Contender 1- BLACK UTILITY POCKET KNIFE BOX CUTTER BOTTLE OPENER SCREWDRIVER EDC
-
All I can say, my copy is well made and useful. I haven't had any issues with it yet. For the price, these are a steal.
-
-
I picked up one of these a couple years back when they first hit the Pacific Rim vendors. My take: it's a cleverly designed piece of junk.
I like its size, its flatness, the multi functionality.
I dislike the blade holding/retention method. First, the blade lock is sort of a frame lock kind of implementation. Bending the tab on the bottle opener half of the body allows the blade to slide into position, and also be removed.
Problem one: the "frame lock" tab is tight, kind of fiddly, and small.
Problem two: this is very much a two hand opening (retracting/extending) knife. One has to open the "frame lock", and then manipulate the blade with the other hand into proper position. Either engage one of the notches on the top of the blade, or the end of the blade in the case of full retraction. There are no visual cues to know when this happens. There are tactile cues... sort of.
Leading to problem three: the "frame lock" not only keeps the blade from extending/retracting, it also keeps the blade in its very thin cavity. Releasing the "frame lock" just as easily allows the blade to move vertically as well as in and out. It can be hard to tell if the blade has come out of its track without good inspection. Leading to insecure blade retention.
Problem three, the blade cavity track is nothing more than a shallow channel machined in the bottle opener half of the handle. The blade edge floats around in there, riding against the steel side of the channel. For its whole length. A steel edge riding against steel leads to a pre-dulled edge before you ever even use it. Call me a stickler, but the reason to carry a razor blade knife is to have something that can be relied on to be pretty sharp, without a rolled edge.
It is a rather handsome looking widget, to be sure. It's simply two halves held together with three small phillips screws, all three heads stripped out during installing. Perhaps a cheap attempt at tamper proofing? ;)
So, yeah, no one hand opening, no easy two handed opening for that matter, edge killing design, make for a useless tool IMO.
-
Good points indeed. To be honest I haven't given a lot of thought to the actual operation of this tool as I was waiting for it to come in to see.
I will definitely make note of your post as it sounds like this could be potentially hazardous to fingers.
Def
-
Just in case you feel that $5 is an unfair price for this tool:
Def
-
@Grant Lamontagne said:
Just in case you feel that $5 is an unfair price for this tool:Def
That damascus utility blade will go nicely with my 1,000 thread count toilet paper.
-
Holy crap, how much? :o
-
-
:o

Yeah, 5 bucks is sounding a lot better. I think I found mine for 3 dollars last year off of eBay.
-
Contender 1 arrived today and I'm not sure what, if anything I was expecting, although a part of me thinks it's cool that Contender 1 arrived first. :D

The first thing I noticed was that it was much larger than I expected it to be. I expected it to be about half to two thirds of the size that it is, but as you can see it is somewhat larger than a 91mm SAK, which of course is what made me decide to take my own measurements. Out came the calipers and my results are as follows:




100mm long
26mm high
3mm thick
34 gramsNow that that is out of the way, Contender 1 came with three blades- one installed in the tool and two more in a plastic baggie, which is good, because when it comes to securing razor blades we all know the plastic baggie is near the top of safe handling and containment materials.


On the surface, this seems like it might be an ok tool- after all, it's just a razor blade holder with a bottle opener and screwdriver on the end. Well, I haven't actually used it yet, as I've just opened the package and took some pics, but I have to say that I am thoroughly unimpressed so far.

As mentioned above the razor blade is drawn over and then pressed against the screw on the corner that holds the two halves of the frame together. Not only does this dull the edge but it also chips it off, as you can see from the above photo- if a bit of rough handling in a bubble mailer can leave giant marks in the blade, what are the chances it will be in any shape to be used when it's been bounced around in a first aid kit or EDC bag?

The next issue with this tool is that you sort of have to pry the halves apart enough that you can lift the blade over the screw and out the opening so that it can be used. I have fairly small, almost ladylike hands, and this was not easy for me to accomplish, so those of you that have man sized hands are pretty well screwed, and you'll probably need a multitool with you to get the blade out.

Then, once you have the blade sticking out, the next bit of fun begins- the blade won't come out any further which is nice, but there's nothing but the most basic amount of friction to keep it from sliding back in. On the surface that sounds ok, but in reality that will probably get annoying in actual use, especially if it can't be then extended again easily.

I'm going to give this one some use and see what happens, but I have to say I am not expecting much from this tool. If this was the end of the Challenge and not the first look I'd have to say this one fails miserably, but there's still time for it to redeem itself. You never know, it might perform a lot better in actual use. I am hoping so, because this tool is remarkably disappointing at this point.

Def
-
Strange that there's no real retention of the blade, I would have thought that there would be a small pin slotting into the notches on the blade. Would be a simple solution.
-
The blade won't fall out, so I guess it's safe enough from that perspective. But it won't stay extended by itself, which means that it greatly suffers from actually accomplishing any work without frustrating the user.
Def
-
And yet I have no issues with this tool and use it quite a lot. Maybe I got myself a good copy.

This is how I open and close mine.
<a href="http://s145.photobucket.com/user/Chako_photo/media/Chako_photo004/IMG_2133small_zpsxbsd7mf6.jpg.html" target="_blank" rel="noopener noreferrer"><img src="http://i145.photobucket.com/albums/r207/Chako_photo/Chako_photo004/IMG_2133small_zpsxbsd7mf6.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
I then use my other hand to move the blade. You do have to get over that screw...so you do have to pull up and out at the same time.
I am curious to see how you get along with it. Looks like it is a bad start...not liking that chipped blade at all.
-
Well I was hoping for more from this as I do like a good utility blade knife :-\ The chipped blade off the start is enough to put me off wanting one though :ahhh Hopefully that was a fluke and it ends up being a bit better quality than the first impressions you have of it

-
Oh dear, that doesn't bode well for the ones I have coming. How's the cap lifter on the other end?
-
I've been running so much the past week or so that I haven't had any time to test the bottle opener. :ahhh
I'll do my best to get it done soon, but a bottle opener is a pretty hard thing to screw up.
Def
-
Another contender in the $5 Challenge arrived today and I decided to try Contender 1 to open the package it came in.

As you can see, Contender 1 managed to get a little bit lower in my opinion.

As you can see, not only did the blade fail to stay in the handle, but it also failed to actually cut open the package. Regardless of how well this functions as a bottle opener, I feel safe in calling this one a complete and utter fail. Yes, with practice and use I may be able to use this tool with the knife blade safely inside, but I don't see why a user should "practice" using a knife- it should be there and functional, or it should not be. Period.
I'm afraid this tool is now firmly embedded in the FAIL category.
Def
-
Sorry to hear this. I think you got a really bad example. Mine does not exhibit this behaviour. On the other hand,that is totally unforgivable in something where one can lose a finger using it.
-
The 5 I ordered were waiting for me when I got home and they are different to yours in that they don't ride on a screw. It rides flat on a shelf and the blade is secured very well. I'll strip one and post photos to show.
-
Here's what the ones I got are like...
The tool

The edge showing the shelf the blade rides on

The internals

**
Instructions for use**
It's really easy to deploy the blade and it holds it securely as well. A nice little tool and dirt cheap to boot. Mines definitely a winner

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login