Suggestions for a technicians multitool
-
@anditsgone said:
I think these are your options:Leatherman with bit extender: it also fits full size bits
Swisstool PLUS or sprit PLUS: these come with a ratchet and a set of full size bits
Gerber MP1: OHO sheeple friendly blade and built in full size bit accepting bit tool.
Victorinox Cybertool: does have a bit driver for full size bits and can also store full size bits, it might not be your first option because your'e an MT kind of guy (just like me
) but this tool is specifacly designed for electronic/computer work.
I advise you to carry it with a dedicated plier for cutting cable and coax cable. (it can cut 1 / 2 mm wire in a notch in the base of the pliers)
More info on SAK wiki page: http://www.sakwiki.com/tiki-index.php?page=CybertoolI don't think any of the MT's will cut coax cable and you should carry a dedicated plier for those tasks. Also cutting braided copper and steel wire with most MT's is a pain in the ass because it jams itself between the cutters and this jams the pliers

I was under the impression that the Cybertool was using 3/16" bits and not the full sized 1/4" ones? That's not the case then?
-
I think these are your options:
Leatherman with bit extender: it also fits full size bits
Swisstool PLUS or sprit PLUS: these come with a ratchet and a set of full size bits
Gerber MP1: OHO sheeple friendly blade and built in full size bit accepting bit tool.
Victorinox Cybertool: does have a bit driver for full size bits and can also store full size bits, it might not be your first option because your'e an MT kind of guy (just like me
) but this tool is specifacly designed for electronic/computer work.
I advise you to carry it with a dedicated plier for cutting cable and coax cable. (it can cut 1 / 2 mm wire in a notch in the base of the pliers)
More info on SAK wiki page: http://www.sakwiki.com/tiki-index.php?page=CybertoolI don't think any of the MT's will cut coax cable and you should carry a dedicated plier for those tasks. Also cutting braided copper and steel wire with most MT's is a pain in the ass because it jams itself between the cutters and this jams the pliers

I was under the impression that the Cybertool was using 3/16" bits and not the full sized 1/4" ones? That's not the case then?
You are correct, they are 4mm bits.
-
@Etherealicer said:
I was under the impression that the Cybertool was using 3/16" bits and not the full sized 1/4" ones? That's not the case then?You are correct, they are 4mm bits.
[/quote]So it's even worse than 3/16"? Those I could go out and buy a couple of if they broke (or if I wanted shapes that wasn't included). 4mm? Not so much.
-
@Fortytwo said:
I was under the impression that the Cybertool was using 3/16" bits and not the full sized 1/4" ones? That's not the case then?
You are correct, they are 4mm bits.
So it's even worse than 3/16"? Those I could go out and buy a couple of if they broke (or if I wanted shapes that wasn't included). 4mm? Not so much.
All precision bits available here are 4mm

-
Sorry, i didn't know the cybertool uses special bits.
Thanks for correcting me. Would be a bummer if he bought it and the bits didn't fit. -
I have not tested it, but as the MP1 has anvil cutters, it might work better than the average MT with Bypass cutters?!
-
@lowtech said:
I have not tested it, but as the MP1 has anvil cutters, it might work better than the average MT with Bypass cutters?!The anvil style cutters will probably do a better job as the bypass cutters. The wingman and sidekick cutters also work great.
Although the do the job i am not a huge fan of the leatherman replaceable cutters. The stock wave pliers do a better job in my opinion and although i have abused those i never really had a problem with ruined cutting parts.
-
MP-1 has also off centered cutters right? Better for wires.
-
@Etherealicer said:
All precision bits available here are 4mm
That's not the case here, at least not the ones I have (small, cheap set). So there are a minimum of four sizes, 3 of them imperial (1/2", 1/4" & 3/16") plus 4mm too. We live and learn...

