
I always enjoy seeing your superb work on various blades. You're very skilled! :D
Thanks for taking the time to share buddy


-
I've been dreaming over the S110V PM2 but now I want one that's been sharpened by you.

-
Happy Holidays
I recently purchased a Razor Sharp Paper Wheel system and I am concerned that sharping blades several times will start to take too much metal off. I have used a Spyder Co Tri Angle for years with good success on carbon steel blades, but S30v and harder takes forever and does not have the "Super Scary Sharp" results. I have quite a collection of folders/fixed knives and most in my collection are for show only. My dozen or so of every day and hunting knives are always kept sharp and with the Tri Angle there is very little metal removed with sharping.
Could you use 220 or a finer grit instead of the 180 that comes with the wheels and would it be effective?
I have read the information from kwakster and saw the pictures and he surely has the gift to put a scary sharp edge on a knife blade. I think the wheel system would be good to get an edge on a hard to sharpen blade and then minor touch ups with the Tri Angle. Nothing bothers me more that blade that is not sharper than a razor.
Thanks
Lenbo -
The slotted wheel with compound makes for a very quick touch-up with minimal metal removal. No need to waste time with other methods. There is absolutely no need to use the grit wheel every time. Do you start your stone sharpening on the coarse stone when you just wish to touch-up a blade? Why would you on the wheels?
The 180 grit is used to cut quickly, allowing one to develop a burr rapidly with minimal heat buildup. A finer grit would require more time and result in greater heat buildup. The amount of metal that needs to be removed to create a burr does not change, regardless of the sharpening method. Your skill is the determining factor.
Don't over think this...
-
@Lenbo: regarding sharpening knives in S30V and other high vanadium carbide steels:
*To get the most out of high vanadium carbide steels you need abrasives that are able to cut & shape the carbides themselves, which in commonly available materials leaves only CBN and diamond.
For both maximum sharpness & edge retention you want a row of actually shaped & sharpened carbides in your edge, not just a row of whole carbides (which will do for coarser edge types, but they simply work better when sharp.)Other abrasive media like chromium oxide, aluminum oxide and silicon carbide will most certainly plough through the matrix and push the vanadium carbides out of the way, but due to their lack in hardness they are physically unable to refine those carbides.
Take a look at the bottom of this page for a list of materials and their Knoop hardness:
Electron Microscopy, Light Microscopy, Instruments and Supplies, Ted Pella, Inc.
electron microscopy supplies and instruments, light microscopy, atomic force microscopy, laboratory supplies
(www.tedpella.com)
What works for me when i want a (semi-) coarse edge on S110V steel and the like is to use silicon carbide (220 grit Paper Wheel and/or 1000 grit Tormek Blackstone) to create the bevels, then jump to a fine diamond compound (1 micron on a Paper Wheel) to remove the burr.
This provides me with the edge irregularities (or teeth if you want) for that coveted slicing aggression, and which also have actual sharpened vanadium carbides in the apex.
For a more polished edge on S110V steel and the like i refine the results of the silicon carbide with various diamond compounds (in my case 15, 6, 3, and 1 micron on dedicated Paper Wheels)For some time now i've also been experimenting with a Rubber Wheel coated with 230 grit diamond as a substitute for the 220 grit silicon carbide grit Paper Wheel, and although i still need to learn more about it, so far i like the results i'm getting with it.*
-
16VTGIDAVE and KWAKSTER
Thanks a million for you quick response and information. I figured that after using the gtrit wheel the slotted wheel could be used for touch ups. I saw a utube really knocking the wheel system and how it just grinds the blade down, but figured that they were over using it.
I Re-dressed my paper wheel by doing what KAWAKSETER did in his thread July 09,2014 and probably didn't do it correct because it didn't seem to work. Tried sharping a Benchmade 154CM folder and could not even get a burr (probably too much glue). By the way my father in law could never get an edge on this 154cm blade before. I figured I would try the "Wheel".
I just went back and redressed the grit wheel again with only one layer of glue and grit. Will wait for it to dry and start over. I imagine that there is a learning curve with this system and free hand on the wheels. I just need to practice for the results I hope to achieve. When I get a little more experienced with this system I would like to try the diamond compounds.
Thanks much
LenBo -
The Manix 2 lightweight in S110V is a superb knife, and it exemplifies Spyderco's motto "simplify and add lightness".
The model only seems to have two possible disadvantages: it takes up quite a bit of real estate in your pocket, and some people can't seem to get over the fact that it has an ultra lightweight plastic handle, which to them makes the knife feel cheap and not worth the asking price.
But after providing them with some links to real life tests with this knife some of them change their minds :-)I do hope however that the factory edges get some more attention in the future, as i already had to resharpen 5 pcs of this model that couldn't even slice copy paper.
Upon inspection all these edges had visible burr remains and edge angles measured around 35 degrees inclusive.This is one of them with it's new bling & bite edge, as i call them: reprofiled to +/- 30 degrees inclusive with 230 grit diamond powder on a Rubber Wheel, refined with 15 micron diamond compound on a Paper Wheel, and deburred with 0,25 micron diamond compound on a second Paper Wheel.
To me the shiny bevels are actually a side effect, as it's the clean cutting of the large amount of vanadium carbides that i'm after. -
This second hand Spyderco Military in CPM-D2 steel was one of the first knives i ever sharpened on my standard set of Paper Wheels back in 2009.
It had some blade play (fixed it), some discoloration on the blade (left that) and it wasn't quite sharp (fixed that with the Wheels)
Was part of my edc for several years.









-
Kwakster you are an extremist.
I've always said,"you can learn from an extremist".LOL
Thanks for sharing all of this information.
-
Well, that depends on your point of view, :D
Sharing info is what forums are all about, and useful tools with a great price to performance ratio like these Paper Wheels deserve to be introduced to a larger audience.
-
Did these chisel ground edges a a few years ago with a Paper Wheel coated with 15 micron diamond compound, and then stropped the burr on the other side off on hard leather with some 1 micron diamond compound.
Both knives were quite blunt, one even more than the other.
The knives are owned by two Dutch Special Forces guys who used & sharpened them while on tour in Afghanistan, and they wanted the new edges to have a little bling. -
Below you see 3 different viewing angles of the edge i recently put on a brand new Sebenza 25 (which had a subpar factory edge)
The owner of the knife took the pictures with a very expensive Leica camera to capture the different looks this edge type can have when seen from different angles.
For obvious reasons i named this a bling & bite finish, and it performs very well on especially high (vanadium) carbide steels.I first reprofiled the factory edge from 35 degrees inclusive to 30 degrees inclusive with a Rubber Wheel coated with 230 grit diamond powder, then refined it with a Paper Wheel coated with 15 micron diamond compound, and lastly removed the tiny burr with a second Paper Wheel coated with 0.25 micron diamond compound.
The new and ever so slightly convex edge could treetop the hair on the back of my hand (even whittle it a bit) and easily slice single ply toilet paper.
And this was after i tested the edge with a few firm cuts into the edge of a piece of laminated desktop.


-
-
Awesome Kwakster
Can't wait to see those results :o
-
@ Poncho65: when i have some results with those Wheels i will post them here as well, :)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login









































