Skeletool RX?
-
@50ft-trad said:
@captain spaulding said:
Haha, I knew they mistakingly put the names on their website and they lied to us when we asked about it. I knew they were lying.
Yup! "Typo" - yea right

Yup, further fuelling my distrust. SOG go
that shouldn't be in circulation when new product info sneaks out, Leatherman just blatantly lies. Says a lot about a company when they're so comfortable to lie to their customer baseYes they lied, but it doesn't bug me since i'm sure the employee signed a confidentiality contract when employed. If they confirmed the existence of it before they were supposed to the employee would of lost their job.
-
I demand that leatherman sell the glass breaker bit separately for my wave.. and my skeletool... and my bit kit... and my bit adapter for my super tool...... this may get expensive
-
@rescue4500 said:
I demand that leatherman sell the glass breaker bit separately for my wave.. and my skeletool... and my bit kit... and my bit adapter for my super tool...... this may get expensive
yep -
@rescue4500 said:
I demand that leatherman sell the glass breaker bit separately for my wave.. and my skeletool... and my bit kit... and my bit adapter for my super tool...... this may get expensiveAgreed. I need a few of those bits for sure.
-
@captain spaulding said:
I demand that leatherman sell the glass breaker bit separately for my wave.. and my skeletool... and my bit kit... and my bit adapter for my super tool...... this may get expensive
Agreed. I need a few of those bits for sure.
I want one too.
-
Wow, what better way than this to encompass 12 months of multitool bleeding edge innovation, Leatherman!
Your R&D department must be buzzing...hive of activity!
-
Disappointing.

-
@captain spaulding said:
@50ft-trad said:
@captain spaulding said:
Haha, I knew they mistakingly put the names on their website and they lied to us when we asked about it. I knew they were lying.
Yup! "Typo" - yea right

Yup, further fuelling my distrust. SOG go
that shouldn't be in circulation when new product info sneaks out, Leatherman just blatantly lies. Says a lot about a company when they're so comfortable to lie to their customer baseYes they lied, but it doesn't bug me since i'm sure the employee signed a confidentiality contract when employed. If they confirmed the existence of it before they were supposed to the employee would of lost their job.
Point taken Cap'n, but regardless of the reasoning, I still think it paints a bad picture when a supposedly customer facing company is caught lying to it's patrons. There's a big difference between someone there volunteering strategic marketting or development news, and having the integrity to hold your hand up and acknowledge albeit downplayed a data leak or other issue.
I'm not trying to colour other people's views, but it leaves a bitter taste with me. It's certainly not how I would have handled it, and I'd value having the company being trusted on it's word more highly than keeping a new product secret for an extra month.
It's not an anti-Leatherman stance either, in case anyone thinks "Al's at it again" :D. I'm not exactly known for singing the praises of SOG, but they handled it so much better, acknowledging a slip, and even sending out a few goodies to the guy that flagged it
-
@50ft-trad said:
@captain spaulding said:
@50ft-trad said:
[quote author=captain spaulding link=topic=62309.msg1213831#msg1213831 date=1453249532]
Haha, I knew they mistakingly put the names on their website and they lied to us when we asked about it. I knew they were lying.Yup! "Typo" - yea right

