What's your latest SAK?
-
This trio of Wenger Commanders with Loctite and Permatex logos rolled in today. BNIB, it's obvious they've been on a shelf for a while from not only shelf wear and signs of aging on the boxes, the lube in them has yellowed and is a bit stiff. Will require some minimal cleaning and lubing. They're otherwise pristine.

These also have a
strange umbrellacrossbow logo on the tang.John
-
* Main blade is 2.4mm and tang has **umbrella** logo on (what would normally be) back side.I bet each time it rains he gets soaking wet... and the cops chase him!

Geez - and all this time I thought that umbrella is what kept the blades from rusting when they got wet!
-
Couple in today....
Airvac Blue Traveler and a Black EVO 14

-
Love them Robert!!! -
Couple in today....
Airvac Blue Traveler and a Black EVO 14

Nice set!
Thanks glen!!
-
@NetsNJ said:
Really digging this knife. Wish I had the Wenger version, but I'm really glad Vic kept some of the Wenger spirit going. Really comfortable knife, although the blade is misleading. The cutting edge of the blade isn't that much bigger than the Vic 111mm line. It is more comfortable and has a cooler lock mechanism though.I have the Vic EvoGrip 178 and like it very much. Mine is a bit stiffer to one-hand compared to the 111mm; may be the thumb hole size and location. Your remark about blade cutting edge length had me pulling it out and the 111mm OH GAK to compare them. Hadn't looked at the actual cutting edge before, which starts a little farther down the blade on the EvoGrip. My uncalibrated eyeballs tell me the EvoGrip's cutting edge is only about 1/4 inch longer. Didn't measure around the curve, as the GAK has a little more belly to the blade, which may reduce that a little more. I also like the EvoGrip lock a little better. I've gotten used to the liner lock on the 111mm and using it; may have been a little more difficult to use when the tab had a lower profile and none of mine have that older design.
John
-
Really digging this knife. Wish I had the Wenger version, but I'm really glad Vic kept some of the Wenger spirit going. Really comfortable knife, although the blade is misleading. The cutting edge of the blade isn't that much bigger than the Vic 111mm line. It is more comfortable and has a cooler lock mechanism though.
I believe Kam has what you are looking for

-
Old Armee Suisse-marked Fisherman with bail and pins.
-

Really digging this knife. Wish I had the Wenger version, but I'm really glad Vic kept some of the Wenger spirit going. Really comfortable knife, although the blade is misleading. The cutting edge of the blade isn't that much bigger than the Vic 111mm line. It is more comfortable and has a cooler lock mechanism though.
/topic/65246
I believe Kam has what you are looking for
/topic/65246
-
@kirk13 said:
Won either a Champion or a SwissChamp on an eBay auction earlier...for £16 delivered from Italy,I'm not too bothered which!Well,it arrived today!
Turns out it's a pre-hook,grooved cork screw Champion! Also turns out that the CS is utterly knackered,and the tip of the small blade is missing!

I'm deciding on restoration or modification!
-
That bites bro! :(
-
-
Won either a Champion or a SwissChamp on an eBay auction earlier...for £16 delivered from Italy,I'm not too bothered which!
Well,it arrived today!
Turns out it's a pre-hook,grooved cork screw Champion! Also turns out that the CS is utterly knackered,and the tip of the small blade is missing!

I'm deciding on restoration or modification!

-
This one just finished . . . a Waiter reincarnated as an Apprentice by replacing the corkscrew with a Phillips. Put the original nylon scales back on it and to get new ones for it as they're worn and nylon scales can't be restored very easily, if at all. The Vic logo is just about worn off.

This was my first "hack" and won't be my last, but there was a learning curve. Glad I started with something relatively straightforward and simpler with a corkscrew/Phillips swap. The organ donor was a small Tinker that had both its main and pen blades bent and badly nicked, plus the bottle opener was badly scratched and scuffed up. It had been thoroughly thrashed and trashed, but like most, the back side Phillips usually come out unscathed. It was 1992 or earlier as it has the sardine tin slot.
John
-
@jalind said:
This one just finished . . . a Waiter reincarnated as an Apprentice by replacing the corkscrew with a Phillips. Put the original nylon scales back on it and to get new ones for it as they're worn and nylon scales can't be restored very easily, if at all. The Vic logo is just about worn off.
This was my first "hack" and won't be my last, but there was a learning curve. Glad I started with something relatively straightforward and simpler with a corkscrew/Phillips swap. The organ donor was a small Tinker that had both its main and pen blades bent and badly nicked, plus the bottle opener was badly scratched and scuffed up. It had been thoroughly thrashed and trashed, but like most, the back side Phillips usually come out unscathed. It was 1992 or earlier as it has the sardine tin slot.
John
nice and worn scales are cool in my book
Sent from my iPhone using Tapatalk
-
I finally bought a SwissTool... then I decided to give it to my dad as he is ALWAYS doing something and always needs various tools. He was surprised, impressed with it and happy.

These SwissTools are awesome. That's what I call a tool.
-
This one just finished . . . a Waiter reincarnated as an Apprentice by replacing the corkscrew with a Phillips. Put the original nylon scales back on it and to get new ones for it as they're worn and nylon scales can't be restored very easily, if at all. The Vic logo is just about worn off.
This was my first "hack" and won't be my last, but there was a learning curve. Glad I started with something relatively straightforward and simpler with a corkscrew/Phillips swap. The organ donor was a small Tinker that had both its main and pen blades bent and badly nicked, plus the bottle opener was badly scratched and scuffed up. It had been thoroughly thrashed and trashed, but like most, the back side Phillips usually come out unscathed. It was 1992 or earlier as it has the sardine tin slot.
John
nice and worn scales are cool in my book
Sent from my iPhone using Tapatalk
Thanks. If they were Cellidor, fairly tight (having been reused) and in a condition to be restored some I'd probably keep them. Depending on how several more conversions turn out I may be giving this one to a good friend. If I do that with this one, it will undergo another deep cleaning and will definitely have new scales.
He commented recently that he always tries to keep a Tinker handy for the flat tip and Phillips combination, two tools he frequently uses, and the Small Tinker is the smallest SAK with a flat tip and (3-D) Phillips. I didn't say anything knowing my plans to do several Waiter --> Apprentice conversions, and thought I would drop an Apprentice on him as a surprise . . . with a reference to the SAKWiki.
John
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

