Show off your Sak mod's!
-
@Glofindel said:
Bladeless Ti 58mm

Sent from my E6653 using Tapatalk
Oh WOW, just WOW!!

-
Bladeless Ti 58mm

Sent from my E6653 using Tapatalk
What a beauty!
Who made the bead?
Russian guy on Facebook group.
Sent from my E6653 using Tapatalk
-
-
@hiraethus said:
Junior/Special Mechanic for the Minimal SAK challenge next month:

I built one of these a while ago, and found I didn't use it (I don't like the combo tool) so took it apart. But I'd like the option of pliers for the 2-layer max challenge, so here's another.Sweet mod H
You obviously get a lot of use from the pliers then -lots of nosehair? :D -
Not yet, but it's getting longer. :-\
-
@hiraethus said:
Junior/Special Mechanic for the Minimal SAK challenge next month:

I built one of these a while ago, and found I didn't use it (I don't like the combo tool) so took it apart. But I'd like the option of pliers for the 2-layer max challenge, so here's another.This is a nice one!

-
Junior/Special Mechanic for the Minimal SAK challenge next month:

I built one of these a while ago, and found I didn't use it (I don't like the combo tool) so took it apart. But I'd like the option of pliers for the 2-layer max challenge, so here's another.This is a nice one!

Totally
I am diggin that mod Hi 
-
Thanks both.

-
Yaknow I think I might be wrong about the sticking can opener...now the awl is behaving as normal (after a lot of open/closing).
The can opener spins fine, but if closed gently doesn't snap all the way down. It can easily be opened from this position. If I push it all the way down/closed, then it becomes hard to open.
So maybe it's binding on the liners...?
Could be the liners... Could also mean the backspring itself is the problem...
Did you use stock 2.2mm pins or had to use a larger diameter pin and bring it down to 2.2mm?
Sent from my iPhone using Tapatalk
My gauge said they were between 2.23 and 2.26 after I reduced them
Had an experience once where I was test fitting tools using an existing pin... Tools worked out fine snappin and poppin. But when it was assembled using pins that where reduced in size, I had similar problems. Can't exactly pinpoint the cause then, either it was the center pins being over peened or the pins where reduced slightly smaller than 2.2mm..
Your pins should be alright then. Maybe its just some material stuck between backspring and liner.. Just taking a wild guess here...
Sent from my iPhone using Tapatalk
I'd guess that you might have a correctly sized pin, but that it got a little bend during peening. If it's still free enough to rotate slowly, whilst bent, relative to the knife scales, that might explain why 1 tool, and then the 2nd tool start having a similar problem (assuming both the tools with the problem are on the same pin).
-
Yesterday I received a modded Yeoman that I won in an online auction. Unfortunately, the action on almost all of the tools was sluggish and no amount of oil could fix it. The springs seemed weak and I suspected the possibility of a bent pin. I took matters into my own hands and rebuilt the whole thing using parts from a beat up Explorer. Here's the result:


Everything works great now. This was my first 91mm build and peening job, but I'm happy I bit the bullet and went for it.
Sent from my iPhone using Tapatalk
-
@Psych said:
Yesterday I received a modded Yeoman that I won in an online auction. Unfortunately, the action on almost all of the tools was sluggish and no amount of oil could fix it. The springs seemed weak and I suspected the possibility of a bent pin. I took matters into my own hands and rebuilt the whole thing using parts from a beat up Explorer. Here's the result:Everything works great now. This was my first 91mm build and peening job, but I'm happy I bit the bullet and went for it.
Good work!
-
@Psych said:
Yesterday I received a modded Yeoman that I won in an online auction. Unfortunately, the action on almost all of the tools was sluggish and no amount of oil could fix it. The springs seemed weak and I suspected the possibility of a bent pin. I took matters into my own hands and rebuilt the whole thing using parts from a beat up Explorer. Here's the result:

Everything works great now. This was my first 91mm build and peening job, but I'm happy I bit the bullet and went for it.
Sent from my iPhone using Tapatalk
Nice mod... looks factory [emoji8][emoji8][emoji8]
Sent from my iPhone using Tapatalk
-
@Psych said:
Yesterday I received a modded Yeoman that I won in an online auction. Unfortunately, the action on almost all of the tools was sluggish and no amount of oil could fix it. The springs seemed weak and I suspected the possibility of a bent pin. I took matters into my own hands and rebuilt the whole thing using parts from a beat up Explorer. Here's the result:

