Suggestions for a technicians multitool
-
Once again, I ask for the help of the community.
At the start of February, I started a new job, with an electronics retailer. I mostly deliver and install tv's, set-top boxes, washing machines, dryers, and similar.
It didn't take long for me to realize that my Suspension is just not fitted for this kind of work - I only use the blade (because it's one-handed and therefore convenient), the pliers, to hold nuts and bolts and the wire cutters, to cut coax cable and electrical cable.
Obviously, I've come to the conclusion that I need a new MT tofuel my addictionhelp me at work.I admit, I've got a soft spot for Leathermans, but as far as I can tell, none of their newer models with bit adapters, can take normal standard bits, which is a requirement.
My priorities are as follows:
Wire cutter, able to cut cleanly through coax cable (roughly 6-8 mm thick) as well as electrical cable.
One handed plain edge blade - as sheeple-friendly as possible.
Bit driver, that will accept standard 1/4" bits, preferably with magnetic retention.
Serrated blade would be nice, but not a requirement if the plain edge has decent edge-retention.Basically, I'm looking for something like the Surge or Charge, but with the ability to use standard bits, instead of Leathermans flattened bits.
Any thoughts? Am I looking for something that doesn't exist or have I overlooked the right tool several times and not noticed it?
EDIT: BTW, what do you call a guy like me, that installs everything from tv's to dryers, in english? Google Translate didn't exactly give me anything accurate...
-
The only one I know that takes standard bits is the Gerber MP-1
-
MP-1 or just get a charge. Those flat bits are really good. My work is on same line as yours and I carry TTi always and it works. Love the bits. And I absolutely need torx and hexagonal bits all the time. MP-1 is nice too. Good for a small mechanical work, also the pliers are springloaded in that one.
-
The Crunch has a standard quarter-inch hex bit driver, but not a OH blade.
I would recommend a Skeletool CX and deal with the squashed bits. Cutting clean through coax might be a bit much, but it can do the job in two bites. I own a regular Skele and I love it. Nothing wrong at all with the squashed bits.
There's also the CRKT Zilla. It's got a similar tool load to the Skeletool, and it takes regular quarter-inch bits. Can't vouch for it though since I don't own one.
-
So my doubts towards the capability of Leathermans flat bits, is really unfounded? I have a few multis with a 2 dimensional Philips and they suuuuuck. I always end up either using my SAK or getting a proper screwdriver. I'd say about 90% of the screws I encounter on a daily basis are Philips, and the rest are hex and torx - hence my need for a bit driver.
-
@Freaver said:
So my doubts towards the capability of Leathermans flat bits, is really unfounded? I have a few multis with a 2 dimensional Philips and they suuuuuck. I always end up either using my SAK or getting a proper screwdriver. I'd say about 90% of the screws I encounter on a daily basis are Philips, and the rest are hex and torx - hence my need for a bit driver.The problem is not the bits by itself, the problem is that you cannot replace individual bits if you break one (and that will happen sooner or later).
-
@Freaver said:
So my doubts towards the capability of Leathermans flat bits, is really unfounded? I have a few multis with a 2 dimensional Philips and they suuuuuck. I always end up either using my SAK or getting a proper screwdriver. I'd say about 90% of the screws I encounter on a daily basis are Philips, and the rest are hex and torx - hence my need for a bit driver.The Flattened bits are 3-Dimensional. Leatherman essentially just ground down the sides of standard 1/4" bits so that they take less space in their multi tools, while retaining the same utility.
If you plan on carrying bits around anyhow.... Leatherman sells a Bit Extender for the Wave/Charge/Surge series, which fits in the bit adapter, and takes standard bits as well as Leatherman's bits. There is also a version that fits on the 3D Phillips driver of the ST300/Rebar/Blast/Fuse/Kick.
-
+1 for the MP1

