Show off your Sak mod's!
-
Can't wait to see the final result James. Is that a standard 84mm scissor I see?
Yeah, from a Golfer. It's all 84mm donors on this one.
And I am planning to do an 84mm Golfer [emoji23][emoji23][emoji23]

Here it is...I overdid it on the pin that the springs rotate on...so there's a little tightness on the openers layer, mainy the can opener. Hoping after a bunch of open/closing and after oil gets in there it'll be a bit better. Otherwise everything is working. I like the size and wanna try it as EDC instead of Sheila for a while. Though I've been using the pen a lot over the last week...so might miss that.
Also might polish wheel the tools...maybe not... not sure yet.
Did over peen as well on some of my builds. The trick I found was to wiggle the tool in question left and right while opening and closing...
Awesome build by the way... Reminds me of the small huntsman [emoji8]
Sent from my iPhone using Tapatalk
-
I wiggled the tools and stopped hammering as soon as the play was gone..unfortunately there's no way to wiggle the spring. Pretty sure its the spring getting stuck. When I deploy the awl it's loose. Not "side to side" loose, but loose like theres no spring pressure, then if I open can opener or bottle opener and close it again, the awl is tight. So I think the spring isn't moving freely. Like it's getting stuck in a position that makes the awl loose and the can opener tight...but when I do get the can opener deployed, then the awl behaves correctly. Gonna watch it more closely next time.
Main thing I'm excited about is the nail file. Got a Wenger build coming up though that will be all these tools plus the IL phillips/wrench layer. Curious to see how they compare.

-
Yaknow I think I might be wrong about the sticking can opener...now the awl is behaving as normal (after a lot of open/closing).
The can opener spins fine, but if closed gently doesn't snap all the way down. It can easily be opened from this position. If I push it all the way down/closed, then it becomes hard to open.
So maybe it's binding on the liners...?
-
@JamesJ said:
Yaknow I think I might be wrong about the sticking can opener...now the awl is behaving as normal (after a lot of open/closing).The can opener spins fine, but if closed gently doesn't snap all the way down. It can easily be opened from this position. If I push it all the way down/closed, then it becomes hard to open.
So maybe it's binding on the liners...?
Could be the liners... Could also mean the backspring itself is the problem...
Did you use stock 2.2mm pins or had to use a larger diameter pin and bring it down to 2.2mm?
Sent from my iPhone using Tapatalk
-
Yaknow I think I might be wrong about the sticking can opener...now the awl is behaving as normal (after a lot of open/closing).
The can opener spins fine, but if closed gently doesn't snap all the way down. It can easily be opened from this position. If I push it all the way down/closed, then it becomes hard to open.
So maybe it's binding on the liners...?
Could be the liners... Could also mean the backspring itself is the problem...
Did you use stock 2.2mm pins or had to use a larger diameter pin and bring it down to 2.2mm?
Sent from my iPhone using Tapatalk
My gauge said they were between 2.23 and 2.26 after I reduced them
I think it's crowding between the scissors and can opener, when I open the scissors and then kind of press the can opener toward the scissors layer while opening, it moves easier. Could also be rubbing on the outer scale. It's totally flat but maybe I should have used one with the slight "bulge" stamped into it.
At least I know that I can use the can opener if I deploy the scissors first
-
Yaknow I think I might be wrong about the sticking can opener...now the awl is behaving as normal (after a lot of open/closing).
The can opener spins fine, but if closed gently doesn't snap all the way down. It can easily be opened from this position. If I push it all the way down/closed, then it becomes hard to open.
So maybe it's binding on the liners...?
Could be the liners... Could also mean the backspring itself is the problem...
Did you use stock 2.2mm pins or had to use a larger diameter pin and bring it down to 2.2mm?
Sent from my iPhone using Tapatalk
My gauge said they were between 2.23 and 2.26 after I reduced them
Had an experience once where I was test fitting tools using an existing pin... Tools worked out fine snappin and poppin. But when it was assembled using pins that where reduced in size, I had similar problems. Can't exactly pinpoint the cause then, either it was the center pins being over peened or the pins where reduced slightly smaller than 2.2mm..
Your pins should be alright then. Maybe its just some material stuck between backspring and liner.. Just taking a wild guess here...
Sent from my iPhone using Tapatalk
-
Hope you figure out the problem with it James
It is a very nice config in that size SAK 

