Awls and Chisels for LM Charge, Wave, Surge
-
Sorry if this has been suggested already but would it not be possible to grind the awl on one side and the chisel on the other so that its reversible like the other bits?
It would indeed be possible (and I will admit that this idea never occurred to me either) but I don't think it would be a good idea. In use, both the awl and the chisel would be "pushed on" hard, causing the other end of the bit to bottom out in the receptacle. If that other end were a sharp awl or chisel, it would probably become dull or damaged.
Unless you could have a tool on the other end which wouldnt matter if it was pressed on .. say a spare flat point driver or erm ..??? I dont know but there must be some.
-
Yeah, I had this exact idea Thargor, but the reason why it isnt a good idea as pointed out by Bob is what the necessary conclusion if when you think about how you would use the tools.
I like the idea of having something on the other side, even if a screwriver type bit, but I don't see it as necessary, especially since it would involve a lot more work on the part of a manufacturer who doesnt do this for a living (i.e. Bob, as opposed to Leatherman). Therefore if it can be done it would be a bonus (can't really think of a disadvantage), but if not, the bits as they are look stunning.
What I've been trying to wrack my brains about are two more possible tools that could be made in this form. The reason being, the bit sheath provided with charge models has 4 empty slots. If two are taken up by a chisel and awl, if the other two could be filled by two more useful tools it would fill the sheath and I think that'd be quite neat.
Cannot think of anything at the moment though ??? Anyone have any sensible ideas?
-
What about a tool similar to that used by people who sew to cut threads, so it has two points (one could be blunt, one sharp?) with a sharp edge inbetween, like I have tried to how with paint below.
Such a tool I feel could be used as a 'reverse' cutting hook (so cutting by pushing forward rather than pulling back), so especially useful on the LMs without their standard cutting hook. I havent thought of any other uses for it.
-
And what about this: a wire stripper which is basically a bit with holes in it. I have no idea if this is feasible or practical, just thought i'd throw the idea forward. I've tried to show two alternatives in the paint picture I've made.
-
Here's a silly idea- since Leatherman's combo tool works better as a dedicated can opener due to the sharp point, what about a bottle opener notch in the side?
Def
-
I just happened to have a beer handy so I used my Wave to open it, and well, you can see the results.
Def
-
@Raukodur said:
What about a tool similar to that used by people who sew to cut threads, so it has two points (one could be blunt, one sharp?) with a sharp edge inbetween, like I have tried to how with paint below.Such a tool I feel could be used as a 'reverse' cutting hook (so cutting by pushing forward rather than pulling back), so especially useful on the LMs without their standard cutting hook. I havent thought of any other uses for it.
Would this tool just do the same type of work as the hook on the backside of your serrated knife blade?
-
Thats the problem, I cant figure out another use for it. However, on the surge and wave, and charge models that dont have a cutting hook, wouldnt it be a useful function to have? I think a hook is preferable since the pulling motion is better for this type of cutting than pushing, but can't having pulling on a bit otherwise itd come out of the driver.
-
Now if you could make a five point security torx bit easy enough to sell them on here. I bet that would get your Karma points well up. >:D >:D
Dave
-
@Defender said:
I just happened to have a beer handy so I used my Wave to open it, and well, you can see the results.Gotta work on yer technique there, Def ol' boy!

I couldn't count how many bottles of beer I've opened with the combo tool on my original PST or old-skool Wave (plus Wenger SAKs, BuckTools, Gerbers, etc.). It's not that hard.
First of all, once you hook the rim of the cap, twist the tool a bit so that the sharp tip of the opener is near the rim, not in the soft middle of the cap. Also, lift up firmly, rather than "lever" the tool at the rim. That works well for a dedicated bottle opener implement, but with the combo, some allowances must be made. It still beats opening 'em with yer teeth!

-
One very important thing you have to do Bob, is give the awl and chisel a test in the leatherman, and tell us how they work! Lets hope they perform well enough to be used on a regular basis.
-
@Raukodur said:
One very important thing you have to do Bob, is give the awl and chisel a test in the leatherman, and tell us how they work! Lets hope they perform well enough to be used on a regular basis.I have not yet used the awl, but the chisel works well enough. Messing around with a piece of scrap wood, I was able to shave up some mighty fine splinters. ;) Surprisingly, it seems that the chisel works better "upside down" from how I had first imagined. (see picture below)
If used as shown in the upper sketch, the chisel seemed to dive into the wood and get stuck.
If used as shown in the lower sketch, it would roll up a nice splinter of wood, with no diving in.

-
Now all I need is a legitimate use for it, instead of just making random gouges in a piece of wood. The Vic SwissTool and Vic Spirit both have chisel blades. What do people use them for?
-
If you really wanted a chisel on a Leatherman (I dont really, I havent had the need for a chisel since woodwork class in school) wouldnt it be possible to grind the large screwdrivers tip into a shape like this?:
So its a combination large screwdriber/chisel like the combination bottle/can opener? It would still open screws okay I reckon. A bit extreme though maybe...
-
I must confess, I don't often have a need for a chisel/scraper either. But both the Victorinox SwissTool and the Spirit have a scraper blade, so I assume some folks must have a regular need for one. I suppose the large screwdriver could be sharpened up and do double-duty as a scraper. It seems like using it in the screwdriver mode might dull or damage the sharp chisel edge though?
-
Yeah, wouldnt really want to use a sharp edge to open screws, on tough screwes youd be likely to twist the metal I think and wreck your scewdriver and chisel.
So Bob, I am feeling a desperate need to own a chisel and awl bit for my charge, but realise they are preproduction atm

If more people are interested in them for their LMs aswell, would you consider creating, selling and shipping them? The thought of adding two more functions to my multitool without compromising anything is quite exciting. Especially since both bits would fit so neatly into the bit sheath.
-
Well Raukodur, since this was all mostly your idea anyhow, how about if I just send you a pair of "pre-production samples"? :) (Y'know, for field testing trials and such, just like the big manufacturers do.) :D
-
Well now Bob, that would be mighty generous of you :) I would highly appreciate that!
When you get around to it, if you tell me the transatlantic shipping fee I will transfer it to your account.
-
One Meeelion dollars!

Def
-
Anyone got any ideas for another tool which could be made to fit in the bit driver (i.e. a tool that functiosn by being pushed or twisted, not pulled, or bent)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login