New CRKT tool - the Bivy!
-
It's a great tool for someone who wants a very robust and quick-launching pliers and blade with a couple other tools. It's not dainty like other tools in its segment may be. If I was still doing oil-spill containment training on the river this would be my go-to tool.
-
How does those serrations work with ordinary cutting tasks?
I have a Liong Mah #6 with the same type of serrations, and I did not like them much. But I might be using it wrong.
-
I haven't used it enough yet to say. With aggressive serrations my experience would guess it's better for chopping through rope or cardboard or maybe small brush. It's going to tear very unevenly.
-
I have to say that I think I really like the look of this tool, and I can't wait to give it a shot. It does look a bit bulky though- maybe this is better suited to a bag rather than a pocket?
Def
-
I carried it yesterday in my front pocket with no trouble. It's thick, but it's short and smooth, so it didn't feel any bigger than a Wave in the pocket. I haven't tried it with tight jeans though.
I've found that if a pocket clip is attached to the center or left on the tool then the tool will settle in under the seam of the pants (in a right front pocket) instead of to the left of the seam with a right-side clip attachment. That allows your hand to more easily pass beside the tool into the pocket. When I realized this it made the center and left-side attachment point more logical to me on several tools like the Wingman/Sidekick and Signal. The Bivy is center-attached, so it sits under the seam just enough to benefit from this logic.
-
That's ok, my tight jeans days are well behind me....

I think I am going to have to grab one of these when I get back on my feet. I really do enjoy the out of the box thinking coming from the designers at CRKT, even if sometimes the results aren't the greatest.
Def
-
If they built it with plain stainless/ti handles and a little bit higher quality tools I'd like it a lot more.
-
The handles are aluminum with a good texture. The tools are actually really high quality to my experience. Have you tried one yet?
-
I had that issue with a few knives and tools over the years, and in many cases you really do get used to it after you put a few miles on a tool. The most prominent one in my mind (for me) was the Benchmade Panther. I really didn't like the square handle but eventually bought it simply because it was discontinued. After some use I found that I really liked it.
Def
-
@Grant Lamontagne said:
I had that issue with a few knives and tools over the years, and in many cases you really do get used to it after you put a few miles on a tool. The most prominent one in my mind (for me) was the Benchmade Panther. I really didn't like the square handle but eventually bought it simply because it was discontinued. After some use I found that I really liked it.Def
That Benchmade doesn't bother me. The handle's a little cheap looking but the blade looks alright.
-
Yah, that Benchmade doesn't bother me either.
-
The blade is gorgeous, but the handle (at first anyway) felt like I was holding a piece of Lego so I avoided it at first.
My point is, it's worth giving things a shot- it's hard to tell how you really feel about something until you've put it to work.
Def
-
Yeah, like the Leatherman Rebar's awl pisses me off when I deploy it then close the pliers.

-
Exactly. :D
Or how Leatherman advertises all of their one handed tools as being quick to deploy...... unless you are a lefty, in which case you don't matter. :P
Def
-
I have a Ka-Bar Dozier that looks like that Benchmade, and the handle is fine.

-
That looks pretty sweet actually. I think I may have to check it out.
Def
-
It's cheap can't remember where I bought it. It has a good blade. I liked the style of it too. You can get it with a thumbstud too, but I like the hole.
-
It can be had on the South American river for around 20-21. The thumbstudded version comes with a less acute tip and more colors.
-
I got mine from AG Russell for just a little more than that several years ago. When I carry a 3" folder it's usually that or a waved Spyderco or a CRKT M16.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login