Everything works great now. This was my first 91mm build and peening job, but I'm happy I bit the bullet and went for it.
Sent from my iPhone using Tapatalk
Great job! Love the Yeoman

-
Thanks for the compliments everyone. I couldn't have done it without the knowledge gained from this forum.
Yesterday I received a modded Yeoman that I won in an online auction. Unfortunately, the action on almost all of the tools was sluggish and no amount of oil could fix it. The springs seemed weak and I suspected the possibility of a bent pin. I took matters into my own hands and rebuilt the whole thing using parts from a beat up Explorer. Here's the result:


Everything works great now. This was my first 91mm build and peening job, but I'm happy I bit the bullet and went for it.
Sent from my iPhone using Tapatalk
Nice mod... looks factory [emoji8][emoji8][emoji8]
It actually functions better than some factory models I've received. Sometimes I've gotten explorers where the snap on the screwdriver/mag glass layer is nonexistent (that was the case with the explorer I took apart to make this). Not sure what improved it.
-
Excellent job Psych

-
@Psych said:
Thanks for the compliments everyone. I couldn't have done it without the knowledge gained from this forum.Yesterday I received a modded Yeoman that I won in an online auction. Unfortunately, the action on almost all of the tools was sluggish and no amount of oil could fix it. The springs seemed weak and I suspected the possibility of a bent pin. I took matters into my own hands and rebuilt the whole thing using parts from a beat up Explorer. Here's the result:


Everything works great now. This was my first 91mm build and peening job, but I'm happy I bit the bullet and went for it.
Sent from my iPhone using Tapatalk
Nice mod... looks factory [emoji8][emoji8][emoji8]
It actually functions better than some factory models I've received. Sometimes I've gotten explorers where the snap on the screwdriver/mag glass layer is nonexistent (that was the case with the explorer I took apart to make this). Not sure what improved it.
Probably corrosion on the liners. If there's enough corrosion, it will keep the spring from moving freely (from a combination of friction and compression). Usually WD-40 and tooth floss is sufficent to fix it.
Nice job on the mod

-
@Psych said:
Yesterday I received a modded Yeoman that I won in an online auction. Unfortunately, the action on almost all of the tools was sluggish and no amount of oil could fix it. The springs seemed weak and I suspected the possibility of a bent pin. I took matters into my own hands and rebuilt the whole thing using parts from a beat up Explorer. Here's the result:

Everything works great now. This was my first 91mm build and peening job, but I'm happy I bit the bullet and went for it.
Sent from my iPhone using Tapatalk
Great work!

-
@Wade Eva said:
My first 91mm mod. Older Ranger with brass liners, toothpick and tweezer head. Homemade pocket dangler and a moded Maglite Solitaire (LED).


[URL=http://s1007.photobucket.com/user/wadeeva/media/IMG_5891.jpg.htmlHi,
I know it's a bit late, but how did you get the Brass to sick to the tweezers? That's exactly what I'm wanting to do on one of my next mods and I can't quite decide how to do it.
Rototype
-
@Wade Eva said:
My first 91mm mod. Older Ranger with brass liners, toothpick and tweezer head. Homemade pocket dangler and a moded Maglite Solitaire (LED).


[I don't know how he did it but I soldered two brass pins. It's not finished yet but here's a link to the work in progress: [url=/post/1334516]Cap lifter on an Executive](http://s1007.photobucket.com/user/wadeeva/media/IMG_5891.jpg.html
Hi,
I know it's a bit late, but how did you get the Brass to sick to the tweezers? That's exactly what I'm wanting to do on one of my next mods and I can't quite decide how to do it.
Rototype
[/quote). I got the pins second hand but they should be available. Just look for places that sell beads for homemade jewellery. -
@Wade Eva said:
My first 91mm mod. Older Ranger with brass liners, toothpick and tweezer head. Homemade pocket dangler and a moded Maglite Solitaire (LED).


[Cap lifter on an Executive](http://s1007.photobucket.com/user/wadeeva/media/IMG_5891.jpg.htmlHi,
I know it's a bit late, but how did you get the Brass to sick to the tweezers? That's exactly what I'm wanting to do on one of my next mods and I can't quite decide how to do it.
Rototype
I don't know how he did it but I soldered two brass pins. It's not finished yet but here's a link to the work in progress: [url=/post/1334516). I got the pins second hand but they should be available. Just look for places that sell beads for homemade jewellery.
[/quote]Can't wait to see what you come up with
and that Ranger is so

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login