SOG Scissors? Opinions Needed
-
@IvanDrago said:
Can someone give me the dimensions of those scissors? And diameter of the hole. I consider to put them into Leatherman Rebar.Seems like sLaughtermed would know this
If you have over 5 posts you can PM him 
-
Can someone give me the dimensions of those scissors? And diameter of the hole. I consider to put them into Leatherman Rebar.
Seems like sLaughtermed would know this
If you have over 5 posts you can PM him 
Or he could just wait 20 minutes for me to show up of my own accord :P
Im not sure of the exact length of either the SOG or PST scissors, but both have a 3/16" hole, which is the same size as the Rebars pivots. However, you will run into some compatibility issues with either on the Rebar.
Lets assume the SOG scissors are not too long to fit in the Rebars frame. Because of the length, they could only fit in a long tool slot. If you look at the Rebar's long tools, near these tools pivots, you will see a V shaped notch cut out of them. This notch leaves space for the Rebar's Locking mechanism, which would prevent these tools from closing if the v shaped notch was not present. To fit the SOG scissors, you would probably need to cut off part of the handle, and potentially have to remove the spring. The lock face would also need to be widened slightly. IMO, considering the work involved, and the low quality of the SOG scissors, this mod isn't worth it.
PST scissors are a little easier. They should fit in a Rebars inside tool slot length wise, which is good, because they wont work in a long tool slot (cutting the v shaped notch mentioned above would compromise the scissors). They would have to go in the left most inside tool slot (due to thumb pad) on either handle of the Rebar. Some reshaping of the lock face is needed for this tool to lock, but they were designed not to lock originally, and may not need any work at all. Im not totally sure that cutting a lock notch would work anyhow, since the lock face of PST parts has less material on them to work with.
The best method of putting scissors in a Rebar is New Wave scissors, since it is a proven drop in mod. These have to go in the right most inside tool slot (due to thumb pad), but with some clever Legoing you might be able to fit them in without losing any other tools (you might be able to manage that with PST scissors too, now that I think of it).
-
Can someone give me the dimensions of those scissors? And diameter of the hole. I consider to put them into Leatherman Rebar.
Seems like sLaughtermed would know this
If you have over 5 posts you can PM him 
Or he could just wait 20 minutes for me to show up of my own accord :P
Im not sure of the exact length of either the SOG or PST scissors, but both have a 3/16" hole, which is the same size as the Rebars pivots. However, you will run into some compatibility issues with either on the Rebar.
Lets assume the SOG scissors are not too long to fit in the Rebars frame. Because of the length, they could only fit in a long tool slot. If you look at the Rebar's long tools, near these tools pivots, you will see a V shaped notch cut out of them. This notch leaves space for the Rebar's Locking mechanism, which would prevent these tools from closing if the v shaped notch was not present. To fit the SOG scissors, you would probably need to cut off part of the handle, and potentially have to remove the spring. The lock face would also need to be widened slightly. IMO, considering the work involved, and the low quality of the SOG scissors, this mod isn't worth it.
PST scissors are a little easier. They should fit in a Rebars inside tool slot length wise, which is good, because they wont work in a long tool slot (cutting the v shaped notch mentioned above would compromise the scissors). They would have to go in the left most inside tool slot (due to thumb pad) on either handle of the Rebar. Some reshaping of the lock face is needed for this tool to lock, but they were designed not to lock originally, and may not need any work at all. Im not totally sure that cutting a lock notch would work anyhow, since the lock face of PST parts has less material on them to work with.
The best method of putting scissors in a Rebar is New Wave scissors, since it is a proven drop in mod. These have to go in the right most inside tool slot (due to thumb pad), but with some clever Legoing you might be able to fit them in without losing any other tools (you might be able to manage that with PST scissors too, now that I think of it).
Nope it was a good 40 minutes
:D -
Can someone give me the dimensions of those scissors? And diameter of the hole. I consider to put them into Leatherman Rebar.
Seems like sLaughtermed would know this
If you have over 5 posts you can PM him 
Or he could just wait 20 minutes for me to show up of my own accord :P
Im not sure of the exact length of either the SOG or PST scissors, but both have a 3/16" hole, which is the same size as the Rebars pivots. However, you will run into some compatibility issues with either on the Rebar.
Lets assume the SOG scissors are not too long to fit in the Rebars frame. Because of the length, they could only fit in a long tool slot. If you look at the Rebar's long tools, near these tools pivots, you will see a V shaped notch cut out of them. This notch leaves space for the Rebar's Locking mechanism, which would prevent these tools from closing if the v shaped notch was not present. To fit the SOG scissors, you would probably need to cut off part of the handle, and potentially have to remove the spring. The lock face would also need to be widened slightly. IMO, considering the work involved, and the low quality of the SOG scissors, this mod isn't worth it.
PST scissors are a little easier. They should fit in a Rebars inside tool slot length wise, which is good, because they wont work in a long tool slot (cutting the v shaped notch mentioned above would compromise the scissors). They would have to go in the left most inside tool slot (due to thumb pad) on either handle of the Rebar. Some reshaping of the lock face is needed for this tool to lock, but they were designed not to lock originally, and may not need any work at all. Im not totally sure that cutting a lock notch would work anyhow, since the lock face of PST parts has less material on them to work with.
The best method of putting scissors in a Rebar is New Wave scissors, since it is a proven drop in mod. These have to go in the right most inside tool slot (due to thumb pad), but with some clever Legoing you might be able to fit them in without losing any other tools (you might be able to manage that with PST scissors too, now that I think of it).
Nope it was a good 40 minutes
:DIt took me 20 minutes to write that on my phone