-
SOG powerplay has OHO blades, standard bit driver and a kickass shealth.
-
@Padre said:
I really doubted the Leatherman bits as well, but they really work. LM got the bite in those just right.But Gerber MP-1 is really good too. I have a good quality Bosch bitkit with it and really like it. Those fullsize bits just take more space, with leatherman you can choose the bits you really need and they go with the same sheath as the tool. The reach is usually enough too.
It's starting to look more and more like I should be getting a Leatherman. My only concern, was really the bits not gripping enough. Having the tool and bit kit in the same sheath is a huge plus, since I already carry more than enough stuff on my person.
@anditsgone said:
I think these are your options:Leatherman with bit extender: it also fits full size bits
Swisstool PLUS or sprit PLUS: these come with a ratchet and a set of full size bits
Gerber MP1: OHO sheeple friendly blade and built in full size bit accepting bit tool.
Victorinox Cybertool: does have a bit driver for full size bits and can also store full size bits, it might not be your first option because your'e an MT kind of guy (just like me
) but this tool is specifacly designed for electronic/computer work.
I advise you to carry it with a dedicated plier for cutting cable and coax cable. (it can cut 1 / 2 mm wire in a notch in the base of the pliers)
More info on SAK wiki page: http://www.sakwiki.com/tiki-index.php?page=CybertoolI don't think any of the MT's will cut coax cable and you should carry a dedicated plier for those tasks. Also cutting braided copper and steel wire with most MT's is a pain in the ass because it jams itself between the cutters and this jams the pliers