-
I think I just should have used the liner with the "relief" stamped into it. Not sure what you call it. It kind of bows out to leave room for the tools. The one I used is totally flat. For now I may try sanding the inside surface of the outside liner to kind of give the same effect.
Hoping after maybe 4 or 5 more builds I'll have this figured out better.

-
@HarleyXJGuy said:
It is mine and it is modded does that count as my SAK mod?Anyhow it is a Cybertool / Swisschamp hybrid. Think Cybertool with the mag glass and phillips layer added. Got it for Sir Mike in a lot.

Awesome knife, fellow!! Did yoy keep the fishscaler as well? I carry a normal swisschamp and when I was tempted to change to ct 41 the loss of fishscaler and mag glass really stopped me. I ended up with an xlt haha, but your knife seems like the perfect combination!!
-
Bladeless Ti 58mm

Sent from my E6653 using Tapatalk
-
@Glofindel said:
Bladeless Ti 58mm

Sent from my E6653 using Tapatalk
What a beauty!
Who made the bead?
-
@Glofindel said:
Bladeless Ti 58mm

Sent from my E6653 using Tapatalk
Oh WOW, just WOW!!

-
Bladeless Ti 58mm

Sent from my E6653 using Tapatalk
What a beauty!
Who made the bead?
Russian guy on Facebook group.
Sent from my E6653 using Tapatalk
-
-
@hiraethus said:
Junior/Special Mechanic for the Minimal SAK challenge next month:

I built one of these a while ago, and found I didn't use it (I don't like the combo tool) so took it apart. But I'd like the option of pliers for the 2-layer max challenge, so here's another.Sweet mod H
You obviously get a lot of use from the pliers then -lots of nosehair? :D -
Not yet, but it's getting longer. :-\
-
@hiraethus said:
Junior/Special Mechanic for the Minimal SAK challenge next month:

I built one of these a while ago, and found I didn't use it (I don't like the combo tool) so took it apart. But I'd like the option of pliers for the 2-layer max challenge, so here's another.This is a nice one!

-
Junior/Special Mechanic for the Minimal SAK challenge next month:

I built one of these a while ago, and found I didn't use it (I don't like the combo tool) so took it apart. But I'd like the option of pliers for the 2-layer max challenge, so here's another.This is a nice one!

Totally
I am diggin that mod Hi 
-
Thanks both.

-
Yaknow I think I might be wrong about the sticking can opener...now the awl is behaving as normal (after a lot of open/closing).
The can opener spins fine, but if closed gently doesn't snap all the way down. It can easily be opened from this position. If I push it all the way down/closed, then it becomes hard to open.
So maybe it's binding on the liners...?
Could be the liners... Could also mean the backspring itself is the problem...
Did you use stock 2.2mm pins or had to use a larger diameter pin and bring it down to 2.2mm?
Sent from my iPhone using Tapatalk
My gauge said they were between 2.23 and 2.26 after I reduced them
Had an experience once where I was test fitting tools using an existing pin... Tools worked out fine snappin and poppin. But when it was assembled using pins that where reduced in size, I had similar problems. Can't exactly pinpoint the cause then, either it was the center pins being over peened or the pins where reduced slightly smaller than 2.2mm..
Your pins should be alright then. Maybe its just some material stuck between backspring and liner.. Just taking a wild guess here...
Sent from my iPhone using Tapatalk
I'd guess that you might have a correctly sized pin, but that it got a little bend during peening. If it's still free enough to rotate slowly, whilst bent, relative to the knife scales, that might explain why 1 tool, and then the 2nd tool start having a similar problem (assuming both the tools with the problem are on the same pin).
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login