Let's see your sharpening stones/gear!
-
@Fortytwo said:
I'm currently out travelling Europe for a month but realised I wanted sharp knives. Luckily I found this second hand steel for 2$ a short while before leaving. It was made by EKA in Sweden and really small as seen by comparing it with a Spartan. Just what suited my needs (it's not like I will have to do any reprofiling out anything).That's a great travel solution!!!!

-
I've got the usual, vic ceramic, lansky 4 rod turn box and a lansky puck (which I don't like).
The new one to me is this and I'm waiting to have a day free when I can set it up and learn how to use it properly.

Sent from my iPhone using Tapatalk
-
That's a nice one Smashie!!!! I could never do the guided ones, too impatient. I have a lansky puck as well for machetes and lawnmower blades.
-
Thanks. I'm going to give this its first outing on a tramontina machete and see what can be done
Sent from my iPhone using Tapatalk
-
I will, I've just got to pick up a stable base to put it on
Sent from my iPhone using Tapatalk
-
I have quite a few different ones that I use.
Lansky 3 stone kit with added S1000 Ultra fine stone.
Lansky 4 rod turn box.
DMT Aligner kit with the standard three stones (course, fine and x-fine stones) and added x-course stone.
Worksharp Field Sharpener.
and two sets of the Spyderco 701MF profile set as well as a Sharpmaker with stock med and fine rods.



-
I used to free hand on a three stone system. One of those 8” triangular blocks that sat in a base but I haven't used it in years.
The knives I use now won't sharpen much less re-profile with wet stones.
So I've switched to a KME diamond system, It works with smaller blades better than some of the more expensive systems.I have 140, 300, 600, 1500 grit diamonds, I made a couple strops to fit into it. I clamp it in the bench vice to use it.
Once I have the profile set and it's sharp, I just use the larger bench strop to maintain the edge and don't use the system much at all.
The funny thing or maybe it's the sad thing but I spent more on the KME system than my first D2 steel knife.

-
@sir_mike said:
I have quite a few different ones that I use.Lansky 3 stone kit with added S1000 Ultra fine stone.
Lansky 4 rod turn box.
DMT Aligner kit with the standard three stones (course, fine and x-fine stones) and added x-course stone.
Worksharp Field Sharpener.
and two sets of the Spyderco 701MF profile set as well as a Sharpmaker with stock med and fine rods.Hey Mike are the 701 MF about the same as using the triangle stones of the Sharpmaker free hand

-

Plus a few other DMT's.
-
I have quite a few different ones that I use.
Lansky 3 stone kit with added S1000 Ultra fine stone.
Lansky 4 rod turn box.
DMT Aligner kit with the standard three stones (course, fine and x-fine stones) and added x-course stone.
Worksharp Field Sharpener.
and two sets of the Spyderco 701MF profile set as well as a Sharpmaker with stock med and fine rods.Hey Mike are the 701 MF about the same as using the triangle stones of the Sharpmaker free hand

I would say they maybe similar but the 701's will lay flat and they are longer so to me they are easier to use.
-
@sir_mike said:
I have quite a few different ones that I use.Lansky 3 stone kit with added S1000 Ultra fine stone.
Lansky 4 rod turn box.
DMT Aligner kit with the standard three stones (course, fine and x-fine stones) and added x-course stone.
Worksharp Field Sharpener.
and two sets of the Spyderco 701MF profile set as well as a Sharpmaker with stock med and fine rods.Great gear Mike!!! Which one is your "go to first" when an edge needs work? Your fav?
-
@Dean51 said:
I used to free hand on a three stone system. One of those 8” triangular blocks that sat in a base but I haven't used it in years.The knives I use now won't sharpen much less re-profile with wet stones.
So I've switched to a KME diamond system, It works with smaller blades better than some of the more expensive systems.I have 140, 300, 600, 1500 grit diamonds, I made a couple strops to fit into it. I clamp it in the bench vice to use it.
Once I have the profile set and it's sharp, I just use the larger bench strop to maintain the edge and don't use the system much at all.
The funny thing or maybe it's the sad thing but I spent more on the KME system than my first D2 steel knife.
That's a very complete set!
Sounds like it works great!!!! -
I have quite a few different ones that I use.
Lansky 3 stone kit with added S1000 Ultra fine stone.
Lansky 4 rod turn box.
DMT Aligner kit with the standard three stones (course, fine and x-fine stones) and added x-course stone.
Worksharp Field Sharpener.
and two sets of the Spyderco 701MF profile set as well as a Sharpmaker with stock med and fine rods.Hey Mike are the 701 MF about the same as using the triangle stones of the Sharpmaker free hand