Yup, further fuelling my distrust. SOG go
that shouldn't be in circulation when new product info sneaks out, Leatherman just blatantly lies. Says a lot about a company when they're so comfortable to lie to their customer baseYes they lied, but it doesn't bug me since i'm sure the employee signed a confidentiality contract when employed. If they confirmed the existence of it before they were supposed to the employee would of lost their job.
Point taken Cap'n, but regardless of the reasoning, I still think it paints a bad picture when a supposedly customer facing company is caught lying to it's patrons. There's a big difference between someone there volunteering strategic marketting or development news, and having the integrity to hold your hand up and acknowledge albeit downplayed a data leak or other issue.
I'm not trying to colour other people's views, but it leaves a bitter taste with me. It's certainly not how I would have handled it, and I'd value having the company being trusted on it's word more highly than keeping a new product secret for an extra month.
It's not an anti-Leatherman stance either, in case anyone thinks "Al's at it again" :D. I'm not exactly known for singing the praises of SOG, but they handled it so much better, acknowledging a slip, and even sending out a few goodies to the guy that flagged it
[/quote]Ohh no, Al is at it again
I understand what you mean but never forget:
You know as well as I do decisions made in real time are never perfect.
If you look around in any company, you will have similar hick-ups (that's what this is to me) all the time... most just never come to light or are quickly forgotten. Ultimately, if that is the worst LM does it's still a great company.
-
Dig the color of the "new" Skeletal but eh. I'd also love one or 3 of those bits too.
-
they'll have to sell the breaker bit as a replacement part for the rx.... right??
-
Is no one else concerned about the bit adapter holding up to the strain of punching through a window? I've never actually done it, but doesn't breaking a window require a fair amount of force?
-
@sLaughterMed said:
Is no one else concerned about the bit adapter holding up to the strain of punching through a window? I've never actually done it, but doesn't breaking a window require a fair amount of force?I'm kinda more bothered by the idea that you have to either open of half open the tool to use the glass breaker.....
-
Is no one else concerned about the bit adapter holding up to the strain of punching through a window? I've never actually done it, but doesn't breaking a window require a fair amount of force?
I'm kinda more bothered by the idea that you have to either open of half open the tool to use the glass breaker.....
I think it would be annoying, and slightly fiddly, but not terrible. You'd just have to hold it like this, only backwards:

(pic blatantly
stolenborrowed from J-Sews
)I'd really be more concerned about the other side of the glass breaker bit getting ruined (when it pushes against the bit holder), or busting completely through the bit holder, not to mention screwing up the bit lock.
-
Is no one else concerned about the bit adapter holding up to the strain of punching through a window? I've never actually done it, but doesn't breaking a window require a fair amount of force?
I'm kinda more bothered by the idea that you have to either open of half open the tool to use the glass breaker.....
I think it would be annoying, and slightly fiddly, but not terrible. You'd just have to hold it like this, only backwards:

(pic blatantly
stolenborrowed from J-Sews
)I'd really be more concerned about the other side of the glass breaker bit getting ruined (when it pushes against the bit holder), or busting completely through the bit holder, not to mention screwing up the bit lock.
I was thinking about that exact point this morning. But then I thought about the scenario for using the tool: emergencies. If someone is bleeding out in an over-turned vehicle, or stuck in a vehicle that is on fire, the well being of your tool is an afterthought when the well being of a life is in jeopardy. You probably wouldn't ever use the glass-breaker except under duress. If you were going to use it for gee-whizz, I think you'd have to weigh the risk vs reward.
Surely Leatherman tested it, right?
-
Is no one else concerned about the bit adapter holding up to the strain of punching through a window? I've never actually done it, but doesn't breaking a window require a fair amount of force?
I'm kinda more bothered by the idea that you have to either open of half open the tool to use the glass breaker.....
I think it would be annoying, and slightly fiddly, but not terrible. You'd just have to hold it like this, only backwards:

