And so it begins.... (My adventures into Alox!)
-
Oh smurf yea!
-
It's really amazing to see the endless configurations that poeple want. Great job Syph.
What is your process for official orders? -
@Demel said:
It's really amazing to see the endless configurations that poeple want. Great job Syph.
What is your process for official orders?Yes, the funny this is, if it was up to me I would probably only build a few configurations. But Ive found that people really have different ideas about what a tool should have for them. So being flexible and providing as many options as possible is the main reason I think I still get alot of orders.
If you want a quote on something just shoot me a PM or email. I keep a list of orders and work on them in order. Im not running too far behind any more, probably 2-3 week lead time as long as Ive got the parts in stock. The nice thing about mostly doing Ti work is that it's easier for me to keep a stock of scales, and for donor SAKs I keep checking amazon or other places and order a bunch of donors when they go on sale.
I think the brass mag holders will work out nice, but the cost per part is creeping up and I haven't added the labor yet to do the finish work and tap for set screw. I only got 19 out of 6 square inches of brass. The cost for the brass + waterjet puts me at 9 bucks per part so far. Im going to finish one up in the morning and figure out how much labor is involved for finish work. The pieces are 0.125" thick and I have to shave them down to 0.110", then sand and polish and tap a 2-56 hole in there.
-
Not that we use the current plastic frames as prybars, but the sturdiness afforded by the brass, combined with the ability to replace the lens, will personally add a level of confidence in it's use that the plastic just doesn't give. Plus, the cool factor is just off the chart... :D
-
@Syph007 said:
I think the brass mag holders will work out nice, but the cost per part is creeping up and I haven't added the labor yet to do the finish work and tap for set screw. I only got 19 out of 6 square inches of brass. The cost for the brass + waterjet puts me at 9 bucks per part so far. Im going to finish one up in the morning and figure out how much labor is involved for finish work. The pieces are 0.125" thick and I have to shave them down to 0.110", then sand and polish and tap a 2-56 hole in there.Dangerous, I thought the one of your Ti models I got would be that "last knife I ever need"; but with the possibility of a brass lens- I'm weakening again.
-
First time poster here. Been lurking for a few months, checking in regularly following Syph007's work. Absolutely phenomenal ingenuity and craftsmanship.

-
@tankerG said:
First time poster here. Been lurking for a few months, checking in regularly following Syph007's work. Absolutely phenomenal ingenuity and craftsmanship.
Thanks for the kind words and welcome to the forum!
I'm working on the brass mag holders today. So far so good. I dont have an allen key small enough for the set screws I bought though, so I have to go hunting for smaller ones now.


-
Nice to see the progress, I'm looking forward to the end result.
-
I need a 0.035" wide hex key, which is smaller than all the local stores carry, so I had to order a precision set off amazon. Another thing I have to wait for.. but at least I have everything else I need and I just test fit the lens and its perfect.
-
First time poster here. Been lurking for a few months, checking in regularly following Syph007's work. Absolutely phenomenal ingenuity and craftsmanship. :2tu:
Thanks for the kind words and welcome to the forum!
I'm working on the brass mag holders today. So far so good. I dont have an allen key small enough for the set screws I bought though, so I have to go hunting for smaller ones now.


I know you like quality stuff so I highly suggest getting the Wiha brand. I have both sets and they are amazing.
I believe they sell them at Home Depot. If you cannot find those Bondhus is the next best in my opinion. They can also be found at Home Depot.
-
@Syph007 said:
I need a 0.035" wide hex key, which is smaller than all the local stores carry, so I had to order a precision set off amazon. Another thing I have to wait for.. but at least I have everything else I need and I just test fit the lens and its perfect.The Wiha metric set has one size under what you need as well. Goes down to 0.028.

I know you already ordered a different set, but just in case.
-
@captain spaulding said:
I need a 0.035" wide hex key, which is smaller than all the local stores carry, so I had to order a precision set off amazon. Another thing I have to wait for.. but at least I have everything else I need and I just test fit the lens and its perfect.
The Wiha metric set has one size under what you need as well. Goes down to 0.028.

I know you already ordered a different set, but just in case.
I checked lowes and home depot but they didnt have sets that went small enough. I might just go see if I can mill/grind a tiny drill bit or something to see if I can make a good nuff one for now just so I can get one finished.
Im sure more then a few people would go for a steampunk yeoman/explorer or similar. :D
-
@captain spaulding said:
I need a 0.035" wide hex key, which is smaller than all the local stores carry, so I had to order a precision set off amazon. Another thing I have to wait for.. but at least I have everything else I need and I just test fit the lens and its perfect.
The Wiha metric set has one size under what you need as well. Goes down to 0.028.

I know you already ordered a different set, but just in case.
I checked lowes and home depot but they didnt have sets that went small enough. I might just go see if I can mill/grind a tiny drill bit or something to see if I can make a good nuff one for now just so I can get one finished.
Im sure more then a few people would go for a steampunk yeoman/explorer or similar. :D
Indeed. Steampunk Yeoman would/will be an insta-hit!
-
@captain spaulding said:
I need a 0.035" wide hex key, which is smaller than all the local stores carry, so I had to order a precision set off amazon. Another thing I have to wait for.. but at least I have everything else I need and I just test fit the lens and its perfect.
The Wiha metric set has one size under what you need as well. Goes down to 0.028.

I know you already ordered a different set, but just in case.
I checked lowes and home depot but they didnt have sets that went small enough. I might just go see if I can mill/grind a tiny drill bit or something to see if I can make a good nuff one for now just so I can get one finished.
Im sure more then a few people would go for a steampunk yeoman/explorer or similar. :D
That's a bummer. My Home Depot has them unless I am not thinking correctly.

-
Success!!
I just ground a small bit I had to make do, and it worked ok to turn the set screw. I love this solution. The only thing I would add now is a tiny bit of rubber or similar in the hole so the screw isnt pushing on the glass directly but pushing a small plug of plastic or rubber.
Now of course I have to test is on an actual SAK, but Im optimistic it will work out just fine.









-
Mmm shiny... [emoji41]
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login



