Another hack for the Leatherman knurled screws.
-
Welcome to the forum Goldmeister
And good idea with the plant stand tools
:D -
Yet another solution. Having made the previously posted tools to disassemble the Micra, I started thinking that there might be people who wanted to be proactive with their Leatherman tools, but didn't have access to appropriate scrap metal, a shop with a piercing saw, flex shaft, drill press, bench grinder, etc. Soooo, for folks who may not have access to anything more than a hammer, try an old house or car key. I found a couple of old car keys with round holes that were just the right size for a Micra. All you need is a hammer, but failing that, a medium size rock will do the trick. You can then contour the key so you get clearance at the scissor end by rubbing it on the sidewalk or the rock you used for a hammer. In computer lingo, that would be a "kludge" (an inelegant, but workable solution) or in military terms, a "field expedient". Giving credit where it's due, this was all inspired by Spoonrobot.
Goldmeister
-
Welcome to the forum Goldmeister!
Wow, you jumped right in and hit the ground running with some great suggestions! The key idea is particularly intriguing.....being made from brass, they would certainly take the knurled form easier when you hammer them into place. But is the brass itself too soft to act as a wrench? Will it simply spin and wash out the knurled teeth when used on a tight screw? 
-
Thanks for the welcome Poncho65. Nice forum you have here with a bunch of interesting and really talented tool guys/gals.
Forgot to add a note to those who are advocating heat to loosen the Loc-Tite. 350-400 degrees F is a little dicey on hardened and tempered steel. For one thing, it's hard to be that precise with a torch, heat gun or big soldering iron and unless you know exactly how the steel was heat treated, and even though stainless is a terrible heat conductor, it's hard to keep it localized and there's a good chance it will further draw the temper on the edged components.
Goldmeister
-
Thanks for the welcome J-sews.
Keys, even though made of brass, are pretty hard. Think about how long they last rubbing on the pins in locks and how much torque they take day in and day out. I saw a TV show on the making of keys a while back and, as I remember, they're a hard alloy and are stamped with a great deal of pressure which work hardens them. Before I posted, I tested them and they worked fine. Don't forget that there are a whole lotta contact points so the stress is well distributed. As far as the long term, I'll use hell out of them and report back.By the by, according to Kwakster, you seem to be the guy who has the line on the cool factory made tools. Is that true?
Goldmeister
-
@Goldmeister said:
Thanks for the welcome J-sews.
Keys, even though made of brass, are pretty hard. Think about how long they last rubbing on the pins in locks and how much torque they take day in and day out. I saw a TV show on the making of keys a while back and, as I remember, they're a hard alloy and are stamped with a great deal of pressure which work hardens them. Before I posted, I tested them and they worked fine. Don't forget that there are a whole lotta contact points so the stress is well distributed. As far as the long term, I'll use hell out of them and report back.By the by, according to Kwakster, you seem to be the guy who has the line on the cool factory made tools. Is that true?
Goldmeister
Good points about the keys, that makes sense :)
Yah, I'm the American liason for the Leatherman factory tools. (Tarrodemierda handles the European modders) They are on the way to a certain culinary oriented member in Alabama, then probably heading to the east coast. It might be a little while before they are actually available again, but I'll put your name on the list. :)
(check your PM's by the way)
-
:ahhh That key idea is great as well I might have 2 try that 1 for myself

-
Great posts Goldy , those damned knurled screws have been occupying my mind a lot longer than any fastener has a right too. I liked the Spoony sockets but balk at the whacking socket on the tool , I worry about damaging the tool surface around the fastener. I was wondering if you heated the socket's end to make it softer if it would take the knurled profile easier ( It would be handy to have spare knurled fasteners to do this) . I was also wondering if you could make a hard wood tool to get the job done . Goldy if you ever do the key mod please show us , I am interested in a tool for the larger knurled fasteners. Great work mate.

