Show off your Sak mod's!
-
Epoxy resin could be one thing to test. You could put other then leather inside as well (insects etc..) But yes could work. Edges from leather at least handle with some stuff.
-


Original scales had trouble to stay place with mod riverts so did scales from chopping board. Ice blue mod. Not the winner of beauty contest but quite okay to handle.
-
Finished this one with an inline awl. The awl had a broken tip, so I had to shorten it a little.
Also working on GAK rebuilds. Top row is all VIC with new blades except for one.
Bottom row are mix-and-match rebuilds of other brands...two Adlers, Aitor and a B&H. Still have a pile of them to work on...mostly ICARs


-
@Spork, Lord of Lime Jello! said:
Finished this one with an inline awl. The awl had a broken tip, so I had to shorten it a little.Also working on GAK rebuilds. Top row is all VIC with new blades except for one.
Bottom row are mix-and-match rebuilds of other brands...two Adlers, Aitor and a B&H. Still have a pile of them to work on...mostly ICARs
That's nice Spork,looks like a real workmanship SAK

-
Thanks. I've known about the inline awl mod for years...just didn't want to sacrifice an Alox knife for it. The blade was pretty well sharpened down too. The scales and opener layer are going to get pinned together as a bar tool

I've sorted out enough parts for three Woodsman...they are going to replace the SAKs that live permanently in packs I use. Currently there is a Rucksack, Huntsman and Camper.
-
@Spork, Lord of Lime Jello! said:
Finished this one with an inline awl. The awl had a broken tip, so I had to shorten it a little.Also working on GAK rebuilds. Top row is all VIC with new blades except for one.
Bottom row are mix-and-match rebuilds of other brands...two Adlers, Aitor and a B&H. Still have a pile of them to work on...mostly ICARs
Lovely Spork! Out of interest (as I'm about to embark on a mod myself) did the awl drop in ok as it is?
Looking forward to pics of the Woodsmen - my fave SAK!
-
@Spork, Lord of Lime Jello! said:
Finished this one with an inline awl. The awl had a broken tip, so I had to shorten it a little.
Also working on GAK rebuilds. Top row is all VIC with new blades except for one.
Bottom row are mix-and-match rebuilds of other brands...two Adlers, Aitor and a B&H. Still have a pile of them to work on...mostly ICARs
Lovely Spork! Out of interest (as I'm about to embark on a mod myself) did the awl drop in ok as it is?
Looking forward to pics of the Woodsmen - my fave SAK!
Spring tension is good...walks and talks. I was a little bit apprehensive because of the slightly larger pivot hole and the tang seeming to be a hair thicker, but it seems to work.
-
Thanks.

I see you have set it in behind the cap lifter - does the edge of the awl sit on the cap lifter nicely? Do you have any more pics? Sorry for al lthe questionsbut it's been an ambition of mine to do this for a while. Great to see you've done it!
-
It's in the normal position in lieu of the pen blade. I think the reflections in the photo make it look reversed
I'll have to take another photo of the blades closed later... -
Ah. That makes sense! It does look deceptive in the picture. Thanks again.

-
@Spork, Lord of Lime Jello! said:
@Spork, Lord of Lime Jello! said:
Finished this one with an inline awl. The awl had a broken tip, so I had to shorten it a little.
Also working on GAK rebuilds. Top row is all VIC with new blades except for one.
Bottom row are mix-and-match rebuilds of other brands...two Adlers, Aitor and a B&H. Still have a pile of them to work on...mostly ICARs
Lovely Spork! Out of interest (as I'm about to embark on a mod myself) did the awl drop in ok as it is?
Looking forward to pics of the Woodsmen - my fave SAK!
Spring tension is good...walks and talks. I was a little bit apprehensive because of the slightly larger pivot hole and the tang seeming to be a hair thicker, but it seems to work.
Ya I thought the same, but the slightly oversize hole didnt seem to matter. Vic does the same when they add the eblade and pruner to the xlt's and bigger ones.
Im sure I have extra new awls from 93s if anyone is needing any for mods. I did 93mm mods for years and lots of them had small blades or other in place of the awls, so I ended up with many spares.
-
Did you thin down the spacer under the blade tip since the awl is a bit thicker than small blade? I did this on the ones I built, but Im not convinced it was necessary.
-
-
Very nice!
-
Nice!
-
@hiraethus said:
Black and red Pioneer, with scissors added and pen blade in place of the can opener.


Hand made brass liners and small blade spacer. Note poor finish on edges of scale; thanks Victorinox. ::)Nice work! Did the pen blade drop right in place of the can opener with no mods? Is it one from a 91mm?
-
Thank you! Other than drilling the pivot to 3mm and bending the blade inwards to clear the cap lifter it's as standard on the 91mm knives.
-
@hiraethus said:
Thank you! Other than drilling the pivot to 3mm and bending the blade inwards to clear the cap lifter it's as standard on the 91mm knives.Could you describe how you go about bending a blade? I'm scared i'll snap it.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

