jlwatso1's 31 Day SOG Super Power Badge Quest
-
I don't know if yours is different, but on my unmodified powerlock the knife blade and scissors are in the grip with the lettering.
-
Used the needle nose to ream/woller out some copper and allow me to insert a copper line before braising. I like that it is more rounded than the head on Leatherman Surge. Haveing second thoughts about the nose job performed on my Surge. Forgot I used it for this. Oh yah, as I was reaming copper out, the other comfort grip/ tool cover slid up and was subsequently removed.
It's nice to see someone using their tool, mine's been doing minimal work these last couple of days. But how are those covers attached? They seem to come loose all the time!
There are just some notches in the tool. I think I would have to pop rivet them on if I wanted to keep them on a rough as I am on this thing...
-
i had similar issues with my Powerlock. I just tossed the handle covers, they were more annoying than they were worth.
-
@sLaughterMed said:
i had similar issues with my Powerlock. I just tossed the handle covers, they were more annoying than they were worth.Same here!

-
So it looks like it is going to be a long month... I was looking at my Powerlock and saw that the clip/retainer is missing from the bit adapter! The only time I have used it was to see if some bits from my socket set would work on it to replace my car battery a couple days ago, but I didn't have the right adapter. Guess it must have come off then. I will send it in for warranty after the challenge is over.

-
Here's a pic

-
Just call them up. They should send you one.
-
Also, nice action shots!
-
@ducttapetech said:
Just call them up. They should send you one.Sweet! I'll have to try that today! It's my off day.
-
DAY 4
Not much to report today. Tuesdays are my day off. Sent an email to SOG's warranty department this morning to see if they could send me a new 1/4" bit driver or if I would have to send it in. No reply ret. Fabricated a new tool lock for my PT-540. Got it functional, but it still needs some cosmetic work. I may stamp my initials in it with some letter punches my folks got me for Christmas. Had to stop working on it because my daughter just woke up from her nap. Hopefully I will be able to duplicate it so they both look the same. Pics are on the Leatherman forum under Surge/ES4 Possible mod question. If anyone is interested.
-
Just realized yesterday was DAY 5
-
DAY 6
Mostly did a lot of screen watching today while running tests on the ducted VRF system I cut copper for on Monday. Also had to do a little troubleshooting. Had to replace a burnt up contactor. Deadmun just helped tear a seal off of a drum of R-404A so I could add charge to a DX on the outdoor room of the psycrometric chamber. Not too exciting.


-
DAY 7
Started out the day using the scissors on my Powerlock to cut some socks/wicks for the wet bulb readings on our sample boxes. They seemed to work ok, but I wish they would lock in place. They did have a hard time cutting a medium sized zip tie. Used the pliers to tighten up a sanitary water fitting.




-
I have to force the lock into the notch in the scissors to get them to lock, a two hand operation, but they lock.

-
Hmmm... I tried that before and thought the screwdriver/bottle opener was just making it not lock because it doesn't have a stop so it doesn't rest where it needs to, but I just pressed really hard on the lock and you are right! It finally snapped in. Almost like the gap is to small for the lock to fit all the way. Thanks!

-
@jlwatso1 said:
Hmmm... I tried that before and thought the screwdriver/bottle opener was just making it not lock because it doesn't have a stop so it doesn't rest where it needs to, but I just pressed really hard on the lock and you are right! It finally snapped in. Almost like the gap is to small for the lock to fit all the way. Thanks!
Mine has similar problems, but it is completly the fault of the bottle opener and knife closing too far into the tool.
-
DAY 8
Note to self: SOG Powerlock has extremely sharp knife.

Whilst cutting through a large zip tie/panduit strap, some how I sliced through the nail and part of my left pinky finger... I would take pics, the superglue makes it look worse than it is. I think any way...
On a lighter note, SOG warranty got back with me and are sending new 1/4" drive spring.
-
I hope you cleaned that real well so you don't get an infection. Is your tetanus shot up to date? :ahhh
-
@Alan K. said:
I hope you cleaned that real well so you don't get an infection. Is your tetanus shot up to date? :ahhhYah I cleaned it out good and I'm up to date. If I would have cut it on something rusty I would have gone to the ER and gotten a shot, but I don't even think I've used this blade yet. I would rather avoid having to deal with worker's comp. if possible. It took me over year to get everything settled when I pulled a muscle in my back at another company.... Hospital kept calling me for the rest of the money they felt they were owed. It was a nightmare. If this had been worse I would have gone, but I think I'm good. Thanks for the concern though. I appreciate it.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login