jlwatso1's 31 Day SOG Super Power Badge Quest
-
Day 16
Enjoyed getting to read to my daughter while she drank her Orange juice this morning. Then got Powerlocked and loaded to go to Home Depot.


-
Did a handle upgrade to a table my wife's parents gave us. Used the flathead. Took a couple before and after pics.




-
@Alan K. said:
Don't let me stop you. You're very lucky to still have that fingertip.
Remember, pain is temporary, glory is everlasting, and chicks dig scars.
I know that's for sure glad I didn't lose the tip. Cool quote.
Is it an original?One of the reenactment groups I used to belong to had a sub-group that performed live steel (both impromptu and choreographed) sword fighting demonstrations, living chess games, melees, and battle reenactments. The fighters took great care to practice safety measures, but broken fingers and lacerations were common, even with blunted blades. They had the saying printed on T shirts, but they had it in Latin.
Dolor transit Gloria aeterna est Pullos fodere cicatrices
It sounds better in Latin, but everything usually does.
-
@Alan K. said:
@Alan K. said:
Don't let me stop you. You're very lucky to still have that fingertip.
Remember, pain is temporary, glory is everlasting, and chicks dig scars.
I know that's for sure glad I didn't lose the tip. Cool quote.
Is it an original?One of the reenactment groups I used to belong to had a sub-group that performed live steel (both impromptu and choreographed) sword fighting demonstrations, living chess games, melees, and battle reenactments. The fighters took great care to practice safety measures, but broken fingers and lacerations were common, even with blunted blades. They had the saying printed on T shirts, but they had it in Latin.
Dolor transit Gloria aeterna est Pullos fodere cicatrices
It sounds better in Latin, but everything usually does.
That's pretty cool. Thanks for sharing!
-
DAY 17
Not much to report today. Just did a little Powerlock pocket carry to church.
-
DAY 18
Used the Powerlock to pull an ingrown hair! That's some tweezer like persition! Hopefully Deadmun gets a little more use than this today, just thought I would share this pic at the moment. :D

-
Did a change out on the air to water VRF and installed an air to air VRF for testing. Wired in high voltage and com. Use wire strippers as well, just didn't have a chance to take a pic of the strippers in use. Here's a few action shots. Wiring high voltage, tightening static taps. Last few were cutting Armaflex to cover 1 5/8", 1 1/8", 5/8", and 3/8" copper.




-
DAY 19
Off day, just ran errands today. Picked up a key chain tape measure and had to use the knife on the PL to open it. Then cleaned up the garage some while my little girl took her nap. Used the knife again to break down some boxes to have the recycle company pick up tomorrow.


-
Changed the water filter in the fridge. Needed a little help from my Powerlock.

-
DAY 20
Pork tenderloin with Tuscan seasoning from Costco!




-
DAY 21
PL didn't see a whole lot of action today. Just used it to change socks for wet bulb readings and work on some static taps. My spring came in for the 1/4 driver the other day. I haven't put it on yet because I want to put some heat shrink on it like I saw a thread for on here the other day.


-
DAY 22
Used my Powerlocks to strip and crimp connections on a new ground wire to replace one with the insulation burned off. Later I used the pliers as an ice pick. I was trying to cool down some recovery tanks for some R-410a to keep the pressure down where it wouldn't trip the high pressure control on the recovery machine. Recovered about 125 lbs.


-
DAY 23
Didn't do a whole lot today. Thought I would snap a picture of the EDC tools that the Powerlock has been riding around with in my pouch. Next picture is the rest of my EDC. Not pictured is my i-phone 6s. Had to use it to take the pictures.


-
DAY 24
Put myreplacement Spring on my Powerlock today. Used some heat shrink to hold it on as seen in another thread.


-
DAY 24
Put myreplacement Spring on my Powerlock today. Used some heat shrink to hold it on as seen in another thread.
How does it fold now? Seems to me like the tubing would be in the way for the adjacent tools? Considering doing the same before I lose the spring.
Mine catches on the screwdriver just a little bit more when I deploy the 1/4" drive, but it seems like all the tools do that any way... You should try it, worst case- you cut it off if you don't like it. Took me a couple trys for the heat shrink not to break. Don't apply too much heat and make sure you have a clean edge- no nicks.
-
DAY 25
Not a whole lot of action for the Powerlock today. Just tightening some static taps. Here's a beauty shot on my drill press.

-
It looks like that drill press was made back when the Kraken was a guppy. You can't beat old tools when they work, but just try to track down a part when they don't.


-
@Alan K. said:
It looks like that drill press was made back when the Kraken was a guppy. You can't beat old tools when they work, but just try to track down a part when they don't.

It was my grandpa's. My parents still have his old lathe and machinist's drill press back home in Oklahoma. I hope to add them to my collection as well. I enjoy getting to work on things with his tools. Brings back memories of him.
-
@Alan K. said:
It looks like that drill press was made back when the Kraken was a guppy. You can't beat old tools when they work, but just try to track down a part when they don't.


It was my grandpa's. My parents still have his old lathe and machinist's drill press back home in Oklahoma. I hope to add them to my collection as well. I enjoy getting to work on things with his tools. Brings back memories of him.
That is a really cool heirloom.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login