What did you use your Leatherman for today?
-
I used the file saw on the Rebar to cut the head off of a nail that came thru on one of my projects, the saw to do a quick cut on a 1x6, and the pliers to pull a bent nail.
-
I used my Crunch to pick up some trash outside of the house and also cut some fake flowers apart.
-
I used the Diesel's phillips driver a lot to assemble a bed for our little girl.
Sent from my SM-G920R4 using Tapatalk
-
@Alan K. said:
I used the Diesel's phillips driver a lot to assemble a bed for our little girl.
Sent from my SM-G920R4 using Tapatalk
Uh, Dude, you're in the Leatherman forum.

Haha, I thought it was the multitool one....oops

Sent from my SM-G920R4 using Tapatalk
I hope you were more careful assembling the bed.
-
I used my Crunch yesterday to pick up some trash outfront of the house and also cut some plastic flowers mrs tj was putting in an arrangement for one of her friends..
I showed her Mr. Crunch and it's capabilities and she gave a thumbs up.
-
@Alan K. said:
I used the Diesel's phillips driver a lot to assemble a bed for our little girl.
Sent from my SM-G920R4 using Tapatalk
Uh, Dude, you're in the Leatherman forum.

Haha, I thought it was the multitool one....oops

Sent from my SM-G920R4 using Tapatalk
I hope you were more careful assembling the bed.
Yeah, the bed turned out fine ;p
Sent from my SM-G920R4 using Tapatalk
-
I used the pliers on my Crunch to pull a strap through a buckle on my backpack.
-
Used my Supertool 200 to install a new LED under cabinet light over the sink this morning. Used the saw to cut a channel in the drywall for the wiring and the pliers and Phillips as well.
-
Wave helping me put up some cattle fence panels today.

-
I used my Rebar to help me and my youngest son build a Pinewood Derby car for tomorrow's race. The pliers worked great to align the axles! Went to get an alignment tool but the one we found was too narrow for the body. Leatherman (and the Evo 81 scissors) came thru again!
-
-
I used the blade on my Crunch to open up a taped up box of pasta to cook for dinner last night..
-
Used my Super Tool 300's Phillips driver to reattach some boards that had blown off the outside of the barn, and the awl to clean the dirt-caked screw head to allow the Phillips to fit inside the head.
-
I used the Signal's hammer to pound the padlock on our storage unit shut. It's the only way to do it as it's rusty.
Sent from my SM-G920R4 using Tapatalk
-
I cut the damaged wheel well out of a crashed car with the blade of the PST. A piece of plastic held it to the frame and kept the wheel from turning freely. "I have a Leatherman....I can help!" really paid off this time!
-
I used the serrated blade on my ST300 to cut a piece of starter rope to fix a cut-off saw today and cut the tape on the bottom of a box so I could compact it down and throw it away

-
I used the screwdriver on the Micra to tighten a screw in an old wooden bank we have.
-
I will spend hundreds of dollars for a good knife but I'm too cheap to spend $50.00 for a hose.LOL
I replaced the female end of the hose last week and today I replaced the male end.I used my ever trusty Leatherman Wave to accomplish this minor repair.The serrated blade worked well to cut the old hose in preparation for the installation of the of the male mender device.I then relied upon the flat blade screwdriver to attach the collar that holds the new part in place.
A job well done Leatherman.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
