CIMA P5 Multitool, first look
-
Boy is it ugly! >:D
-
Looks a lot like this: http://sunpointool.com/En/ProductView.asp?ID=10140
-
It must be the same product. :)
I have done most of the tests I wanted and I will write a bit more soon. Not bad.
-
I have to say I'll be watching this with interest.
We have a reputation for honest reviews of tools. We have a reputation for honesty full stop. Please don't get me wrong,I'm not casting aspersions on dks.
But given the background to the supply of this tool,I hope the manufacturer understands they won't buy a good review. Leatherman can't! Gerber can't! Victorinox can't!
If the this review ends with with a negative,I hope the manufacturer takes on board to improve their product. If it gets turned on MTo,as others have tried,we will defend our honour and reputation!
-
I used this in the same way and even harder than I would have used a branded multitool of the same size.
Pliers.I first cut some 1.5mm steel wire.
This was done easily, both in the hard wire notch and in the regular part of the cutters.

The only visible change was some removal of the coating on the cutters, at the point where I was cutting.
Then I tried to cut stranded wire, 2mm, used for clothes lines etc.
This was not cut properly with the first cut.
I had to turn it and try again 3 times to cut it.

This is a common issues with cutters of that style, which I also face with the LM ST300. However the ST300 has speSmurfpillsed stranded wire cutters too, which work much better.
No major damage, though I think that there was some scratching on the edge.
Then I tried to see whether it could cut the metal, nail part, of rivets.
I used 3 rivets, sized 1.7mm, 2.2mm and 2.57mm.


The 1.7mm and 2.2mm ones were cut reasonably easily.
In both cases one part of the river went flying and I could not be bothered to look for it.
1.7mm
2.2mm

The 2.57mm one proved impossible to cut. I applied force using both hands but the leverage just wanted there (I am not the weakest bloke). I tried the hard wire notch and the regular cutter part.
Here is what it looked like afterwards.
I need to get Tim Leatherman to give me the device he uses to cut nails with his tools, during special demonstrations :D ..
And the pliers
The pliers still felt as tight as before.
The Saw.
The tool that actually impressed me was the saw. I expected it to be rubbish but I was able to cut the wood I was using really easily (soft pine). It seems to be on par with the established multitool saws, at least on cutting, if not on longevity.
A few seconds work


The awl/reamer
I wanted to start a hole for screwing and used the awl. It worked.
Screwing
I chose a hefty screw and went ahead.
I used the Philips screwdriver.
It fits the screw well.
I managed to screw the screw two thirds in, when I started to feel the screwdriver flexing a bit and slipping. I pushed a bit more and there was some damage to the head of the screwdriver.
The small “flaps”, for lack of a better word, as can be seen have bend a bit.

I then used a proper screwdriver and was able to screw it in a bit more, with effort. I think that the multitool screwdriver was pushed more than necessary, but I had to find its limit. A proper screwdriver, like that of an ST300 would not have suffered any damage, had I applied the same force, but I would not have regularly used a screwdriver of the type found on the Cima with that much force.
I do not like abusing tools and felt guilty for the damage.
I also used the screwdriver on the can opener for a turn, after the main one failed and it did not appear damaged, though I could feel it flexing a bit.

I tried to use the screwdrivers at a 90 degree angle, as they have a halfstop, but that was not very successful. The springs do not have enough strength to support them in that position and they kept closing. A good idea, but only for emergency situations.
I also shaved some wood with the blade, and it was unaffected.
Summarising, I have to say that it appears to be a good tool, for its price point.
It would have been better if it had:
one less flat screwdriver and a more robust Philips,
stronger backsprings,
a better sheath,
better aligned pliers and
a way to replace the cutters.
Also, with a tool like that you only have the sellers guarantee, which will vary from seller to seller.There are ofcourse a several no brand/Ganzo products at that price point but not many with the hard cutters and interesting looking blade.
Would I buy it? Possibly not, as I have several branded tools that get little use anyway.
However it is cheap, solid enough, especially with regard to the pliers, blade and saw and seems well finished/made. **It should serve any non-multitool fanatic well.
It should also serve well as a “beater” tool**, for when you do not want to risk damaging a more expensive tool.


-
I was fairly impressed with this tool until its Phillips got damaged. Being one of my most used implements this is super uncool. I do see potential though and wouldn't mind seeing more from this manufacturer.
-
Dks can't even do a multitool review without getting round to the topic of "flaps" ::)
:D
Nice write up feller
On the whole it seems quite a capable multitool for the money. I think the biggest hurdle for me might be ergonomics, though as we know, one of the market leaders can't get that right either. It also seems to suffer "Swiza Syndrome" with the tools sitting so high out of the handle. Laid flat that is a very wide multitool, and that's got to have an impact on ergos for a lot of people.I wouldn't buy one, purely based on my impressions of the ergonomics. If it wasn't for that, then yes I'd be willing to spend $20 on it.
Thanks for the insights and time taken to put this together

-
If I was writing this in Scotland I would have been calling them wee flaps....
The ergonomics for using the tools are better than for the pliers, but even when I was squeezing the handles hard trying to cut things my hand did not slip.It seems to have been designed so that you can use the knife comfortably, more than anything else.
The Philips screwdriver seems to always be the weak point with cheap Chinese tools.
-
Interesting find, and what a nice collection!
I think it is distinctive in it's own way - albeit a of a pain in the eyeballs.
Great review!
The saw seems like a winner. The wire cutters could also prove to be better than most, despite their unique non-replecablility-ability
Would be interesting what they come up with next!
-
Thank you.
They make knives too, but I have no idea if they are any good.
-
Thank you for the great review!
I am surprised about the somewhat positive thoughts on this tool. With all the problems and nothing really working as designed with the one exception of the saw it seems like a complete failure in my opinion.

I wouldn't touch this tool with a 10 foot pole let alone spend money on one. Not trying to be a downer, just being honest.
-
The blade and pliers worked and the screwdrivers did okish.
For the same money all we get is the Vic classic.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login