-
[quote author=IvanDrago link=topic=32479.msg1345202#msg1345202 date=1473858656]
Can someone give me the dimensions of those scissors? And diameter of the hole. I consider to put them into Leatherman Rebar.Seems like sLaughtermed would know this
If you have over 5 posts you can PM him 
Or he could just wait 20 minutes for me to show up of my own accord :P
Im not sure of the exact length of either the SOG or PST scissors, but both have a 3/16" hole, which is the same size as the Rebars pivots. However, you will run into some compatibility issues with either on the Rebar.
Lets assume the SOG scissors are not too long to fit in the Rebars frame. Because of the length, they could only fit in a long tool slot. If you look at the Rebar's long tools, near these tools pivots, you will see a V shaped notch cut out of them. This notch leaves space for the Rebar's Locking mechanism, which would prevent these tools from closing if the v shaped notch was not present. To fit the SOG scissors, you would probably need to cut off part of the handle, and potentially have to remove the spring. The lock face would also need to be widened slightly. IMO, considering the work involved, and the low quality of the SOG scissors, this mod isn't worth it.
PST scissors are a little easier. They should fit in a Rebars inside tool slot length wise, which is good, because they wont work in a long tool slot (cutting the v shaped notch mentioned above would compromise the scissors). They would have to go in the left most inside tool slot (due to thumb pad) on either handle of the Rebar. Some reshaping of the lock face is needed for this tool to lock, but they were designed not to lock originally, and may not need any work at all. Im not totally sure that cutting a lock notch would work anyhow, since the lock face of PST parts has less material on them to work with.
The best method of putting scissors in a Rebar is New Wave scissors, since it is a proven drop in mod. These have to go in the right most inside tool slot (due to thumb pad), but with some clever Legoing you might be able to fit them in without losing any other tools (you might be able to manage that with PST scissors too, now that I think of it).
Nope it was a good 40 minutes
:DIt took me 20 minutes to write that on my phone

[/quote]You need a bluetooth keyboard then


-
Thx for fast reply. So the bottom line is SSS? (SOG Scissors Sucks ;) ) I will look for sth from Leatherman or Vic stable then
-
@IvanDrago said:
Thx for fast reply. So the bottom line is SSS? (SOG Scissors Sucks ;) ) I will look for sth from Leatherman or Vic stable thenDont forget that Gerber, bing owned by Fiskars, makes a great pair of multi tool scissors
-
@sLaughterMed said:
...
Dont forget that Gerber, bing owned by Fiskars, makes a great pair of multi tool scissorsnot sure if always so good: https://www.youtube.com/watch?v=-i53ENjtUZ0
-
...
Dont forget that Gerber, bing owned by Fiskars, makes a great pair of multi tool scissorsnot sure if always so good: https://www.youtube.com/watch?v=-i53ENjtUZ0
Actually, those scissors are great (when they are built correctly). I'd attribute that to Gerbers poor QC for many of it's Chinese made tools than bad scissor deisgn. The MP600 & MP400 have the same scissor design as that Bear Grylls tool, and are fantastic scissors. Even the Diesel (which is made in China) has good scissors, although not as good as it's American counterparts.
If you want to get a Gerber, stay away from the Suspension family, and anything marked Bear Grylls (except the Strata clone, that one is pretty good). Sadly, these are Gerber's best sellers, and give the rest of the self respecting tools a bad name
-
A good alternative to the SOG scissors is their V-cutter. I know it's not scissors, but it can do a lot of the same stuff. It takes up less room in your tool, as well.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login