Show off your Sak mod's!
-
Yaknow I think I might be wrong about the sticking can opener...now the awl is behaving as normal (after a lot of open/closing).
The can opener spins fine, but if closed gently doesn't snap all the way down. It can easily be opened from this position. If I push it all the way down/closed, then it becomes hard to open.
So maybe it's binding on the liners...?
Could be the liners... Could also mean the backspring itself is the problem...
Did you use stock 2.2mm pins or had to use a larger diameter pin and bring it down to 2.2mm?
Sent from my iPhone using Tapatalk
My gauge said they were between 2.23 and 2.26 after I reduced them
Had an experience once where I was test fitting tools using an existing pin... Tools worked out fine snappin and poppin. But when it was assembled using pins that where reduced in size, I had similar problems. Can't exactly pinpoint the cause then, either it was the center pins being over peened or the pins where reduced slightly smaller than 2.2mm..
Your pins should be alright then. Maybe its just some material stuck between backspring and liner.. Just taking a wild guess here...
Sent from my iPhone using Tapatalk
I'd guess that you might have a correctly sized pin, but that it got a little bend during peening. If it's still free enough to rotate slowly, whilst bent, relative to the knife scales, that might explain why 1 tool, and then the 2nd tool start having a similar problem (assuming both the tools with the problem are on the same pin).
-
Yesterday I received a modded Yeoman that I won in an online auction. Unfortunately, the action on almost all of the tools was sluggish and no amount of oil could fix it. The springs seemed weak and I suspected the possibility of a bent pin. I took matters into my own hands and rebuilt the whole thing using parts from a beat up Explorer. Here's the result:


Everything works great now. This was my first 91mm build and peening job, but I'm happy I bit the bullet and went for it.
Sent from my iPhone using Tapatalk
-
@Psych said:
Yesterday I received a modded Yeoman that I won in an online auction. Unfortunately, the action on almost all of the tools was sluggish and no amount of oil could fix it. The springs seemed weak and I suspected the possibility of a bent pin. I took matters into my own hands and rebuilt the whole thing using parts from a beat up Explorer. Here's the result:Everything works great now. This was my first 91mm build and peening job, but I'm happy I bit the bullet and went for it.
Good work!
-
@Psych said:
Yesterday I received a modded Yeoman that I won in an online auction. Unfortunately, the action on almost all of the tools was sluggish and no amount of oil could fix it. The springs seemed weak and I suspected the possibility of a bent pin. I took matters into my own hands and rebuilt the whole thing using parts from a beat up Explorer. Here's the result:

Everything works great now. This was my first 91mm build and peening job, but I'm happy I bit the bullet and went for it.
Sent from my iPhone using Tapatalk
Nice mod... looks factory [emoji8][emoji8][emoji8]
Sent from my iPhone using Tapatalk
-
@Psych said:
Yesterday I received a modded Yeoman that I won in an online auction. Unfortunately, the action on almost all of the tools was sluggish and no amount of oil could fix it. The springs seemed weak and I suspected the possibility of a bent pin. I took matters into my own hands and rebuilt the whole thing using parts from a beat up Explorer. Here's the result:

Everything works great now. This was my first 91mm build and peening job, but I'm happy I bit the bullet and went for it.
Sent from my iPhone using Tapatalk
Great job! Love the Yeoman

-
Thanks for the compliments everyone. I couldn't have done it without the knowledge gained from this forum.
Yesterday I received a modded Yeoman that I won in an online auction. Unfortunately, the action on almost all of the tools was sluggish and no amount of oil could fix it. The springs seemed weak and I suspected the possibility of a bent pin. I took matters into my own hands and rebuilt the whole thing using parts from a beat up Explorer. Here's the result:


Everything works great now. This was my first 91mm build and peening job, but I'm happy I bit the bullet and went for it.
Sent from my iPhone using Tapatalk
Nice mod... looks factory [emoji8][emoji8][emoji8]
It actually functions better than some factory models I've received. Sometimes I've gotten explorers where the snap on the screwdriver/mag glass layer is nonexistent (that was the case with the explorer I took apart to make this). Not sure what improved it.
-
Excellent job Psych

-
@Psych said:
Thanks for the compliments everyone. I couldn't have done it without the knowledge gained from this forum.Yesterday I received a modded Yeoman that I won in an online auction. Unfortunately, the action on almost all of the tools was sluggish and no amount of oil could fix it. The springs seemed weak and I suspected the possibility of a bent pin. I took matters into my own hands and rebuilt the whole thing using parts from a beat up Explorer. Here's the result:


Everything works great now. This was my first 91mm build and peening job, but I'm happy I bit the bullet and went for it.
Sent from my iPhone using Tapatalk
Nice mod... looks factory [emoji8][emoji8][emoji8]
It actually functions better than some factory models I've received. Sometimes I've gotten explorers where the snap on the screwdriver/mag glass layer is nonexistent (that was the case with the explorer I took apart to make this). Not sure what improved it.
Probably corrosion on the liners. If there's enough corrosion, it will keep the spring from moving freely (from a combination of friction and compression). Usually WD-40 and tooth floss is sufficent to fix it.
Nice job on the mod

-
@Psych said:
Yesterday I received a modded Yeoman that I won in an online auction. Unfortunately, the action on almost all of the tools was sluggish and no amount of oil could fix it. The springs seemed weak and I suspected the possibility of a bent pin. I took matters into my own hands and rebuilt the whole thing using parts from a beat up Explorer. Here's the result:

Everything works great now. This was my first 91mm build and peening job, but I'm happy I bit the bullet and went for it.
Sent from my iPhone using Tapatalk
Great work!

