Newbie modding SAKs
-
@m47mu74nt said:
...at most those amateur builds will become gifts for friendsYour friends should be happy!
-
Good stuff! I like when people do progress pics, its nice to see how people work and step by steps are much more interesting then just posting the final build. In fact many successful blade makers started off and gained popularity specificly because they showed how they do their work. It draws in an audience.
Some things I thought while reading.
The liners are the best templates as you discovered. I use little clamps to hold them on the material then scribe lines around and remove. I used double sides tape before too.. annoying. :D
I didnt realize how much Ti-6-4 hardens when heated so if you are using any method to cut them that involves heat, drill holes first. This really caught me off guard when I made the fold over clip on the mini champ. It was impossible to tap the holes in that scale after it was heated to fold.
I grind/sand my scales in fully assembled knife mode to get them exactly flush with the backspring. I dont use the 'good' parts that will be in the final build, just junker old ones. Its the only way I can get the perfectly flush.
Keep up the great work!
-
Thanks for sharing, I love to see this sort of project. I think this one looked very nice, I like the 'dead hole' details, it adds a little something. Nice work [emoji1]
-
I hope so :)
@Syph007 said:
Good stuff! I like when people do progress pics, its nice to see how people work and step by steps are much more interesting then just posting the final build. In fact many successful blade makers started off and gained popularity specificly because they showed how they do their work. It draws in an audience.thank you, the issue with WIP is that it's difficult to both think about taking pictures and building, at least for newbies :D
@Syph007 said:
Some things I thought while reading.The liners are the best templates as you discovered. I use little clamps to hold them on the material then scribe lines around and remove. I used double sides tape before too.. annoying. :D
hmmm so you don't pre-drill through the liners? as i don't have a good drill press, i need them in place to guide the drill bit :-\
@Syph007 said:
I didnt realize how much Ti-6-4 hardens when heated so if you are using any method to cut them that involves heat, drill holes first. This really caught me off guard when I made the fold over clip on the mini champ. It was impossible to tap the holes in that scale after it was heated to fold.This explains the behavior i faced when trying to cut Ti with the angle grinder!
@Syph007 said:
I grind/sand my scales in fully assembled knife mode to get them exactly flush with the backspring. I dont use the 'good' parts that will be in the final build, just junker old ones. Its the only way I can get the perfectly flush.Keep up the great work!
nice tip! though i can't follow it until i have enough spare parts to make a dummy build dedicated to grinding, for now i already used the two non limited series of SAKs i had.. (the green Classic SD, and that Ecoline Nylon Sentry)
@Boaz said:
Thanks for sharing, I love to see this sort of project. I think this one looked very nice, I like the 'dead hole' details, it adds a little something. Nice work [emoji1]Here are some better pics: (i've notice with these that my rivets are far from "nice" so i reworked them a little [no pic yet])
The dead holes aren't perfect either, looks like the old milling cutter (dremel one) i used didn't do it's job [or i failed using it
]
This time the color scheme is much closer to reality!



-
Some things I thought while reading.
The liners are the best templates as you discovered. I use little clamps to hold them on the material then scribe lines around and remove. I used double sides tape before too.. annoying. :D
hmmm so you don't pre-drill through the liners? as i don't have a good drill press, i need them in place to guide the drill bit :-\
Oh yes I do use the liners as drilling templates too. But I actually take 4-5 liners rivetted together for that purpose so its a nice thick stack. I use this to drill that hidden 4th hole in all the 91mm Ti scales I do.
-
@Syph007 said:
Oh yes I do use the liners as drilling templates too. But I actually take 4-5 liners rivetted together for that purpose so its a nice thick stack. I use this to drill that hidden 4th hole in all the 91mm Ti scales I do.Is there any thing i should really know before messing with a 91mm? i'd like to make one for a friend's birthday, but before failing i need some advices: is that much more complicated than a Classic?
i've already found that peening the 84mm rivets (used 2.0mm brass rod) is slightly more complicated than the 1.5mm i used for the Classic. Plus i'm a little worried about the back tools...On another subject i'm preparing a post about my process of bi-color anodizing, if anybody wants to make colored recessed swiss cross in their Ti builds that could help :) (it is not a revolution, but it's quite different from what i've read before starting)
-
I used 2x2.5mm and 2x2mm brass nails. I think 2.5mm on ends were easier. Also I did some errors with tools so had to rebuild my handyman plus. So good to check everything before peening. I would like to know if there would be simple tools and parts to do riverts like vic have (no need for hammering). Looks like pressed.
-
Very nice work!!!!
Marcelo, from Argentina
-
@temo said:
I used 2x2.5mm and 2x2mm brass nails. I think 2.5mm on ends were easier. Also I did some errors with tools so had to rebuild my handyman plus. So good to check everything before peening. I would like to know if there would be simple tools and parts to do riverts like vic have (no need for hammering). Looks like pressed.This video gives us a clue : https://youtu.be/qIpr1_wmvDs
The rivets are friction and press fitted, the tool they use spins and press the rivet end (2min 15sec) -
Very nice looking work M


-
Victorinox uses an orbital rivet machine in that video.
-
Tx. Yes called pushies or something. Should work with more simple tool then press as well (hammer and hit tool). Though should find some first.
-
I don’t know about you Guys but I save interesting pictures I find on the net
Not sure where I found it but this one might be useful to you M?
-
@Sparky415 said:
I don’t know about you Guys but I save interesting pictures I find on the net
Not sure where I found it but this one might be useful to you M?
In fact this chart works with a whole piece of Ti dipped in the electrolytic solution (H2SO4, water).
For very small parts of using a cotton/brush, the chart is slightly different (this is the exact same spectrum) but the voltages aren't the same:
I could get a light 'urine' yellow at 57V (+lemon juice) with a small cotton and multiple passes even if the chart says you should get that at 70V+It is a good base of work, but it won't give you predictable results unless your are in the same exact conditions of the chart
i've tried to give an explanation here : /topic/64287
-
Excellent thread mate. :ahhh Nice to have you here.
And congrats on the badges. 
-
Excellent thread mate. :ahhh Nice to have you here.
And congrats on the badges. 
Thank you, there might be some time before next project coming though

Wouah, 3 badges at once :D thanks! :ahhh
Can't stop once you pop. :P
-
-
I suddenly thought the donor scales deserved a picture too, so ...
91mm : Red Cellidor Compact
84mm : Nylon Sentry
58mm : Green Cellidor Classic SD
-
Next project : Ti-Rambler
(i'm using scales i started to make during previous project)
disassembling :
the parts:
drilled a [bigger] bevel:
pre-pinning the rivets:
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