I would say they maybe similar but the 701's will lay flat and they are longer so to me they are easier to use.
Thanks
I have eyeballed those since Kwakster had a set way back when on here 
-
@Brock O Lee said:

Plus a few other DMT's.
Another great setup!!!! Brock, how big a big a blade can you sharpen on that rig, 8", 10"?
Thanks SAK Guy. The largest knife I've sharpened on the Edge Pro is our chef's knife, which is around 10". It is probably the practical limit, but in theory the EP can handle any length blade.
These days I often sharpen freehand using a DMT diasharp benchstone, DMT diafolds or the EP stones.
-
I used to free hand on a three stone system. One of those 8” triangular blocks that sat in a base but I haven't used it in years.
The knives I use now won't sharpen much less re-profile with wet stones.
So I've switched to a KME diamond system, It works with smaller blades better than some of the more expensive systems.I have 140, 300, 600, 1500 grit diamonds, I made a couple strops to fit into it. I clamp it in the bench vice to use it.
Once I have the profile set and it's sharp, I just use the larger bench strop to maintain the edge and don't use the system much at all.
The funny thing or maybe it's the sad thing but I spent more on the KME system than my first D2 steel knife.
That's a very complete set!
Sounds like it works great!!!!Thanks
It works great on slip joint style and small to medium fixed blades. So for me it is perfect.The Kabar Mark 1 is about the longest fixed blade i would recommend using the KME on. It rotates and locks on a spring detent so there is a limit to how much weight you could hang on it.
It's really not made for the thick (1/4") blades either. -
@Brock O Lee said:
@Brock O Lee said:

Plus a few other DMT's.
Another great setup!!!! Brock, how big a big a blade can you sharpen on that rig, 8", 10"?
Thanks SAK Guy. The largest knife I've sharpened on the Edge Pro is our chef's knife, which is around 10". It is probably the practical limit, but in theory the EP can handle any length blade.
These days I often sharpen freehand using a DMT diasharp benchstone, DMT diafolds or the EP stones.
Looking at reviews, the DMT stones look great...if I ever upgrade my Smiths, those are my choice! 
-
I used to free hand on a three stone system. One of those 8” triangular blocks that sat in a base but I haven't used it in years.
The knives I use now won't sharpen much less re-profile with wet stones.
So I've switched to a KME diamond system, It works with smaller blades better than some of the more expensive systems.I have 140, 300, 600, 1500 grit diamonds, I made a couple strops to fit into it. I clamp it in the bench vice to use it.
Once I have the profile set and it's sharp, I just use the larger bench strop to maintain the edge and don't use the system much at all.
The funny thing or maybe it's the sad thing but I spent more on the KME system than my first D2 steel knife.
That's a very complete set!
Sounds like it works great!!!!Thanks
It works great on slip joint style and small to medium fixed blades. So for me it is perfect.The Kabar Mark 1 is about the longest fixed blade i would recommend using the KME on. It rotates and locks on a spring detent so there is a limit to how much weight you could hang on it.
It's really not made for the thick (1/4") blades either.
Good info!!! That's the kind of "hands on" report you don't get in the product description!!! If I went with a guided setup, probably couldn't use that one on my Bowies and bigger Beckers. Thank you! 
-
I have quite a few different ones that I use.
Lansky 3 stone kit with added S1000 Ultra fine stone.
Lansky 4 rod turn box.
DMT Aligner kit with the standard three stones (course, fine and x-fine stones) and added x-course stone.
Worksharp Field Sharpener.
and two sets of the Spyderco 701MF profile set as well as a Sharpmaker with stock med and fine rods.Great gear Mike!!! Which one is your "go to first" when an edge needs work? Your fav?
I usually just grab the Sharpmaker (not pictured) when I need a touchup. If I need more than that, I grab the DMT Aligner kit or Lansky guided (just sitting on my bench so already out). Since I have this much and don't use my blades too much, I was trying to downsize cause some are basically duplicates and sell of the Lansky guided and turn box ones. I am not sure if I posted them for sale here or not but I did in other places! :)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login