-
Updated report on using keys: I tried them on three Micras that had never been taken apart. Got five screws open, but stripped one key on the sixth which was particularly non-cooperative. As I stated in the original post, it's a field expedient for someone who has no other option and needs to get one apart and together one time. I believe if handled carefully, a pair of keys will work, but should not be considered as long term service tools.
Goldmeister
-
Multimat,
I just posted the results on the keys; good for one Micra, one time. The key deal is pretty simple. Just find an old one with a round hole in it. I happened to luck out and find a couple with approx. 5.0mm. holes and hammered them on to the knurled screw. For a larger screw, if you can't find an appropriate key, you may have to take a rat tail file to the hole to open it up a bit. Will get a picture of it up.
I'm working on experimenting with various items found in the average household or available for cheap in the local hardware store. No way wood will work and I think a low quality socket would work pretty well. Those stainless screws are harder than the hinges of hell and if you don't use the same ones over and over, I think you could imprint mild steel very effectively without trashing them.
My next experiment may be a piece of hacksaw blade which would have to be normalized first as they're hardened. Average person should be able to do it over a kitchen stove.
I'm also thinking of some way to use a hex nut of the appropriate size. You'd have to grind one end of it down to get past the counter sink and into the threads and then just hammer it on to the knurled screw, imprint it and then grind the tips off so it becomes a tube, more or less. Get the appropriate sized hex head bolt, put some red Loc-tite or epoxy on it and thread it into the other end of the nut . Then you could get a wrench on the head of the bolt. Obviously, you'd need two of them.
Just thinking out loud here so don't take either of these as fact. I feel the same way you do about the amount of time these knurled screws took to figure out without the factory tools. I've always maintained that EVERYTHING comes apart without destroying it given enough well directed thought. I remember spending several days trying to get the sprocket off the rear wheel of a three speed bike and finally discovering it was a left hand thread. That was about thirty years ago and I've never forgotten how stupid I felt and how important thought is before using brute force.
Goldmeister
-
Thanks buddy , it would be good if you post pics of your Key tool

-
All good ideas so far Goldmeister!
Sounds like you are focusing on the Micra so far. It uses the smallest of the Leatherman knurled screws. You're new here, maybe you were not aware that on the medium-size knurled screw, a pair of Kick pocket clips makes the ideal set of wrenchs. :)
(I wish they sold a pocket clip for the Micra!) ;)
-
Welcome to the forum mate :)
-
Multimat,
Here ya go. Pictures aren't great, but you get the idea.
J-Sews,
Yep, I'm aware of the Kick pocket clips for the larger sizes. May even have seen them here. Found them for under $1.50/each and got two in my shopping cart. When I checked out, I found they wanted something like $12 for shipping. I registered my displeasure by canceling the order.
Goldmeister


-
Mickey d,
Thanks for the welcome. Judging by your number of posts, it looks like you've been around since the very beginning. Having been called Mate by two different members in a space of a few hours, would it be safe to assume there's a contingent from OZ and/or the UK? Always good company and a match for "Yankee Ingenuity" any day!
Goldmeister
-
@Goldmeister said:
Mickey d,Thanks for the welcome. Judging by your number of posts, it looks like you've been around since the very beginning. Having been called Mate by two different members in a space of a few hours, would it be safe to assume there's a contingent from OZ and/or the UK? Always good company and a match for "Yankee Ingenuity" any day!
Goldmeister
A large portion of this forum's members are from the UK.
And others, like me, aren't, but have picked up some of their habits...
-
@One Lame Frog said:
Mickey d,
Thanks for the welcome. Judging by your number of posts, it looks like you've been around since the very beginning. Having been called Mate by two different members in a space of a few hours, would it be safe to assume there's a contingent from OZ and/or the UK? Always good company and a match for "Yankee Ingenuity" any day!
Goldmeister
A large portion of this forum's members are from the UK.
And others, like me, aren't, but have picked up some of their habits...
There does seem to be quite a few of us now.
Great suggestions Goldmeister, and again, welcome to the forum. :)
-
@One Lame Frog said:
Mickey d,
Thanks for the welcome. Judging by your number of posts, it looks like you've been around since the very beginning. Having been called Mate by two different members in a space of a few hours, would it be safe to assume there's a contingent from OZ and/or the UK? Always good company and a match for "Yankee Ingenuity" any day!
Goldmeister
A large portion of this forum's members are from the UK.
And others, like me, aren't, but have picked up some of their habits...
Yeah, one of their habits is the way they take a thread off-topic. They do this constantly. I'm proud to say that I never do that. :)
-
Been working on this since the last post and finally have the $.90 tool for knurled screws on Leatherman Micra, PST and anything else that uses knurled screws of the appropriate sizes. I was lurking around the fastener section of my local hardware store hoping for divine inspiration and I got it: 3/16" coupling nuts. First I normalized it (made the steel as soft as possible), drilled a 5mm. hole in one end about 3/32" deep and then turned it around and drilled a 1/4" hole on the other end to the same depth. Smacked the 5mm. end down on a Micra knurled screw, turned it over and smacked the 1/4" end down on a PST knurled screw. Filed the ends true and tested it out. Combined it with one of the previously posted flat iron type wrenches and it worked great. You can grab the coupling nut with a 5/16" socket, open end wrench or whatever. Got so much torque that when I was tightening the screws on a Micra, I sheared one of the scissor end screws. If anyone has a spare, I'd be happy to tender coin of the appropriate realm for said screw and postage.
Goldmeister

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login