-
So my doubts towards the capability of Leathermans flat bits, is really unfounded? I have a few multis with a 2 dimensional Philips and they suuuuuck. I always end up either using my SAK or getting a proper screwdriver. I'd say about 90% of the screws I encounter on a daily basis are Philips, and the rest are hex and torx - hence my need for a bit driver.
The Flattened bits are 3-Dimensional. Leatherman essentially just ground down the sides of standard 1/4" bits so that they take less space in their multi tools, while retaining the same utility.
If you plan on carrying bits around anyhow.... Leatherman sells a Bit Extender for the Wave/Charge/Surge series, which fits in the bit adapter, and takes standard bits as well as Leatherman's bits. There is also a version that fits on the 3D Phillips driver of the ST300/Rebar/Blast/Fuse/Kick.
^^^ This. The bit extender is a great addition to the LM MTs with the bit adapter. Not only can you use standard 1/4 in bits but you get added reach as well. The LM bits are pretty good and I've found the shape and card they come in very handy to carry. Heck you get 42 bits in a neat tidy package.
-
Can I be honest?
If you rock up at my place to install a tv or dryer armed with a multitool only I'd ask you to leave. :D
No MT will ever have the ergonomics of a simple screwdriver.
If you're cutting coax you'll want to strip it, the I would want a good sidecutter.
I've done jobs like that, and I would want 4-8 various screwdrivers, 2 sizes sidecutters, large & small pliers depending on the task.
That's not a lot of tools, could easily be carried in a little bag, and saves a lot of swearing.:D You should have a MT on you anyway, just have the right tools for the job and use the correct parameters to choose the MT

-
@Gerhard Gerber said:
Can I be honest?If you rock up at my place to install a tv or dryer armed with a multitool only I'd ask you to leave. :D
No MT will ever have the ergonomics of a simple screwdriver.
If you're cutting coax you'll want to strip it, the I would want a good sidecutter.
I've done jobs like that, and I would want 4-8 various screwdrivers, 2 sizes sidecutters, large & small pliers depending on the task.
That's not a lot of tools, could easily be carried in a little bag, and saves a lot of swearing.:D You should have a MT on you anyway, just have the right tools for the job and use the correct parameters to choose the MT

Don't worry, I've got a toolbag with me as well. ;) It's just to be prepared and to have something on me, that can handle most situations.
So my doubts towards the capability of Leathermans flat bits, is really unfounded? I have a few multis with a 2 dimensional Philips and they suuuuuck. I always end up either using my SAK or getting a proper screwdriver. I'd say about 90% of the screws I encounter on a daily basis are Philips, and the rest are hex and torx - hence my need for a bit driver.
The Flattened bits are 3-Dimensional. Leatherman essentially just ground down the sides of standard 1/4" bits so that they take less space in their multi tools, while retaining the same utility.
If you plan on carrying bits around anyhow.... Leatherman sells a Bit Extender for the Wave/Charge/Surge series, which fits in the bit adapter, and takes standard bits as well as Leatherman's bits. There is also a version that fits on the 3D Phillips driver of the ST300/Rebar/Blast/Fuse/Kick.
^^^ This. The bit extender is a great addition to the LM MTs with the bit adapter. Not only can you use standard 1/4 in bits but you get added reach as well. The LM bits are pretty good and I've found the shape and card they come in very handy to carry. Heck you get 42 bits in a neat tidy package.
I'll look into that - might be the best option, with my love for LM.
-
I really doubted the Leatherman bits as well, but they really work. LM got the bite in those just right.
But Gerber MP-1 is really good too. I have a good quality Bosch bitkit with it and really like it. Those fullsize bits just take more space, with leatherman you can choose the bits you really need and they go with the same sheath as the tool. The reach is usually enough too.
If the devices you fix need huge reach, then it might not be enough.
-
I think these are your options:
Leatherman with bit extender: it also fits full size bits
Swisstool PLUS or sprit PLUS: these come with a ratchet and a set of full size bits
Gerber MP1: OHO sheeple friendly blade and built in full size bit accepting bit tool.
Victorinox Cybertool: does have a bit driver for full size bits and can also store full size bits, it might not be your first option because your'e an MT kind of guy (just like me
) but this tool is specifacly designed for electronic/computer work.
I advise you to carry it with a dedicated plier for cutting cable and coax cable. (it can cut 1 / 2 mm wire in a notch in the base of the pliers)
More info on SAK wiki page: http://www.sakwiki.com/tiki-index.php?page=CybertoolI don't think any of the MT's will cut coax cable and you should carry a dedicated plier for those tasks. Also cutting braided copper and steel wire with most MT's is a pain in the ass because it jams itself between the cutters and this jams the pliers