(pic blatantly
stolenborrowed from J-Sews
)I'd really be more concerned about the other side of the glass breaker bit getting ruined (when it pushes against the bit holder), or busting completely through the bit holder, not to mention screwing up the bit lock.
I was thinking about that exact point this morning. But then I thought about the scenario for using the tool: emergencies. If someone is bleeding out in an over-turned vehicle, or stuck in a vehicle that is on fire, the well being of your tool is an afterthought when the well being of a life is in jeopardy. You probably wouldn't ever use the glass-breaker except under duress. If you were going to use it for gee-whizz, I think you'd have to weigh the risk vs reward.
Surely Leatherman tested it, right?
I absolutely agree. If I found myself in a situation like that, I wouldn't hesitate for a second to use the tool, regardless of the damage to the tool.
However, this tool is aimed at emergency response personel, who likely have a need to use tools like glass breakers very often (sometimes even multiple times a day). So the question is, will this tool work long term for someone in that line of work? Im not convinced that the skeletool frame will hold up to multiple strikes on the bit adapter
-
@sLaughterMed said:
Is no one else concerned about the bit adapter holding up to the strain of punching through a window? I've never actually done it, but doesn't breaking a window require a fair amount of force?that's a good point.. as a former extrication technical rescuer I can say this... as long as what your breaking the glass with is a small point and strong material it doesn't take that much force.. just the opposite if your using a larger point to break glass it take much more force.. which is why most rescue squads and fire departments carry a couple spring loaded punches on each truck to break windows with.. its strong and requires little force to do saving time and effort
-
Is no one else concerned about the bit adapter holding up to the strain of punching through a window? I've never actually done it, but doesn't breaking a window require a fair amount of force?
I'm kinda more bothered by the idea that you have to either open of half open the tool to use the glass breaker.....
I think it would be annoying, and slightly fiddly, but not terrible. You'd just have to hold it like this, only backwards:

(pic blatantly
stolenborrowed from J-Sews
)I'd really be more concerned about the other side of the glass breaker bit getting ruined (when it pushes against the bit holder), or busting completely through the bit holder, not to mention screwing up the bit lock.
TBH,the photo demonstrates exactly my concern. I wouldn't fancy having to strike glass holding a shape like that.
It's also a bit of a moot point...I sold my Skeli years ago,and have never missed it ;)
-
I can see LM selling LOTS of those glass breaker bits from the Skeletool RX ( so long as they fit other LM bit holders and LM choose to market them).
I think they will. They'd be dumb to not sell them. And they will work better in the Wave/Charge/Surge than in the Skeletool since you can lock the driver out with the tool closed - better grip. With the Skele, you would be striking the window with the tool either half opened - which could then collapse at the pliers, or fully opened - which would be awkward whilst striking. I don't understand why they wouldn't work something onto the outside of the carabiner area for glass breaking. Or at least make the glass breaker bit long enough to protrude past the carabiner
I am still not sure how practical the glass break bit is, sine it took the place of phillip drive, which I think it is one of the most Frequently used tool.
Most LM only holds one bit, if you store the glass break bit in MT that means you will have to get out the bit kit often. Or if you store the glass break bit somewhere else, do you think there will enough time to get it installed in case of emergency? -
I can see LM selling LOTS of those glass breaker bits from the Skeletool RX ( so long as they fit other LM bit holders and LM choose to market them).
I think they will. They'd be dumb to not sell them. And they will work better in the Wave/Charge/Surge than in the Skeletool since you can lock the driver out with the tool closed - better grip. With the Skele, you would be striking the window with the tool either half opened - which could then collapse at the pliers, or fully opened - which would be awkward whilst striking. I don't understand why they wouldn't work something onto the outside of the carabiner area for glass breaking. Or at least make the glass breaker bit long enough to protrude past the carabiner
I am still not sure how practical the glass break bit is, sine it took the place of phillip drive, which I think it is one of the most Frequently used tool.
Most LM only holds one bit, if you store the glass break bit in MT that means you will have to get out the bit kit often. Or if you store the glass break bit somewhere else, do you think there will enough time to get it installed in case of emergency?It looks like the bit in the handle is the combo flat/phillips bit, like the one that comes in the Wave. The opposite of the glass-breaker also appears to be a flat. I think the idea with the RX, is to leave the glass-breaker in, and swap to the Phillips or flat as needed, and then switch it back afterwards. At least that is how I would do it, because you are right, if you were rocking the Phillips (which I use most of the time) while driving down the road and a car crash happens right in front of you, probably would not be good trying to fumble around with a tiny bit while responding.
I think probably EMTs, Police Officers, or other emergency responders would not use this, at least not as a primary rescue tool. Maybe a backup. They would all probably have access to something better. A ResQme is a better glass breaker. A strap cutter removes virtually ALL chance of accidentally cutting the victim. I think this is a pretty decent combo of an EDC mulitool and a ER tool, but it could have been a lot better.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login