jlwatso1's 31 Day SOG Super Power Badge Quest
-
@jlwatso1 said:
Hmmm... I tried that before and thought the screwdriver/bottle opener was just making it not lock because it doesn't have a stop so it doesn't rest where it needs to, but I just pressed really hard on the lock and you are right! It finally snapped in. Almost like the gap is to small for the lock to fit all the way. Thanks!
Mine has similar problems, but it is completly the fault of the bottle opener and knife closing too far into the tool.
-
DAY 8
Note to self: SOG Powerlock has extremely sharp knife.

Whilst cutting through a large zip tie/panduit strap, some how I sliced through the nail and part of my left pinky finger... I would take pics, the superglue makes it look worse than it is. I think any way...
On a lighter note, SOG warranty got back with me and are sending new 1/4" drive spring.
-
I hope you cleaned that real well so you don't get an infection. Is your tetanus shot up to date? :ahhh
-
@Alan K. said:
I hope you cleaned that real well so you don't get an infection. Is your tetanus shot up to date? :ahhhYah I cleaned it out good and I'm up to date. If I would have cut it on something rusty I would have gone to the ER and gotten a shot, but I don't even think I've used this blade yet. I would rather avoid having to deal with worker's comp. if possible. It took me over year to get everything settled when I pulled a muscle in my back at another company.... Hospital kept calling me for the rest of the money they felt they were owed. It was a nightmare. If this had been worse I would have gone, but I think I'm good. Thanks for the concern though. I appreciate it.
-
DAY 9
Deadmon's task for the day. A step stool came for my little girl. Not too challenging, but he was up to the task.




-
Nice! We've got that stool as well. My 2 y.o. loves it - she drags it around the house, periodically stopping to climb and/or sit on it for a couple minutes before dragging it elsewhere.
-
@rdub934 said:
Nice! We've got that stool as well. My 2 y.o. loves it - she drags it around the house, periodically stopping to climb and/or sit on it for a couple minutes before dragging it elsewhere.Lol, mine is 21 months. We got it so she could sit on the potty... My wife gives her an M&M when she try's. I think she just has figured out she gets an M&M, but I guess if it gets her to try it can't hurt. :D
-
Nice! We've got that stool as well. My 2 y.o. loves it - she drags it around the house, periodically stopping to climb and/or sit on it for a couple minutes before dragging it elsewhere.
Lol, mine is 21 months. We got it so she could sit on the potty... My wife gives her an M&M when she try's. I think she just has figured out she gets an M&M, but I guess if it gets her to try it can't hurt. :D
Yea, that was the intended purpose for ours as well. And we are using the same technique on our daughter (and it worked on Thing 1 and Thing 2 so why not 3 for 3, right?) Get an M&M every time they void, get two every time they move their bowels. Thing 3 is to the point where every time she farts on the potty she sticks her hand out

-
Nice! We've got that stool as well. My 2 y.o. loves it - she drags it around the house, periodically stopping to climb and/or sit on it for a couple minutes before dragging it elsewhere.
Lol, mine is 21 months. We got it so she could sit on the potty... My wife gives her an M&M when she try's. I think she just has figured out she gets an M&M, but I guess if it gets her to try it can't hurt. :D
Yea, that was the intended purpose for ours as well. And we are using the same technique on our daughter (and it worked on Thing 1 and Thing 2 so why not 3 for 3, right?) Get an M&M every time they void, get two every time they move their bowels. Thing 3 is to the point where every time she farts on the potty she sticks her hand out

😂
Nice! We aren't quite there yet... -
"Thing 3 is to the point where every time she farts on the potty she sticks her hand out "
- jlwatso1
Whoa, I just now realized that somebody owes me a whole bunch of M&Ms.
-
DAY 10
Nothing to report today. Just pocket carried my Powerlock to church again. I cleaned up my finger some yesterday. Took off the super glue and cleaned it out with hydrogen peroxide, then alcohol, and finally some neosporin antibiotic ointment. I leaned it out again later and then glued it shut again. Or rather I held it together and made my wife glue it shut. :D Here's some pics.



