Newbie modding SAKs
-
Very nice work!!!!
Marcelo, from Argentina
-
@temo said:
I used 2x2.5mm and 2x2mm brass nails. I think 2.5mm on ends were easier. Also I did some errors with tools so had to rebuild my handyman plus. So good to check everything before peening. I would like to know if there would be simple tools and parts to do riverts like vic have (no need for hammering). Looks like pressed.This video gives us a clue : https://youtu.be/qIpr1_wmvDs
The rivets are friction and press fitted, the tool they use spins and press the rivet end (2min 15sec) -
Very nice looking work M


-
Victorinox uses an orbital rivet machine in that video.
-
Tx. Yes called pushies or something. Should work with more simple tool then press as well (hammer and hit tool). Though should find some first.
-
I don’t know about you Guys but I save interesting pictures I find on the net
Not sure where I found it but this one might be useful to you M?
-
@Sparky415 said:
I don’t know about you Guys but I save interesting pictures I find on the net
Not sure where I found it but this one might be useful to you M?
In fact this chart works with a whole piece of Ti dipped in the electrolytic solution (H2SO4, water).
For very small parts of using a cotton/brush, the chart is slightly different (this is the exact same spectrum) but the voltages aren't the same:
I could get a light 'urine' yellow at 57V (+lemon juice) with a small cotton and multiple passes even if the chart says you should get that at 70V+It is a good base of work, but it won't give you predictable results unless your are in the same exact conditions of the chart
i've tried to give an explanation here : /topic/64287
-
Excellent thread mate. :ahhh Nice to have you here.
And congrats on the badges. 
-
Excellent thread mate. :ahhh Nice to have you here.
And congrats on the badges. 
Thank you, there might be some time before next project coming though

Wouah, 3 badges at once :D thanks! :ahhh
Can't stop once you pop. :P
-
-
I suddenly thought the donor scales deserved a picture too, so ...
91mm : Red Cellidor Compact
84mm : Nylon Sentry
58mm : Green Cellidor Classic SD
-
Next project : Ti-Rambler
(i'm using scales i started to make during previous project)
disassembling :
the parts:
drilled a [bigger] bevel:
pre-pinning the rivets:
-
Looking good


-
Looking good


sadly next steps might be in a few weeks, i won't be able to finish it before

I'll be waiting

-
Awesome work...
I've always wanted to do through peening work on 58mm series... How much excess do we need to leave out? Have only done 91mm peening with the bushings in place and always leave 1mm for peening..
Sent from my iPhone using Tapatalk
-
I left a little less than 1mm iirc on previous build,
But, with the bevel I might need a little more to get the V shape in the scale and still a rounded tip
I'll tell you after this one :DBTW, 1.6mm diameter rod is a little thinner than the holes (like 1.65mm?) Which gives some smoothness (some might say a beginning of wobble)
-
DIY of the day: Ti pocket clip
Hammered and flame-anodized titanium
Thank to Syph007 for bending tip

-
@m47mu74nt said:
DIY of the day: Ti pocket clip
Hammered and flame-anodized titaniumLooks awesome [emoji8][emoji8][emoji8]
Sent from my iPhone using Tapatalk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