-
@Wade Eva said:
My first 91mm mod. Older Ranger with brass liners, toothpick and tweezer head. Homemade pocket dangler and a moded Maglite Solitaire (LED).


[URL=http://s1007.photobucket.com/user/wadeeva/media/IMG_5891.jpg.htmlHi,
I know it's a bit late, but how did you get the Brass to sick to the tweezers? That's exactly what I'm wanting to do on one of my next mods and I can't quite decide how to do it.
Rototype
-
@Wade Eva said:
My first 91mm mod. Older Ranger with brass liners, toothpick and tweezer head. Homemade pocket dangler and a moded Maglite Solitaire (LED).


[I don't know how he did it but I soldered two brass pins. It's not finished yet but here's a link to the work in progress: [url=/post/1334516]Cap lifter on an Executive](http://s1007.photobucket.com/user/wadeeva/media/IMG_5891.jpg.html
Hi,
I know it's a bit late, but how did you get the Brass to sick to the tweezers? That's exactly what I'm wanting to do on one of my next mods and I can't quite decide how to do it.
Rototype
[/quote). I got the pins second hand but they should be available. Just look for places that sell beads for homemade jewellery. -
@Wade Eva said:
My first 91mm mod. Older Ranger with brass liners, toothpick and tweezer head. Homemade pocket dangler and a moded Maglite Solitaire (LED).


[Cap lifter on an Executive](http://s1007.photobucket.com/user/wadeeva/media/IMG_5891.jpg.htmlHi,
I know it's a bit late, but how did you get the Brass to sick to the tweezers? That's exactly what I'm wanting to do on one of my next mods and I can't quite decide how to do it.
Rototype
I don't know how he did it but I soldered two brass pins. It's not finished yet but here's a link to the work in progress: [url=/post/1334516). I got the pins second hand but they should be available. Just look for places that sell beads for homemade jewellery.
[/quote]Can't wait to see what you come up with
and that Ranger is so

-
Due to being obsessed with small details, I completely tore apart the blue Yeoman I built the other day because the snap when closing the philips screwdriver wasn't as perfect as I would have liked. I totally rebuilt it and now it's up to standards.




And it's GREEN!!!!!!
Sent from my iPhone using Tapatalk
-
:D :D :D :D :D :D :D
-
My first mod was acttually just adding Plus scales to a Camper - seems like I only needed the one side and only for the pen slot as it appears, the standard scales already have the pin slot already cut but I changed both to keep it matching. I took lots of photos so I might put it up some time as a 'dummy's guide' for just the scale swaps (would it be worth doing a video tutorial?).
The next one's going to be a Waiter from a Bantam with the corkscrew from a tourist (yeah, I know I could have just swapped the multi opener and dropped the other bits but I want this one to be a little more special than that). Best thing is, with the Standard I also got at the same time I can almost do 2 of them so a friend might be getting a nice Xmas pressie this year - don't think they'll notice the difference between the multi tool and the cap lifter. The scales are the special part on the Waiter - I purchased a BIG lump of Yew wood (25lbs/12kg) recently, and it all seems to have very nice grain on it. The Brass sheet arrived today (3 days early, was scheduled to get here Tuesday but I'm not complaining - means I have tomorrow to work on them...).
Ultimately I want to work on an enhancement for the Camper. I'd like scissors on there but I want to ditch the hook, possibly drop the small blade for a combi opener or a sheeps-foot or pruner blade and then add the magnifying glass and a back phillips (to replace the hook), all wrapped in wooden scales with Plus accessories in them (and brass liners of course) - hence the earlier question about the brass handle for the tweezers. The pen might be a little more chalenging but I think I might have a handle on that now (pun intended), maybe even make the brass toothpick as well.
-
First teaser pics of the Waiter. Nowhere near finished but this side looks OK, and it sort of shows what I'm doing with the corkscrew.


-
-
@Psych said:
Due to being obsessed with small details, I completely tore apart the blue Yeoman I built the other day because the snap when closing the philips screwdriver wasn't as perfect as I would have liked. I totally rebuilt it and now it's up to standards.



And it's GREEN!!!!!!
Sent from my iPhone using Tapatalk
Even better! Super sweet mod Psych

-
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