-
DAY 11
Wired in the communication wires and high voltage on a Air to Water VRF system today. Then piped in the water. Took a while because there were 3 outdoor units to pipe water to. Snapped a few action pics. I have noticed some play in the Phillips screwdriver. I have also noticed that it is almost impossible not to hit the tool lock and dissengauge the screwdriver while using it. Every time I pulled the knife out today, the medium screwdriver/bottle opener came out also. The tools just seem so close together.



-
Couple more pics.


-
DAY 12
Off day. Having a little coffee and catching up on some reading before my little one gets up. Might have to work on the tool locks for my PT-540 some more today while she naps.

-
DAY 13
Spent pretty much the whole day screen watching and trying to get the inlet water temperature down to 62 degrees F. Used my Powerlock to cut socks for the wet bulb readings. I also used my "calibrated tool" to adjust water flow rates to each of the 3 outdoor units. A tap here and a tap there...
The client's unit kept shutting off and screwing the water temp up so once their ibis came back on line, everything had to cycle. We finally had to have the 35 ton chamber shut down, because the 100 ton chiller we were using to cool the water in our tank didn't have enough capacity to run the 30 ton VRF and the 35 ton room at the same time.
I know the math doesn't work out... The chiller is a piece!
-
Before anybody goes trying to find Waldo in the picture... The Powerlock didn't make it in. :D

-
DAY 14
Worked on another air to water VRF setup today. Snapped a couple of pictures while using my Powerlock. Tried using the Phillips with the pliers opened to avoid hitting the tool locks as other MTO addicts have mentioned trying. This method worked pretty good. I also tried using the Phillips with the pliers opened at a 90 degree angle to help get some more torque. The last pick is of Dedmun hanging out in between helping me cut to finish insulating copper lines. Sorry I can't share pics of a full VRF setup due to confidentiality agreements. Oh yah, used wire strippers on PL to cut a small piece of t-stat wire to jump out the flow switch on the clients equipment. Almost forgot, I used the scissors ran into some issues. They were medium zip tires at most. And the scissors had a bit of a hard time cutting the zip tie. They also kind of hurt my fingers. I also used them on some TC wire to cut the ends off after twisting them together.



-
DAY 15
Well... This challenge is half way over and while I can't say that I'm not going through withdrawals from not carrying my Surge, I can say that the Powerlock has proven itself to be a very useful multitool. I also think when I deside to carry my PT-540 I will be more comfortable.
Today I used it to woller out some copper so I could fit the end of the swedging tool in to make a joint to extend the line set. I also used it to cut the straps to unbox the cassettes for the next ductless VRF setup. Normally, I would use the outside opening knife, but since the Powerlock is lacking in that department, I used the cutters on the plier head. First I kept the strap flat and it took 2 cuts. Then I folded it it two and was able to cut it in one cut.
Thoughts on the Powerlock
I haven't tried out the saw yet, but it looks mean. The scissors are lacking and dig into your fingers. As mentioned before they are hard to lock in place. Some of the tools feel wobbly, I may have to tighten the screw. I really have no need for a can opener or bottle opener but the extra screwdrivers are nice. Perhaps I might use the Dremel to cut the can opener down into a longer small flat head. The Phillips is nice, but wish it was a #2. The bit driver would be nice If I hadn't lost the spring or if it's replacement would come in the mail before the end of the challenge. (I plan to use some heat shrink as mentioned by MTO aficionado.) Tool covers/comfort grips got removed very quickly. I am in agreeance with other MTOers when it comes to wishing SOG would have rolled the edges instead of using the comfort grips. I like the compound gripping power, but don't like that you can't open one side of the tool at a time for longer reach. The tools seem too close together and open as I am trying to get other tools open. And lastly, the nail nicks are very little help to open each tool.I do like the plier head being rounded and the wire strippers/cutters work well. The pliers are very smooth to open and close. I find myself opening and closing them.


-
A week has passed since my Powerlock blade SNAFU.... Finger is healing slowly. I took the rest of the nail off even though it was still attached. Thought I'd post a few pics.


Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login