jlwatso1's 31 Day SOG Super Power Badge Quest
-
Changed the water filter in the fridge. Needed a little help from my Powerlock.

-
DAY 20
Pork tenderloin with Tuscan seasoning from Costco!




-
DAY 21
PL didn't see a whole lot of action today. Just used it to change socks for wet bulb readings and work on some static taps. My spring came in for the 1/4 driver the other day. I haven't put it on yet because I want to put some heat shrink on it like I saw a thread for on here the other day.


-
DAY 22
Used my Powerlocks to strip and crimp connections on a new ground wire to replace one with the insulation burned off. Later I used the pliers as an ice pick. I was trying to cool down some recovery tanks for some R-410a to keep the pressure down where it wouldn't trip the high pressure control on the recovery machine. Recovered about 125 lbs.


-
DAY 23
Didn't do a whole lot today. Thought I would snap a picture of the EDC tools that the Powerlock has been riding around with in my pouch. Next picture is the rest of my EDC. Not pictured is my i-phone 6s. Had to use it to take the pictures.


-
DAY 24
Put myreplacement Spring on my Powerlock today. Used some heat shrink to hold it on as seen in another thread.


-
DAY 24
Put myreplacement Spring on my Powerlock today. Used some heat shrink to hold it on as seen in another thread.
How does it fold now? Seems to me like the tubing would be in the way for the adjacent tools? Considering doing the same before I lose the spring.
Mine catches on the screwdriver just a little bit more when I deploy the 1/4" drive, but it seems like all the tools do that any way... You should try it, worst case- you cut it off if you don't like it. Took me a couple trys for the heat shrink not to break. Don't apply too much heat and make sure you have a clean edge- no nicks.
-
DAY 25
Not a whole lot of action for the Powerlock today. Just tightening some static taps. Here's a beauty shot on my drill press.

-
It looks like that drill press was made back when the Kraken was a guppy. You can't beat old tools when they work, but just try to track down a part when they don't.


-
@Alan K. said:
It looks like that drill press was made back when the Kraken was a guppy. You can't beat old tools when they work, but just try to track down a part when they don't.

It was my grandpa's. My parents still have his old lathe and machinist's drill press back home in Oklahoma. I hope to add them to my collection as well. I enjoy getting to work on things with his tools. Brings back memories of him.
-
@Alan K. said:
It looks like that drill press was made back when the Kraken was a guppy. You can't beat old tools when they work, but just try to track down a part when they don't.


It was my grandpa's. My parents still have his old lathe and machinist's drill press back home in Oklahoma. I hope to add them to my collection as well. I enjoy getting to work on things with his tools. Brings back memories of him.
That is a really cool heirloom.
-
Day 26
Off day today. No action for the Powerlock. Just pocket carried. Here's a pic of the Powerlock posing for the camera.

-
DAY 27
Just change socks for the wet bulb readings on the room this morning. Just a bunch of screen watching on another VRF. Wall mout units this time 6 in each of the two rooms. Got the 100% (80/67-95), 75%(80/67-81.5), 50% 80/67-68), and 25% (80/67-65) cooling tests completed and set the room for high temp heating (70/<60- 47/43) before ending my shift. Hopefully night shift will be able to get it out along with SCHE [Simultaneous Cooling and Heating (Outdoor room set to Heating conditions 47/43), one indoor room set to Cooling 80/67 and the other indoor room set to heating conditions 70/<60.] , and then low temp heating 17/15 outdoor. I'm sure that was TMI but thought I would go into a little more detail if anyone was interested. Here's anther beauty shot.

-
DAY 28
Got to work and the tests were complete. Wasn't feeling too good, but chose to stick it out the rest of the day. Used my Powerlock Pliers to grip and remove a screw that had the Philips head stripped out after breaking off the long threads sticking through the plywood wall.(Sorry no pics of that.) Managed to pinch a blood blister on my hand on the next one I tried and had to resort to the sawzaw. Then used them to smash the ends of some copper lines before putting some tape on them to keep trash out. Lastly, I used the knife to cot some Armaflex while insulating copper for the next setup.



-
Gnarly
-
DAY 29
Worked on a VRF setup we started on yesterday. Used my Powerlock to woller out copper after using the tubing cutters. Thought I would share a few pictures.




-
What are you working on?
Sent from my iPhone using Tapatalk
-
It is a VRF (Variable Refrigerant Flow) Heatpump system we are setting up in a Psycrometric Chamber. We test other HVAC systems as well. This one is a 24 ton with 3 Outdoor units and 12 indoor units (6 in each indoor room).
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