So far, the only thing that's making me consider the MP1, is the sheeple friendly blade. The flattened Leatherman bits might not be too easy to come by, if I lose them, compared to standard 1/4" bits, but I can still order them online and they take up less room.
As already mentioned, the Cybertool uses a weird size bits. A former colleague got one a while ago and I actually considered getting one, until I saw the bits - haven't seen them for sale anywhere and they seem rather easy to loose.
As far as cutting coax cable with a MT, I haven't had any problems doing it with my Suspension with anvil cutters. Every once in a while, a single thread doesn't get cut on the first try and then I just try again and it goes straight through.
If I carried a dedicated plier for cutting cable, I might as well not carry a MT and just rely on my SAK and a pair of pliers.@Padre said:
MP-1 has also off centered cutters right? Better for wires.You're right, they're off center just like on normal side cutters. Would be better for precision cutting.
@Kampfer said:
SOG powerplay has OHO blades, standard bit driver and a kickass shealth.I actually did consider SOG, especially their Reactor model, but after seeing your reactions to it, on facebook, I got kinda put off the whole idea with their bit driver. It is a nice sheath though.
Bottomline: I'm still in doubt.
The Gerber MP1 has the bonus of having offcenter cutters, making them a bit better for precision cutting, but the drawback being that the sheath (as far as I know), doesn't offer room for anything but the tool.
The Surge has room for the bit kit as well as accessories (perhaps a bit extender and a penlight), but the cutters are the bypass type, so it might not be to efficient with coax cable or electrical cable, for that matter.
Perhaps Wave is the way to go...sigh I'm confused... :ahhh
-
I pocket carry a CT on a regular base and I have never lost a bit.
I also glued a magnet into the bit-holder and now it takes all precision bits (Kraftwerk, Wiha, Wera etc...) but I think the CT is not for your line of work I think you are better off with standard 1/4".Personally, I would go for a Spirit Plus (+ additional bit kit), couple of screwdrivers, some pliers, side-cutter and a utility knife (perfect if you have to do some messier work also very people friendly).
The reason is actually simple... The Spirit has tools that the Wave lacks:- Awl
- Pry-Tool
- Chisel-Scraper
- Hook :D
I also prefer that you can use the bit-kit without the Spirit and due to standard bit size it can be combined with any bit-kit.
-
@Etherealicer said:
I pocket carry a CT on a regular base and I have never lost a bit.
I also glued a magnet into the bit-holder and now it takes all precision bits (Kraftwerk, Wiha, Wera etc...) but I think the CT is not for your line of work I think you are better off with standard 1/4".Personally, I would go for a Spirit Plus (+ additional bit kit), couple of screwdrivers, some pliers, side-cutter and a utility knife (perfect if you have to do some messier work also very people friendly).
The reason is actually simple... The Spirit has tools that the Wave lacks:- Awl
- Pry-Tool
- Chisel-Scraper
- Hook :D
I also prefer that you can use the bit-kit without the Spirit and due to standard bit size it can be combined with any bit-kit.
Your reasoning for the Spirit is lost on me - awl and hook are already on my Explorer in my pocket, if I need to pry I'll usually go for the bottle opener on the same Explorer and I very rarely need a scraper or chisel. ;)
As for precision bits, I carry a small pen-sized screwdriver with a small selection of bits in the handle. Come to think about it, I actually think they're the same size as the CT uses.
The whole idea was to minimize the amount of tools on me at one time - often I'll come in to a customers home, just to tweak some settings on their tv and the next moment I'm down on the floor, putting new connectors on their cables or trying to straighten bent pins in a connector. In a situation like that, I'd like to go in as "light" as possible, and still be able to do the task, without having to go back to the van and get my tools.
Hope that made sense. :) Basically, I'm lazy and don't like carrying full-size tools when I can avoid it. :D -
You really cannot go wrong with any tool you have thinked so far. I think the rest is just your own feel to it.
Go with your passion I'd say. Wave is probably the best tool for the money on the market right now, but you can always make it a bit lighter by spending extra money for Charge AL and getting that sweet 154CM knife.
And if spring loaded pliers and precision cutting (and the basic quarter inch socket) is a must, get MP-1, its really good too.Surge is quite heavy, I would close that one off.
-
I put in another vote for a Wave/Charge with the bit extender
The bit extender comes with the flat bits but you can use reg 1/4 inch bits as well :D The extender is a very nice addition just with the flat bits by themselves but with the ability to use reg bits in it sure does help 
-
I hate to say it, but a multi is a compromise. Get a good set of dedicated wire cutters and crimpers, and a utility knife. I'm also going to recommend a dedicated #2 philips and a 3/16" straight, or at least a decent 6-in-1 driver. Having hung enough routers and access points and humped plenty of wire, I really like a driver that is just a driver that can have some reach, and while I've done lots crimps with pliers they do sorta suck
And a good multitool, and bit driver or a bit holder that will let you use 1/4" bits with your 6-in-1.
I know you want minimalist, but there are times when the real thing is your best bet.
-
The Leatherman Crunch can use a bit driver. What about one of those, utility knife, some lineman pliers, wire strippers and a multi bit screwdriver?
-
@ironraven said:
I hate to say it, but a multi is a compromise. Get a good set of dedicated wire cutters and crimpers, and a utility knife.
[snip]
I know you want minimalist, but there are times when the real thing is your best bet.I feel you - as much as I'd like to do everything with a multitool, it just ain't happening. But I just want to be prepared - like I said earlier, sometimes I'll come into a customers home to maybe just adjust the tv and before I know it, I gotta cut zip-ties and shorten up their coax cable, because they're tired of having 10 feet of extra cable hanging behind their tv. And I'm lazy; if I can do it on the spot, with a tool that's already on my belt, I'm happy.
If I know beforehand that I'm gonna need tools, I'll bring them in the first time and have them ready.
One of my bosses actually came up to me yesterday with (what I would call) a 6-in-1 screwdriver. I think it holds 10 or 12 bits in the handle, standard 1/4". Again, if I know I'm gonna be needing a screwdriver, I'll bring that in with me. Between that and a good multitool, I'm usually pretty good covered.@ToolJoe said:
The Leatherman Crunch can use a bit driver. What about one of those, utility knife, some lineman pliers, wire strippers and a multi bit screwdriver?I've never liked the looks of the Crunch, to be honest. Besides, the blades are on the inside, which is a big no-no for me and it only has a serrated blade, no plain edge. Nonetheless, I'm thinking about it. The locking pliers could prove to be useful in quite a few situations.
So far, I'm going for the Wave - got bids on a few eBay-auctions at the moment, hopefully I'll get at least one of them. If not, I might look for a cheap Surge or Charge.
Thanks for all your tips guys.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login