-
@anditsgone said:
I think these are your options:Leatherman with bit extender: it also fits full size bits
Swisstool PLUS or sprit PLUS: these come with a ratchet and a set of full size bits
Gerber MP1: OHO sheeple friendly blade and built in full size bit accepting bit tool.
Victorinox Cybertool: does have a bit driver for full size bits and can also store full size bits, it might not be your first option because your'e an MT kind of guy (just like me
) but this tool is specifacly designed for electronic/computer work.
I advise you to carry it with a dedicated plier for cutting cable and coax cable. (it can cut 1 / 2 mm wire in a notch in the base of the pliers)
More info on SAK wiki page: http://www.sakwiki.com/tiki-index.php?page=CybertoolI don't think any of the MT's will cut coax cable and you should carry a dedicated plier for those tasks. Also cutting braided copper and steel wire with most MT's is a pain in the ass because it jams itself between the cutters and this jams the pliers

I was under the impression that the Cybertool was using 3/16" bits and not the full sized 1/4" ones? That's not the case then?
-
I think these are your options:
Leatherman with bit extender: it also fits full size bits
Swisstool PLUS or sprit PLUS: these come with a ratchet and a set of full size bits
Gerber MP1: OHO sheeple friendly blade and built in full size bit accepting bit tool.
Victorinox Cybertool: does have a bit driver for full size bits and can also store full size bits, it might not be your first option because your'e an MT kind of guy (just like me
) but this tool is specifacly designed for electronic/computer work.
I advise you to carry it with a dedicated plier for cutting cable and coax cable. (it can cut 1 / 2 mm wire in a notch in the base of the pliers)
More info on SAK wiki page: http://www.sakwiki.com/tiki-index.php?page=CybertoolI don't think any of the MT's will cut coax cable and you should carry a dedicated plier for those tasks. Also cutting braided copper and steel wire with most MT's is a pain in the ass because it jams itself between the cutters and this jams the pliers

I was under the impression that the Cybertool was using 3/16" bits and not the full sized 1/4" ones? That's not the case then?
You are correct, they are 4mm bits.
-
@Etherealicer said:
I was under the impression that the Cybertool was using 3/16" bits and not the full sized 1/4" ones? That's not the case then?You are correct, they are 4mm bits.
[/quote]So it's even worse than 3/16"? Those I could go out and buy a couple of if they broke (or if I wanted shapes that wasn't included). 4mm? Not so much.
-
@Fortytwo said:
I was under the impression that the Cybertool was using 3/16" bits and not the full sized 1/4" ones? That's not the case then?
You are correct, they are 4mm bits.
So it's even worse than 3/16"? Those I could go out and buy a couple of if they broke (or if I wanted shapes that wasn't included). 4mm? Not so much.
All precision bits available here are 4mm

-
Sorry, i didn't know the cybertool uses special bits.
Thanks for correcting me. Would be a bummer if he bought it and the bits didn't fit. -
I have not tested it, but as the MP1 has anvil cutters, it might work better than the average MT with Bypass cutters?!
-
@lowtech said:
I have not tested it, but as the MP1 has anvil cutters, it might work better than the average MT with Bypass cutters?!The anvil style cutters will probably do a better job as the bypass cutters. The wingman and sidekick cutters also work great.
Although the do the job i am not a huge fan of the leatherman replaceable cutters. The stock wave pliers do a better job in my opinion and although i have abused those i never really had a problem with ruined cutting parts.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login